Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2011.12–2014.12
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0129  Lost Communication with Brake System Control Module  U0293  Lost Communication with HV ECU  


DESCRIPTION

·

The power management control ECU communicates with the ECM and brake booster with master cylinder assembly (skid control ECU). When the power management control ECU does not receive data from the ECM or brake booster with master cylinder assembly (skid control ECU), the power management control ECU stores DTC U0100 or U0129.

·

The ECM communicates with the power management control ECU. When the ECM does not receive data from the power management control ECU, the ECM stores DTC U0293.

·

The brake booster with master cylinder assembly (skid control ECU) communicates with the power management control ECU. When the brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU, the brake booster with master cylinder assembly (skid control ECU) stores DTC U0293.


DTC No. DTC Detection Condition Trouble Area
U0100 The power management control ECU does not receive data from the ECM.
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of ECM

·

ECM

·

Open or short in CAN junction connector LH


U0129 The power management control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU).
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU)

·

Open or short in CAN junction connector LH


U0293
·

The ECM does not receive data from the power management control ECU.

·

The brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU.


·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of ECM

·

ECM

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU)

·

Open or short in CAN junction connector LH



HINT:

This diagnosis procedure is for when DTC U0100, U0129 and U0293 are output at the same time.


WIRING DIAGRAM

C251628E02
0.919,0.943 1.265,1.229 0.347,0.286 10 G58 1.226,0.943 2.536,1.278 1.309,0.335 10 Power Management Control ECU 0.861,3.992 2.854,4.326 1.993,0.335 10 CAN Junction Connector LH 2.02,6.778 2.407,7.113 0.387,0.335 10 ECM 1.695,6.778 1.980,7.113 0.286,0.335 10 A40 5.26,4.542 6.986,5.053 1.727,0.511 10 Brake Booster with Master Cylinder Assembly (Skid Control ECU) 4.922,4.542 5.209,4.904 0.287,0.362 10 A41 3.328,0.777 3.842,0.968 0.514,0.191 10 120 Ω 3.3,7.046 3.814,7.237 0.514,0.191 10 120 Ω 2.686,1.362 3.109,1.541 0.423,0.179 10 CA3N 3.995,1.362 4.418,1.541 0.423,0.179 10 CA3P 5.868,3.477 6.291,3.656 0.423,0.179 10 CA2H 5.868,4.118 6.291,4.297 0.423,0.179 10 CA2L 2.68,6.434 3.103,6.613 0.423,0.179 10 CANN 3.966,6.434 4.389,6.613 0.423,0.179 10 CANP 2.929,1.648 3.155,1.882 0.226,0.234 10 30 3.983,1.648 4.209,1.882 0.226,0.234 10 31 2.915,6.168 3.141,6.402 0.226,0.234 10 25 3.969,6.168 4.195,6.402 0.226,0.234 10 12 2.719,2.982 2.945,3.216 0.226,0.234 10 21 4.158,2.982 4.384,3.216 0.226,0.234 10 10 2.887,2.262 3.113,2.496 0.226,0.234 10 W 4.039,2.262 4.265,2.496 0.226,0.234 10 R 5.192,3.401 5.418,3.635 0.226,0.234 10 L 5.168,4.188 5.394,4.422 0.226,0.234 10 W 2.887,5.678 3.113,5.911 0.226,0.234 10 W 4.039,5.678 4.265,5.911 0.226,0.234 10 B 4.339,3.372 4.565,3.606 0.226,0.234 10 1 4.311,4.176 4.537,4.410 0.226,0.234 10 12 5.653,3.473 5.879,3.707 0.226,0.234 10 35 5.653,4.117 5.879,4.351 0.226,0.234 10 34 2.775,4.975 3.001,5.209 0.226,0.234 10 14 4.165,4.975 4.391,5.209 0.226,0.234 10 3 0.936,8.001 2.839,8.181 1.903,0.179 10 : CAN Main Bus Line (CANH) 0.936,8.409 2.839,8.588 1.903,0.179 10 : CAN Main Bus Line (CANL) 3.89,8.005 5.793,8.184 1.903,0.179 10 : CAN Branch Line (CANH) 3.89,8.413 5.793,8.592 1.903,0.179 10 : CAN Branch Line (CANL) 0.145,0.111 1.829,0.614 1.684,0.503 12 Sub Bus 15: 4.283,3.609 4.570,3.970 0.287,0.362 10 A51 4.283,3.979 4.570,4.341 0.287,0.362 10 A51 3.79,4.956 4.077,5.318 0.287,0.362 10 A51 3.026,4.956 3.313,5.318 0.287,0.362 10 A51 3.019,3.02 3.307,3.382 0.287,0.362 10 G71 3.774,3.02 4.061,3.382 0.287,0.362 10 G71 5.486,0.773 6.926,1.111 1.440,0.339 10 X: Suspected Area

