Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Entry Function) › 2014.12–2015.11
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278080 SMART ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate  


DESCRIPTION

When the entry operation and wireless operation of the door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (smart key ECU assembly) (the line used for entry and wireless operations); or 2) the electrical key transmitter sub-assembly. If the entry lock and wireless lock operations cannot be performed, there may be electrical key transmitter sub-assembly malfunctions, wave interference or problems in the communication which is used for the entry and wireless function between the door control receiver and certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B392604E02
5.292,0.885 5.708,1.063 0.417,0.177 10 false CUTB 3.969,1.073 4.833,1.25 0.865,0.177 10 false ECU-B NO. 1 2.198,0.917 3.583,1.094 1.385,0.177 10 false from Auxiliary Battery 4.896,0.927 5.208,1.104 0.313,0.177 10 false G77 4.958,0.729 5.135,0.906 0.177,0.177 10 false 10 5.292,2.479 5.729,2.656 0.438,0.177 10 false RDAS 4.969,2.344 5.146,2.521 0.177,0.177 10 false 17 5.292,2.875 5.708,3.052 0.417,0.177 10 false RSSI 4.969,2.719 5.146,2.896 0.177,0.177 10 false 19 5.292,3.26 5.708,3.438 0.417,0.177 10 false E 4.979,3.604 6.521,3.969 1.542,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.823,3.573 1.188,3.75 0.365,0.177 10 false M15 0.823,3.729 2.281,3.906 1.458,0.177 10 false Door Control Receiver 4.969,3.115 5.146,3.292 0.177,0.177 10 false 11 5.292,1.292 5.521,1.469 0.229,0.177 10 false +B 5,1.135 5.104,1.313 0.104,0.177 10 false 2 5.292,2.104 5.635,2.281 0.344,0.177 10 false RCO 1.823,2.146 2,2.323 0.177,0.177 10 false +5 2.115,2 2.292,2.177 0.177,0.177 10 false 4 1.635,2.521 2.031,2.698 0.396,0.177 10 false DATA 2.115,2.375 2.292,2.552 0.177,0.177 10 false 5 2.115,2.75 2.292,2.927 0.177,0.177 10 false 2 1.677,3.208 2.052,3.385 0.375,0.177 10 false GND 2.115,3.083 2.292,3.26 0.177,0.177 10 false 1 5.01,1.927 5.188,2.104 0.177,0.177 10 false 5 1.656,2.896 2.073,3.073 0.417,0.177 10 false RSSI 2.146,1.729 3.542,2.115 1.396,0.385 10 false from IG2 Relay Circuit 5.292,1.688 5.708,1.865 0.417,0.177 10 false IG 5,1.531 5.177,1.708 0.177,0.177 10 false 5 4.281,1.479 4.708,1.656 0.427,0.177 10 false AM2 4.906,1.323 5.219,1.5 0.313,0.177 10 false G77 4.896,1.729 5.208,1.906 0.313,0.177 10 false G79 4.906,2.146 5.219,2.323 0.313,0.177 10 false G78 4.906,2.521 5.219,2.698 0.313,0.177 10 false G78 4.906,2.885 5.219,3.063 0.313,0.177 10 false G78 4.917,3.281 5.229,3.458 0.313,0.177 10 false G77

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the CAN communication system and LIN communication system. First inspect the communication systems by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the power switch off to troubleshoot:

Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>B1242).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart entry and start system (for Entry Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The door control receiver has a constant voltage (5 V) supply circuit connected to terminal "+5".



PROCEDURE

1.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the voltage of the vehicle auxiliary battery.

Standard voltage:

11 to 14 V (IG OFF)


HINT:

It may be possible to tell whether the vehicle auxiliary battery is discharged by operating the horn.


If the voltage is below 11 V, recharge or replace the vehicle auxiliary battery before proceeding.




NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Open the driver door using the mechanical key built into the electrical key transmitter sub-assembly.


b.

Connect the intelligent tester and check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).

HINT:

When using the intelligent tester with the power switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.


OK:

DTC is not output.




OK

3.CHECK POWER DOOR LOCK CONTROL SYSTEM

NG

3.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly on the driver door is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

4.CHECK KEY DIAGNOSTIC MODE

NG

4.CHECK KEY DIAGNOSTIC MODE
a.

Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

i.
B300377E02
2.354,1.167 2.563,1.354 0.208,0.188 10 false *a 1.26,3.479 1.469,3.667 0.208,0.188 10 false *a 0.125,0.083 0.542,0.49 0.417,0.406 10 true *A 0.177,2.302 0.75,2.458 0.573,0.156 10 false *B

Check the electrical key antenna (for driver door):

Text in Illustration
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for driver door), check that the wireless door lock buzzer sounds.


ii.
B300378E02
1.313,1.219 1.521,1.406 0.208,0.188 10 false *a 2.344,3.479 2.552,3.667 0.208,0.188 10 false *a 0.083,0.083 0.667,0.51 0.583,0.427 10 true *A 0.104,2.135 0.677,2.292 0.573,0.156 10 false *B

Check the electrical key antenna (for front passenger door):

Text in Illustration
*A for LHD
*B for RHD
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the front door outside handle assembly (for front passenger door), check that the wireless door lock buzzer sounds.


iii.
B296517E01
2.524,0.398 2.772,0.567 0.248,0.170 10 *a 1.75,1.219 2.33,0.481 2.33,0.481 2.491,0.481 false

Check the No. 1 indoor electrical key antenna (front floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


iv.
B300410E02
0.938,1.156 2.354,1.865 2.354,1.865 2.531,1.865 false 1.646,3.438 2.385,4.094 2.385,4.094 2.563,4.094 false 2.573,1.771 2.802,1.99 0.229,0.219 10 false *a 0.094,0.083 0.375,0.25 0.281,0.167 10 false *A 0.094,2.323 0.375,2.49 0.281,0.167 10 false *B 2.604,4.01 2.833,4.229 0.229,0.219 10 false *a

Check the No. 2 indoor electrical key antenna (steering column):

Text in Illustration
*A for LHD
*B for RHD
*a Inspection Point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


v.
B296518E01
2.456,0.23 2.704,0.400 0.248,0.170 10 *a 1.809,0.68 2.29,0.325 2.29,0.325 2.423,0.325 false

Check the No. 3 indoor electrical key antenna (rear floor):

Text in Illustration
*a Inspection Point

When the electrical key transmitter sub-assembly is at the inspection point, check that the wireless door lock buzzer sounds.


vi.
B296538E02
1.792,1.318 2.041,1.488 0.248,0.170 10 *a

Check the electrical key antenna (outside luggage):

Text in Illustration
*a 0.7 to 1 m (2.30 to 3.28 ft.)

When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.


Result:
Result Proceed to
Diagnostic mode inspections fail A
Diagnostic mode inspections succeed B





A

5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

10.CHECK WAVE ENVIRONMENT
5.CHECK ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY
a.

Check if there are any other registered electrical key transmitter sub-assemblies.

Result:
Result Proceed to
There are no other registered electrical key transmitter sub-assemblies A
There is another registered electrical key transmitter sub-assemblies B




A

6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)

B

7.CHECK ENTRY DOOR LOCK OPERATION
6.ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY REGISTRATION (NEW ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY)
a.

Register a new electrical key transmitter sub-assembly.

HINT:

Refer to the Service Bulletin.




NEXT

7.CHECK ENTRY DOOR LOCK OPERATION
7.CHECK ENTRY DOOR LOCK OPERATION
a.

Using another or newly registered electrical key transmitter sub-assembly, check if an entry lock/unlock operation can be performed twice in succession.

OK:

Entry lock/unlock operate normally twice.




OK

8.CHECK TRANSMITTER BATTERY

NG

10.CHECK WAVE ENVIRONMENT
8.CHECK TRANSMITTER BATTERY
a.

Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.

i.

Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.

Result:
Result Proceed to
Transmitter LED does not illuminate when switch is pressed and held A
Transmitter LED illuminates 3 times or more when switch is pressed and held B
Transmitter LED illuminates once or twice but not a third time C


HINT:
·

The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).

·

Even if the transmitter battery is depleted, it is still possible to start the hybrid system by holding the electrical key transmitter sub-assembly against the power switch, depressing the brake pedal and pressing the power switch.






A

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)

B

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

C

REPLACE TRANSMITTER BATTERY

9.INSPECT TRANSMITTER BATTERY (VOLTAGE)
a.

Inspect the transmitter battery

i.
B197599E01
2.023,0.142 2.230,0.326 0.207,0.184 10 *1 1.788,1.049 1.788,0.218 1.788,0.218 1.977,0.218 false

Remove the transmitter battery from the electrical key transmitter sub-assembly that does not operate (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).


ii.

Attach a lead wire (0.60 mm (0.0236 in.) in diameter or less including wire sheath) with tape or equivalent to the negative terminal.

Text in Illustration
*1 Lead Wire

NOTICE:

Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.



iii.

Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.


iv.
B269082E01
1.639,0.39 1.846,0.573 0.207,0.184 10 *1 1.152,0.479 1.558,0.479 false

Measure the voltage of the transmitter battery.

HINT:
·

When measuring the transmitter battery voltage, bring the electrical key transmitter sub-assembly within the lock entry operating range while operating the lock sensor of a door handle to perform the measurement.

·

Perform the measurement when the key is at room temperature.

·

The key sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. When this voltage is 2.2 V or less the Data List item "Key Low Battery" displays "Yes". (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST)



Text in Illustration
*1 GND

Standard Voltage:
Tester Connection Condition Specified Condition
Transmitter battery positive (+) - Transmitter battery negative (-) Power switch off, all doors closed and lock sensor touched 2.3 to 3.2 V





OK

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

NG

REPLACE TRANSMITTER BATTERY

10.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter sub-assembly near the door control receiver and perform a wireless and entry function operation check.

HINT:
·

When the electrical key transmitter sub-assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

·

There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.

