The steering lock actuator activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little in the same manner as is done for a vehicle with a mechanical key to change the position of the lock hole.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Unable to lock steering wheel |
Main Body
·
FR Door Courtesy ·
FL Door Courtesy |
- |
When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.
Perform either of the following operations to lock/unlock the steering:
To unlock the steering, carry the key and turn the power switch on (ACC) or on (IG) with the shift lever in P.
To lock the steering, turn the power switch off with the shift lever in P, and then open a door.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
The steering lock system uses LIN communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
When replacing the steering lock ECU (steering lock actuator assembly), certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU), registration must be performed (refer to Service Bulletin).
After performing repairs, confirm that the problem does not occur.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Using the intelligent tester, confirm the output of DTCs for all systems.
No DTCs are output.
When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle and select "Manual" from the initial screen on the intelligent tester. Select "Key Code Registration" under model code.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart (See page Steering>STEERING COLUMN>STEERING LOCK SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
OK
NG
Use the Data List to check if the steering lock command is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Lock Request Receive | Reception state of steering lock request signal by certification ECU (smart key ECU assembly) and sent to ID code box (immobiliser code ECU) / OK or NG
|
OK: Within 10 seconds of opening any door with power switch off and shift lever in P
NG: Except above |
If this item does not change to "OK" even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the power switch from on (IG) to off and opening a door with the shift lever in P, and OK is displayed on the intelligent tester screen.
OK
NG
OK
NG
OK
NG
Using the intelligent tester, check the following main body ECU Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Door Courtesy*1 | Front door courtesy light switch assembly RH / CLOSE or OPEN | CLOSE: Front door RH closed
OPEN: Front door RH open |
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or a related part. |
| FL Door Courtesy*2 | Front door courtesy light switch assembly LH / CLOSE or OPEN | CLOSE: Front door LH closed
OPEN: Front door LH open |
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or a related part. |
*1: for RHD
*2: for LHD
The Data List item changes in accordance with the opening and closing of the driver door.
OK
NG
Use the Data List to check if S code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the hybrid control system cannot be started). |
OK is displayed on the intelligent tester.
Reasons for verification failure:
The certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
OK
NG
Use the Data List to check if L code certification is functioning properly.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU is not registered or the ID code box (immobiliser code ECU) or steering lock ECU is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the hybrid control system cannot be started). |
OK is displayed on the intelligent tester.
Reasons for verification failure:
The steering lock ECU or ID code box (immobiliser code ECU) is malfunctioning.
There is a problem with the communication between ECUs.
An ECU is replaced, but is not registered.
An ECU is replaced with an ECU which has a code already stored in it.
OK
NG
Replace the steering lock ECU (steering lock actuator assembly) with a new one (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY).
Perform registration (refer to Service Bulletin).
Turn the power switch on (IG).
Turn the steering wheel and check the steering condition.
Steering is unlocked.
OK
NG
Replace the ID code box (immobiliser code ECU) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if S code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| S Code Check | Verification result between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is not registered or the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the hybrid control system cannot be started). |
OK is displayed on the intelligent tester.
OK
NG
Replace the ID code box (immobiliser code ECU) with a new one.
Perform registration (refer to Service Bulletin).
Use the Data List to check if L code certification is functioning properly again.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| L Code Check | Verification result between ID code box (immobiliser code ECU) and steering lock ECU / OK or NG | OK: Verification result normal
NG: Verification result abnormal |
When a malfunction is present:
·
The ID code for the ID code box (immobiliser code ECU) or steering lock ECU is not registered or the ID code box (immobiliser code ECU) or steering lock ECU is malfunctioning. ·
The steering cannot be locked. ·
The steering cannot be unlocked (the hybrid control system cannot be started). |
OK is displayed on the intelligent tester.
OK
NG