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Check if Hybrid Control of the power management control ECU outputs only DTC U0129.

HINT:

If the power management control ECU outputs only DTC U0129, troubleshoot DTC U0129 and check the branch circuit of sub bus 15.


Result:
Result Proceed to
The power management control ECU outputs DTC U0129 and other DTCs.
(Intelligent tester display: Hybrid Control)
A
The power management control ECU outputs only DTC U0129.
(Intelligent tester display: Hybrid Control)
B




A

2.CHECK SUB BUS 15

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK SUB BUS 15
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183643E02
2.427,1.115 2.604,0.563 2.604,0.563 2.74,0.563 false 1.823,1.104 1.677,0.531 1.677,0.531 1.458,0.531 false 2.417,1.313 2.26,1.823 2.26,1.823 2.052,1.823 false 2.469,1.313 2.625,1.823 2.625,1.823 2.833,1.823 false 1.927,0.25 2.365,0.51 0.438,0.26 10 false G57 2.51,0.24 2.948,0.5 0.438,0.26 10 false G58 2.792,0.479 3.292,0.698 0.5,0.219 10 false AM21 1.24,0.438 1.5,0.646 0.26,0.208 10 false E1 1.656,1.719 2.156,1.938 0.5,0.219 10 false CA3P 2.885,1.74 3.344,1.958 0.458,0.219 10 false CA3N 0.052,0.052 0.354,0.313 0.302,0.26 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
G58-31 (CA3P) - G58-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
G58-31 (CA3P) - G57-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
G58-30 (CA3N) - G57-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
G58-31 (CA3P) - G58-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
G58-30 (CA3N) - G58-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

When the values are as specified, clear and recheck for DTCs. When no DTCs are output, check for malfunctions such as damage or improper connection of the relevant connectors.

·

If DTCs are output although the bus circuit is normal and DTCs were cleared, replace the power management control ECU.



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus line) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D




A

B

3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (POWER MANAGEMENT CONTROL ECU)

C

7.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU - CAN J/C LH)

D

12.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (POWER MANAGEMENT CONTROL ECU)
a.
U158843E02
1.708,2.771 2.427,2.573 false 1.75,3.063 2.469,2.583 false 2.531,3.01 2.927,3.208 0.396,0.198 10 false G58 1.292,2.688 1.677,2.865 0.385,0.177 10 false CA3P 1.344,2.969 1.729,3.146 0.385,0.177 10 false CA3N 0.156,0.052 0.479,0.333 0.323,0.281 10 false *a

Disconnect the G58 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-31 (CA3P) - G58-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)
4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)
a.

Reconnect the G58 power management control ECU connector.


b.
U159393E03
2.188,1.365 2.188,0.521 2.188,0.521 2.406,0.521 false 2.177,1.563 2.177,1.938 2.177,1.938 2.396,1.938 false 0.156,0.125 0.771,0.531 0.615,0.406 10 false *a 0.552,1.229 0.979,1.5 0.427,0.271 10 false G71 2.479,0.438 3.063,0.667 0.583,0.229 10 false CANH*b 2.469,1.844 3.042,2.063 0.573,0.219 10 false CANL*b

Disconnect the G71 CAN junction connector LH (instrument panel wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G71-10 (CANH) - G71-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Power Management Control ECU



OK

5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - CAN J/C LH)

5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)
a.