·

If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.



OK:

Wireless and entry functions operate normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

11.READ VALUE USING INTELLIGENT TESTER (ACC SW, IG SW)
11.READ VALUE USING INTELLIGENT TESTER (ACC SW, IG SW)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ACC SW Power switch status / ON or OFF ON: Power switch on (ACC)
OFF: Power switch off
-
IG SW Power switch status / ON or OFF ON: Power switch to ON
OFF: Power switch off
-

HINT:

If the certification ECU (smart key ECU assembly) misjudges that the power source is on even though the power source is off for any reason, the entry lock/unlock functions stop.


OK:

The main body ECU (multiplex network body ECU) judges properly that the power source is off when the power source is off.



OK

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)

NG

12.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - AUXILIARY BATTERY AND BODY GROUND)
a.
U183394E02
1.135,1.271 0.833,1.771 false 2.302,1.135 2.792,1.771 false 2.313,0.979 2.76,0.76 false 1.563,0.198 1.875,0.375 0.313,0.177 10 false G77 0.156,0.073 0.438,0.25 0.281,0.177 10 false *a 0.75,1.792 0.865,1.969 0.115,0.177 10 false E 2.802,0.656 3.156,0.833 0.354,0.177 10 false +B 2.604,1.792 3.042,1.969 0.438,0.177 10 false CUTB

Disconnect the G77 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G77-11 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G77-10 (CUTB) - Body ground Always 11 to 14 V
G77-2 (+B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER)
a.

Disconnect the G78 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the M15 door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
G78-5 (RCO) - M15-4 (+5) Always Below 1 Ω
G78-17 (RDAS) - M15-5 (DATA) Always Below 1 Ω
G78-19 (RSSI) - M15-2 (RSSI) Always Below 1 Ω
G78-5 (RCO) or M15-4 (+5) - Body ground Always 10 kΩ or higher
G78-17 (RDAS) or M15-5 (DATA) - Body ground Always 10 kΩ or higher
G78-19 (RSSI) or M15-2 (RSSI) - Body ground Always 10 kΩ or higher



OK

14.CHECK DOOR CONTROL RECEIVER (GND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK DOOR CONTROL RECEIVER (GND)
a.
U183397E02
2.042,1.115 2.333,1.74 false 0.24,0.115 0.448,0.313 0.208,0.198 10 false *a 2.208,1.75 2.625,1.948 0.417,0.198 10 false GND 0.667,0.792 0.99,0.99 0.323,0.198 10 false M15

Connect the M15 door control receiver connector.


b.

Connect the G78 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M15-1 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Door Control Receiver)



OK

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

15.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the G78 certification ECU (smart key ECU assembly) connector.


b.

Connect the M15 door control receiver connector.


c.

Measure the voltage according to the value(s) in the table below.


U183398E02
2.042,1.115 2.333,1.74 false 1.531,1.125 1.24,1.75 false 0.24,0.115 0.448,0.313 0.208,0.198 10 false *a 0.594,0.646 0.885,0.844 0.292,0.198 10 false M15 2.188,1.76 2.604,1.958 0.417,0.198 10 false GND 1.135,1.771 1.344,1.958 0.208,0.188 10 false +5

Standard Voltage:
Tester Connection Condition Specified Condition
M15-4 (+5) - M15-1 (GND) Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly switch not pressed


Below 1 V
Procedure:
1.

Power switch off

2.

Electrical key transmitter sub-assembly switch pressed


4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(Door Control Receiver)


OK

16.CHECK DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

16.CHECK DOOR CONTROL RECEIVER
a.

Connect the G78 certification ECU (smart key ECU assembly) connector.


b.

Connect the M15 door control receiver connector.


c.

Measure the voltage according to the value(s) in the table below.


U183399E01
0.269,0.203 0.481,0.405 0.211,0.202 10 *a 0.582,0.621 0.960,0.768 0.378,0.147 10 M15 2.541,1.592 2.940,1.753 0.399,0.161 10 GND 2.071,1.103 2.746,1.594 false 0.762,1.605 1.175,1.759 0.413,0.154 10 DATA 1.384,1.103 0.954,1.59 false 1.941,1.605 2.340,1.765 0.399,0.161 10 RSSI 1.908,1.113 2.166,1.604 false

Standard Voltage:
Tester Connection Condition Specified Condition
M15-5 (DATA) - M15-1 (GND) Procedure:
1.

All doors closed

2.

All doors locked

3.

Electrical key transmitter sub-assembly switch pressed


Below 2 V → 11 to 14 V → Below 2 V
M15-2 (RSSI) - M15-1 (GND) Procedure:
1.

Power switch off

2.

All doors closed


11 to 14 V → Below 2 V


Text in Illustration
*a Component with harness connected
(Door Control Receiver)


OK

17.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE DOOR CONTROL RECEIVER

17.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Temporarily replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.




NEXT

18.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
18.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check that the wireless door lock functions operate normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Wireless door lock functions operate normally.




OK

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)