If any of the following operations are performed, the power management control ECU receives a signal, and changes the power source mode.
With the electrical key transmitter sub-assembly in the cabin, the power switch is pressed.
When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.
When the smart entry and start system cancel function has been canceled on the customization menu, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
for Power Source Control: Body / Power Source Control / DTC.
for Entry&Start: Body / Entry&Start / DTC.
The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the electrical key transmitter sub-assembly, refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>PRECAUTION).
Before replacing the power management control ECU, refer to the Service Bulletin.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).
If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After completing repairs, confirm that the problem does not occur.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
Power Supply Condition ·
IG1 Relay Monitor(Inside) ·
IG2 Relay Monitor(Inside) ·
IG1 Relay Monitor(Outside) ·
IG2 Relay Monitor(Outside) ·
Latch Circuit ·
ACC Relay Monitor |
- |
Check the wireless door lock function by operating the electrical key transmitter sub-assembly.
Wireless door lock function operates.
OK
NG
OK
NG
OK
NG
Remove the transmitter battery from the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY>REPLACEMENT).
With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.
The power source mode changes.
If the power source mode changes, the cabin verification is malfunctioning.
| Result | Proceed to |
|---|---|
| The power source mode does not change. | A |
| The power source mode changes. | B |
| *1 | Power Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
A
B
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Specified Condition |
|---|---|---|---|
| Stop Light Switch1 | State of brake pedal/ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
·
Use this item to determine whether the stop light switch is malfunctioning. ·
The hybrid control system cannot be started when this item is OFF. ·
When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time. |
ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.
OK
NG
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Power Supply Condition | Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Power switch off
ACC ON: Power switch on (ACC) IG1 ON: Power switch on (IG) (IG1 relay on) IG2 ON: Power switch on (IG) (IG2 relay on) ST ON: Sending hybrid control system start request signal |
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
With the power switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch for 2 seconds or more and read the Data List.
IG2 ON is displayed in the Data List.
If the smart entry and start system function has been canceled on the customization menu, ACC ON is displayed in the Data List.
OK
NG
Read the Data List according to the display on the intelligent tester.
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Power Management Control ECU) |
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Power Supply Condition | Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON | All OFF: Power switch off
ACC ON: Power switch on (ACC) IG1 ON: Power switch on (IG) (IG1 relay on) IG2 ON: Power switch on (IG) (IG2 relay on) ST ON: Sending hybrid control system start request signal |
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time). |
Measure the voltage while checking the Data List on the intelligent tester.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G58-2 (IG1D) - Body ground | Power switch off | 1 V or less |
| Power switch on (ACC) | 1 V or less | |
| Power switch on (IG) | 9 V or higher | |
| A39-2 (IG2D) - Body ground | Power switch off | 1 V or less |
| Power switch on (ACC) | 1 V or less | |
| Power switch on (IG) | 9 V or higher | |
| G58-1 (ACCD) - Body ground | Power switch off | 1 V or less |
| Power switch on (IG) | 8.5 V or higher | |
| Power switch on (ACC) | 8.5 V or higher |
OK
NG
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Start Switch1 | Power switch 1 status/ON or OFF | ON: Power switch pressed
OFF: Power switch not pressed |
·
If the power switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the power switch input signal is malfunctioning. |
| Start Switch2 | Power switch 2 status/ON or OFF | ON: Power switch pressed
OFF: Power switch not pressed |
·
Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal. ·
Behaves the same way as power switch 1. |
ON (Power switch is pressed) and OFF (Power switch is not pressed) appear on the screen.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Inspect the power switch (See page Engine / Hybrid System>1NZ-FXE STARTING>POWER SWITCH>INSPECTION).
OK
NG
Disconnect the G57 and G58 connectors from the power management control ECU.
Disconnect the G48 connector from the power switch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G57-7 (SSW1) - G48-5 (SS1) | Always | Below 1 Ω |
| G58-17 (SSW2) - G48-1 (SS2) | Always | Below 1 Ω |
| G57-7 (SSW1) or G48-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| G58-17 (SSW2) or G48-1 (SS2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the A32 connector from stop light switch assembly.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32-7 (B) - A32-2 (GND) | Power switch off | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A32-2 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
OK
NG
Reconnect the A32 connector from stop light switch assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A32-3 (L) - A32-2 (GND) | Power switch off, Brake pedal not depressed | Below 1 V |
| A32-3 (L) - A32-2 (GND) | Power switch off, Brake pedal depressed | 11 to 14 V |
| *a | Component with harness connected
(Stop Light Switch Assembly) |
OK
NG
OK
NG
Enter the following menus:
for Entry&Start: Body / Entry&Start / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| The following DTCs are not output:
·
B2785 ·
B2287 ·
B2784 ·
B278A |
A |
| DTC B2785 is not output but DTC B2287 is output. | B |
| DTCs other than B2287 are output. | C |
A
B
C