Reconnect the G71 CAN junction connector LH (instrument panel wire side).


b.
U159394E02
1.406,1.375 1.406,0.531 1.406,0.531 1.188,0.531 false 1.406,1.573 1.406,1.948 1.406,1.948 1.198,1.948 false 0.156,0.083 0.771,0.49 0.615,0.406 10 false *a 0.563,1.219 0.99,1.49 0.427,0.271 10 false A51 0.615,0.448 1.198,0.677 0.583,0.229 10 false CANH*b 0.656,1.875 1.229,2.094 0.573,0.219 10 false CANL*b

Disconnect the A51 CAN junction connector LH (engine room main wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A51-3 (CANH) - A51-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM



OK

REPLACE CAN JUNCTION CONNECTOR LH

NG

6.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN J/C LH)
6.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN J/C LH)
a.

Reconnect the A51 CAN junction connector LH (engine room main wire side).


b.
U159409E03
2.5,1.625 2.865,1.625 2.865,1.625 2.865,2.406 false 2.49,1.531 2.49,0.938 2.49,0.938 2.729,0.938 false 0.156,0.125 0.396,0.365 0.24,0.24 10 false *a 2.802,0.854 3.24,1.052 0.438,0.198 10 false CANP 2.677,2.448 3.146,2.646 0.469,0.198 10 false CANN 1.781,0.708 2.063,0.885 0.281,0.177 10 false A40

Disconnect the A40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-12 (CANP) - A40-25 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CAN J/C LH)

7.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU - CAN J/C LH)
a.
U158843E02
1.708,2.771 2.427,2.573 false 1.75,3.063 2.469,2.583 false 2.531,3.01 2.927,3.208 0.396,0.198 10 false G58 1.292,2.688 1.677,2.865 0.385,0.177 10 false CA3P 1.344,2.969 1.729,3.146 0.385,0.177 10 false CA3N 0.156,0.052 0.479,0.333 0.323,0.281 10 false *a

Disconnect the G58 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-31 (CA3P) - G58-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

8.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
8.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
a.

Reconnect the G58 power management control ECU connector.


b.
U159393E04
2.188,1.365 2.188,0.521 2.188,0.521 2.406,0.521 false 2.177,1.563 2.177,1.938 2.177,1.938 2.396,1.938 false 0.156,0.125 0.771,0.531 0.615,0.406 10 false *a 0.552,1.229 0.979,1.5 0.427,0.271 10 false G71 2.479,0.438 3.063,0.667 0.583,0.229 10 false CANH*b 2.469,1.844 3.042,2.063 0.573,0.219 10 false CANL*b

Disconnect the G71 CAN junction connector LH (instrument panel wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G71-10 (CANH) - G71-21 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Power Management Control ECU



OK

9.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - CAN J/C LH)

9.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
a.

Reconnect the G71 CAN junction connector LH (instrument panel wire side).


b.
C354333E01
0.417,1.167 0.833,1.417 0.417,0.25 1.167,1.417 1.167,0.583 1.167,0.583 0.917,0.583 false 1.375,1.406 1.375,0.583 1.375,0.583 2.083,0.583 false 0.917,1.917 1.156,1.917 1.156,1.917 1.156,1.542 false 2.083,1.917 1.385,1.917 1.385,1.917 1.385,1.542 false 0.083,0.125 0.49,0.385 0.406,0.26 10 false *a 0.354,0.5 0.979,0.802 0.625,0.302 10 false CANH*b 0.375,1.823 1,2.083 0.625,0.26 10 false CANL*b 0.5,1.208 0.906,1.469 0.406,0.26 10 false A51 2.135,0.49 2.76,0.792 0.625,0.302 10 false CANH*c 2.135,1.823 2.76,2.083 0.625,0.26 10 false CANL*c

Disconnect the A51 CAN junction connector LH (engine room main wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A51-1 (CANH) - A51-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (skid control ECU)
A51-3 (CANH) - A51-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to Brake Booster with Master Cylinder Assembly (skid control ECU)
*c to ECM

Result:
Result Proceed to
OK A
NG (Short circuit between bus lines in ECM CAN main bus line) B
NG (Short circuit between bus lines in brake booster with master cylinder assembly (skid control ECU) CAN branch line) C




A

REPLACE CAN JUNCTION CONNECTOR LH

B

10.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN J/C LH)

C

11.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CAN J/C LH)
10.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN J/C LH)
a.

