Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM
RM2170E _58 Vehicle Interior _057034 DOOR LOCK _0278073 WIRELESS DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  No Answer-Back  


DESCRIPTION

In some cases, wireless door lock control functions are normal but the hazard warning light and/or wireless door lock buzzer answer-back function does not operate. In such cases, hazard warning light and wireless door lock buzzer signal outputs from the main body ECU (multiplex network body ECU) may be malfunctioning.

WIRING DIAGRAM

B281171E20
1.55,2.993 1.670,3.132 0.119,0.139 10 B 0.724,2.993 0.843,3.132 0.119,0.139 10 E 0.556,2.895 0.654,3.034 0.099,0.139 10 2 0.369,3.373 0.638,3.515 0.269,0.142 10 A28 1.734,2.895 1.846,3.034 0.112,0.139 10 1 0.369,3.55 2.073,3.692 1.704,0.142 10 Wireless Door Lock Buzzer 2.158,2.895 2.338,3.036 0.180,0.141 10 34 3.622,3 3.925,3.139 0.303,0.139 10 BZR 2.005,4.67 2.200,4.811 0.195,0.141 10 3C 2.79,3.801 3.021,3.942 0.231,0.141 10 MB 3.386,2.89 3.562,3.031 0.176,0.141 10 21 5.849,0.548 6.149,0.686 0.300,0.139 10 HAZ 3.244,0.46 3.344,0.598 0.100,0.138 10 1 2.79,3.974 4.437,4.286 1.647,0.312 10 Main Body ECU (Multiplex Network Body ECU) 2.005,4.839 4.652,4.983 2.647,0.143 10 Instrument Panel Junction Block Assembly 5.671,0.46 5.768,0.598 0.096,0.139 10 3 5.278,2.634 7.128,2.784 1.850,0.150 10 Combination Meter Assembly 0.753,5.462 2.451,5.604 1.698,0.142 10 : CAN Communication Line 3.144,1.158 4.592,1.473 1.448,0.314 10 Hazard Warning Signal Switch Assembly 4.51,0.46 4.610,0.598 0.100,0.138 10 4 3.144,1.023 3.360,1.161 0.217,0.139 10 G2 5.278,2.476 5.494,2.615 0.217,0.139 10 G3

CAUTION / NOTICE / HINT

NOTICE:

The wireless door lock control system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ANSWER-BACK OPERATION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Customize Setting / Wireless Door Lock.


e.

Select the setting by referring to the table below.

Display Default Content Setting Relevant ECU
Hazard Answer Back ON When the doors are locked by wireless operation, the hazard warning lights flash once.
When the doors are unlocked by wireless operation, the hazard warning lights flash twice.
OFF or ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Resp ON Wireless door lock buzzer response OFF or ON Main body ECU (Multiplex network body ECU)
Wireless Buzzer Vol Level 5*1
Level 7*2
Wireless door lock buzzer volume Level 7, Level 6, Level 5, Level 4, Level 3, Level 2, Level 1 or Level 0 Main body ECU (Multiplex network body ECU)

*1: w/ LED Headlight

*2: w/o LED Headlight


Result:
Result Proceed to
Both items are ON and not set to Level 0 A
Either item is OFF or set to Level 0 B




A

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS

B

2.CHECK WIRELESS DOOR LOCK CONTROL FUNCTIONS
a.

Check the wireless door lock control function using the electrical key transmitter sub-assembly.

Result:
Result Proceed to
Wireless door lock/unlock operates normally. A
Wireless door lock/unlock does not operate normally. B




A

3.READ VALUE USING INTELLIGENT TESTER (DOOR UNLOCK DETECTION SWITCH)

B

3.READ VALUE USING INTELLIGENT TESTER (DOOR UNLOCK DETECTION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Lock Pos Front door RH unlock detection switch signal/LOCK or UNLOCK LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FL Door Lock Pos Front door LH unlock detection switch signal/LOCK or UNLOCK LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
RR-Door Lock Pos SW*1 Rear door RH and LH unlock detection switch signal/ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
RL-Door Lock Pos SW*2 Rear door RH and LH unlock detection switch signal/ON or OFF ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-

·

*1: When checking RR-Door Lock Pos SW, make sure to check it with the rear door LH locked.

·

*2: When checking RL-Door Lock Pos SW, make sure to check it with the rear door RH locked.


OK:

The intelligent tester should display as shown in the table according to door lock operation.


Result:
Result Proceed to
OK A
NG (for Driver door) B
NG (for Front Passenger door) C
NG (for Rear LH door) D
NG (for Rear RH door) E




A

4.CHECK WIRELESS ANSWER-BACK OPERATION

B

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

C

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

D

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

E

GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit)

4.CHECK WIRELESS ANSWER-BACK OPERATION
a.

Check the wireless answer-back operation using the electrical key transmitter sub-assembly.

Result:
Result Proceed to
Only wireless door lock buzzer answer-back does not occur. A
Only hazard warning light answer-back does not occur. B




A

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER)

B

10.HAZARD WARNING LIGHTS OPERATION
5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WIRELESS DOOR LOCK BUZZER)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Test Part Control Range Diagnostic Note
Wireless Buzzer Wireless door lock buzzer OFF/ON -

Result:
Result Proceed to
Wireless door lock buzzer does not turn on/off. A
Wireless door lock buzzer turns on/off. B




A

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.CHECK HARNESS AND CONNECTOR (WIRELESS DOOR LOCK BUZZER - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the A28 wireless door lock buzzer and 3C instrument panel junction block assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-1 (B) - 3C-34 Always Below 1 Ω
A28-2 (E) - Body ground Always Below 1 Ω
A28-1 (B) - Body ground Always 10 kΩ or higher




OK

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U159159E02
5.563,1.167 5.802,1.51 false 0.167,0.063 0.354,0.25 0.188,0.188 10 false *a 1.313,0.385 1.604,0.563 0.292,0.177 10 false 3C 4.99,0.677 5.344,0.875 0.354,0.198 10 false MB 5.677,1.51 6.042,1.677 0.365,0.167 10 false BZR

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-34 - MB-21 (BZR) Always Below 1 Ω




OK

8.REPLACE WIRELESS DOOR LOCK BUZZER

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

8.REPLACE WIRELESS DOOR LOCK BUZZER
a.

Temporarily replace the wireless door lock buzzer with a new one (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK BUZZER>REMOVAL).



NEXT

9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
9.CHECK WIRELESS DOOR LOCK BUZZER OPERATION
a.

Check the operation of the wireless answer-back function.

OK:

Wireless answer-back function operates normally.




OK

END (WIRELESS DOOR LOCK BUZZER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

10.HAZARD WARNING LIGHTS OPERATION
a.

Check that the hazard warning light blinks when the hazard warning signal switch is pressed.

OK:

Hazard warning light signal is normal.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Hazard Warning Switch Circuit)