There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω. | ·
Short in CAN main bus line ·
Short in CAN branch line ·
ECM ·
Brake booster with master cylinder assembly (Skid control ECU) ·
Main body ECU (Multiplex network body ECU) ·
Air conditioning amplifier assembly ·
Power steering ECU assembly ·
Smart key ECU assembly (Certification ECU) ·
Airbag sensor assembly ·
Spiral cable with sensor sub-assembly (Steering sensor) ·
Power management control ECU ·
Combination meter assembly ·
CAN junction connector LH ·
CAN junction connector RH |
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.
After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the G1 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-31 (CANH) - G1-32 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the combination meter assembly.
OK
NG
Reconnect the G1 combination meter assembly connector.
Disconnect the A40 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A40-13 (CANH) - A40-26 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
If the resistance becomes normal (between 108 to 132 Ω) when the connector is disconnected, there may be a short in the ECM.
OK
NG
Reconnect the A40 ECM connector.
Disconnect the G72 CAN junction connector RH.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G72-1 (CANH) - G72-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Spiral cable with sensor sub-assembly (Steering sensor) |
| G72-3 (CANH) - G72-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Smart key ECU assembly (Certification ECU) |
| G72-4 (CANH) - G72-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Airbag sensor assembly |
| G72-7 (CANH) - G72-18 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Combination meter assembly |
| G72-8 (CANH) - G72-19 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| G72-10 (CANH) - G72-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | CAN junction connector LH |
| *a | Front view of wire harness connector
(to CAN Junction Connector RH) |
| *b | to Spiral Cable with Sensor Sub-assembly (Steering Sensor) |
| *c | to Smart Key ECU Assembly (Certification ECU) |
| *d | to Airbag Sensor Assembly |
| *e | to Combination Meter Assembly |
| *f | to Air Conditioning Amplifier Assembly |
| *g | to CAN Junction Connector LH |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (CAN junction connector LH main line) | B |
| NG (ECU or sensor branch line) | C |
| NG (Combination meter assembly main line) | D |
A
B
C
D
Disconnect the G71 CAN junction connector LH (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| G71-1 (CANH) - G71-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Main body ECU (Multiplex network body ECU) |
| G71-2 (CANH) - G71-13 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Power steering ECU assembly |
| G71-3 (CANH) - G71-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher | DLC3 |
| G71-4 (CANH) - G71-15 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 1 MΩ or higher | CAN junction connector RH |
| G71-5 (CANH) - G71-16 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Power management control ECU |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side)) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
| *c | to Power Steering ECU Assembly |
| *d | to DLC3 |
| *e | to CAN Junction Connector RH |
| *f | to Power Management Control ECU |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (CAN junction connector RH main line) | B |
| NG (ECU or sensor branch line) | C |
| NG (DLC3 branch line) | D |
A
B
C
D
Disconnect the A51 CAN junction connector LH (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A51-9 (CANH) - A51-20 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| A51-10 (CANH) - A51-21 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder assembly (Skid control ECU) |
| *a | Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side)) |
| *b | to ECM |
| *c | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECM main line) | B |
| NG (ECU or sensor branch line) | C |
A
B
C
Reconnect all wire harness connectors (CAN junction connector LH and CAN junction connector RH).
Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G4-6 (CANH) - G4-14 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| *1 | DLC3 |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
OK
NG