Reconnect the A51 CAN junction connector LH (engine room main wire side).


b.
U159409E03
2.5,1.625 2.865,1.625 2.865,1.625 2.865,2.406 false 2.49,1.531 2.49,0.938 2.49,0.938 2.729,0.938 false 0.156,0.125 0.396,0.365 0.24,0.24 10 false *a 2.802,0.854 3.24,1.052 0.438,0.198 10 false CANP 2.677,2.448 3.146,2.646 0.469,0.198 10 false CANN 1.781,0.708 2.063,0.885 0.281,0.177 10 false A40

Disconnect the A40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-12 (CANP) - A40-25 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CAN J/C LH)

11.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CAN J/C LH)
a.

Reconnect the A51 CAN junction connector LH (engine room main wire side).


b.
U159481E02
1.656,2.135 1.656,2.708 1.656,2.708 1.427,2.708 false 1.76,2.135 1.76,2.708 1.76,2.708 1.979,2.708 false 0.198,0.167 0.406,0.323 0.208,0.156 10 false *a 1.625,0.875 1.917,1.031 0.292,0.156 10 false A41 2.031,2.625 2.51,2.802 0.479,0.177 10 false CA2H 1.031,2.615 1.51,2.792 0.479,0.177 10 false CA2L

Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-35 (CA2H) - A41-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for LHD)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for RHD)

C

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CAN J/C LH)

12.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
a.
U183625E02
2.229,1.552 2.229,0.615 2.229,0.615 2.49,0.615 false 2.24,1.729 2.24,2.271 2.24,2.271 2.5,2.271 false 1.719,3.125 1.719,2.625 1.719,2.625 1.427,2.625 false 2.521,3.729 2.521,4.063 false 0.469,1.458 0.823,1.688 0.354,0.229 10 false G71 0.25,3.385 0.604,3.615 0.354,0.229 10 false G4 0.073,0.052 0.583,0.385 0.51,0.333 10 false *a 2.365,4.094 2.719,4.302 0.354,0.208 10 false BAT 1.135,2.542 1.427,2.76 0.292,0.219 10 false CG 2.542,0.531 3.125,0.75 0.583,0.219 10 false CANH*b 2.542,2.188 3.125,2.406 0.583,0.219 10 false CANL*b 0.094,2.229 0.604,2.563 0.51,0.333 10 false *1

Disconnect the G71 CAN junction connector LH (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G71-10 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power management control ECU
G71-21 (CANL) - G4-4 (CG)
G71-10 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Power management control ECU
G71-21 (CANL) - G4-16 (BAT)


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection. Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Power Management Control ECU



OK

13.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)

NG

14.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU - CAN J/C LH)
13.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
a.
U183626E02
1.427,1.552 1.427,0.615 1.427,0.615 2.208,0.615 false 1.438,1.719 1.438,2.094 1.438,2.094 2.219,2.094 false 1.719,3.135 1.719,2.635 1.719,2.635 1.427,2.635 false 2.51,3.74 2.51,4.073 false 1.208,1.542 1.208,0.604 1.208,0.604 0.938,0.604 false 1.208,1.708 1.208,2.094 1.208,2.094 0.969,2.094 false 0.479,1.458 0.833,1.688 0.354,0.229 10 false A51 0.25,3.406 0.604,3.635 0.354,0.229 10 false G4 0.083,0.063 0.594,0.396 0.51,0.333 10 false *a 2.365,4.094 2.719,4.302 0.354,0.208 10 false BAT 1.167,2.552 1.458,2.771 0.292,0.219 10 false CG 2.25,0.531 2.854,0.75 0.604,0.219 10 false CANH*c 2.26,2.01 2.833,2.229 0.573,0.219 10 false CANL*c 0.083,2.229 0.594,2.563 0.51,0.333 10 false *1 0.344,0.51 1.052,0.729 0.708,0.219 10 false CANH*b 0.396,2 1.104,2.219 0.708,0.219 10 false CANL*b

Disconnect the A51 CAN junction connector LH (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A51-1 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (skid control ECU)
A51-12 (CANL) - G4-4 (CG)
A51-3 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
A51-14 (CANL) - G4-4 (CG)
A51-1 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Brake booster with master cylinder assembly (skid control ECU)
A51-12 (CANL) - G4-16 (BAT)
A51-3 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A51-14 (CANL) - G4-16 (BAT)


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection. Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
*c to ECM

Result:
Result Proceed to
OK A
·

NG (Ground short in ECM CAN main bus line)

·

NG (+B short in ECM CAN main bus line)


B
·

NG (Ground short in brake booster with master cylinder assembly (skid control ECU) CAN branch line)

·

NG (+B short in brake booster with master cylinder assembly (skid control ECU) CAN branch line)


C




A

REPLACE CAN JUNCTION CONNECTOR LH

B

15.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN J/C LH)

C

16.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER - CAN J/C LH)
14.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU - CAN J/C LH)
a.

Disconnect the G57 power management control ECU connector.


b.
U183515E02
1.781,2.375 1.104,2.604 false 2.469,2.573 2.927,2.688 false 2.417,2.573 2.917,2.938 false 2.427,2.365 2.427,1.896 2.427,1.896 2.625,1.896 false 1.865,3 2.146,3.156 0.281,0.156 10 false G57 0.885,2.531 1.073,2.708 0.188,0.177 10 false E1 2.677,1.813 3.25,1.99 0.573,0.177 10 false AM21 2.948,2.896 3.323,3.073 0.375,0.177 10 false CA3P 2.958,2.635 3.344,2.813 0.385,0.177 10 false CA3N 0.104,0.083 0.542,0.417 0.438,0.333 10 false *a 2.531,2.99 2.813,3.146 0.281,0.156 10 false G58

Disconnect the G58 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-31 (CA3P) - G57-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G58-30 (CA3N) - G57-6 (E1)
G58-31 (CA3P) - G58-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G58-30 (CA3N) - G58-7 (AM21)


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection. Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - CAN J/C LH)

15.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN J/C LH)
a.
U183640E01
0.114,0.114 0.561,0.445 0.447,0.331 10 *a 2.69,0.517 3.191,0.707 0.501,0.190 10 CANP 2.69,2.072 3.153,2.262 0.463,0.190 10 CANN 0.475,0.517 0.976,0.707 0.501,0.190 10 BATT 0.727,2.896 1.011,3.085 0.284,0.190 10 E1 1.727,0.528 2.076,0.718 0.349,0.190 10 A40 2.43,2.963 2.746,3.153 0.316,0.190 10 C10 1.648,3.639 1.252,2.985 1.252,2.985 0.94,2.985 false 1.425,1.267 1.262,0.604 1.262,0.604 0.935,0.604 false 2.429,1.267 2.429,0.595 2.429,0.595 2.667,0.595 false 2.425,1.342 2.425,2.169 2.425,2.169 2.653,2.169 false 2.075,2.963 2.365,3.181 0.290,0.218 10 *A 1.662,2.963 1.979,3.153 0.316,0.190 10 C9 2.928,2.963 3.218,3.181 0.290,0.218 10 *B

Disconnect the 2 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-12 (CANP) - C9-16 (E1)*1
A40-12 (CANP) - C10-16 (E1)*2
Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-25 (CANN) - C9-16 (E1)*1
A40-25 (CANN) - C10-16 (E1)*2
A40-12 (CANP) - A40-1 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-25 (CANN) - A40-1 (BATT)


*1: for LHD

*2: for RHD

HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection. Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CAN J/C LH)

16.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER - CAN J/C LH)
a.
U183566E02
1.667,2.146 1.667,2.719 1.667,2.719 1.438,2.719 false 1.771,2.146 1.771,2.719 1.771,2.719 1.99,2.719 false 2.458,1.667 2.458,0.865 2.458,0.865 2.615,0.865 false 2.646,2.031 2.813,2.594 false 0.198,0.167 0.406,0.323 0.208,0.156 10 false *a 1.625,0.865 1.917,1.021 0.292,0.156 10 false A41 2.042,2.625 2.521,2.802 0.479,0.177 10 false CA2H 1.042,2.625 1.521,2.802 0.479,0.177 10 false CA2L 2.615,2.625 3,2.802 0.385,0.177 10 false GND 2.667,0.781 2.917,0.969 0.25,0.188 10 false BI

Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-35 (CA2H) - A41-28 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-34 (CA2L) - A41-28 (GND)
A41-35 (CA2H) - A41-14 (BI) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A41-34 (CA2L) - A41-14 (BI)


HINT:

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection. Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for LHD)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (for RHD)

C

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - CAN J/C LH)