Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function) › 2013.12–2014.12
RM2170E _58 Vehicle Interior _057035 THEFT DETERRENT / KEYLESS ENTRY _0278081 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the power management control ECU receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B309715E01
4.964,6.67 5.217,6.826 0.253,0.156 10 IG2 4.493,7.037 6.279,7.235 1.786,0.199 10 No. 1 Integration Relay 2.707,1.059 3.054,1.208 0.347,0.149 10 IG1D 2.712,6.359 3.058,6.508 0.347,0.149 10 IG2D 0.287,7.094 0.995,7.243 0.708,0.149 10 *1: for LHD 0.287,7.444 1.037,7.593 0.750,0.149 10 *2: for RHD 3.716,5.103 6.384,5.252 2.669,0.149 10 Instrument Panel Junction Block Assembly 2.036,6.893 3.302,7.257 1.266,0.364 10 Power Management Control ECU 4.743,4.541 5.437,4.690 0.694,0.149 10 IG1 NO. 3 4.743,2.966 5.437,3.115 0.694,0.149 10 IG1 NO. 2 4.743,1.379 5.437,1.528 0.694,0.149 10 IG1 NO. 1 3.187,6.172 3.297,6.318 0.111,0.145 10 2 3.225,0.879 3.335,1.024 0.111,0.145 10 2 3.116,1.059 3.446,1.250 0.330,0.191 10 G58 3.117,6.354 3.447,6.545 0.330,0.191 10 A39 4.256,6.351 4.558,6.507 0.302,0.156 10 2D 5.981,6.355 6.263,6.511 0.282,0.156 10 2D 4.303,6.18 4.486,6.336 0.184,0.156 10 3 6.024,6.179 6.208,6.335 0.184,0.156 10 2 3.676,0.643 3.931,0.834 0.254,0.191 10 3E 3.678,1.059 3.933,1.250 0.254,0.191 10 3A 3.693,0.885 3.898,1.030 0.205,0.145 10 29 6.294,0.648 6.548,0.839 0.254,0.191 10 3A 6.305,0.474 6.542,0.619 0.237,0.145 10 54 6.299,2.229 6.553,2.419 0.254,0.191 10 3A 6.349,2.055 6.554,2.200 0.205,0.145 10 9 6.294,4.222 6.548,4.413 0.254,0.191 10 3B 6.337,4.048 6.541,4.193 0.205,0.145 10 8 5.753,2.369 6.262,2.524 0.509,0.155 10 WIPER 5.745,0.793 6.289,1.136 0.544,0.343 10 ECU-IG NO. 1 3.651,0.459 3.879,0.604 0.227,0.145 10 1*1 3.999,0.643 4.253,0.834 0.254,0.191 10 3F 3.974,0.459 4.204,0.604 0.231,0.145 10 1*2 0.087,1.581 0.991,2.055 0.904,0.473 10 from Auxiliary Battery 1.234,1.745 1.564,1.936 0.330,0.191 10 AM2 2.29,1.59 2.730,1.739 0.441,0.149 10 AM21 2.009,1.411 2.120,1.557 0.111,0.145 10 7 1.926,1.59 2.211,1.780 0.285,0.191 10 G58 2.29,1.99 2.730,2.139 0.441,0.149 10 AM22 2.009,1.804 2.120,1.949 0.111,0.145 10 1 1.926,1.99 2.212,2.180 0.286,0.191 10 G57 2.29,3.988 2.730,4.137 0.441,0.149 10 E01 2.021,3.811 2.132,3.956 0.111,0.145 10 5 1.926,3.988 2.212,4.179 0.286,0.191 10 G57 2.297,4.388 2.737,4.537 0.441,0.149 10 E02 2.028,4.21 2.139,4.356 0.111,0.145 10 5 1.926,4.388 2.212,4.578 0.286,0.191 10 G58 2.276,4.866 2.716,5.015 0.441,0.149 10 E1 2.019,4.679 2.130,4.825 0.111,0.145 10 6 1.926,4.866 2.212,5.056 0.286,0.191 10 G57 5.552,6.068 5.806,6.224 0.253,0.156 10 IG2 4.251,5.925 4.552,6.081 0.302,0.156 10 2D 4.301,5.762 4.484,5.918 0.184,0.156 10 4 5.981,5.936 6.282,6.092 0.302,0.156 10 2E 6.031,5.761 6.214,5.917 0.184,0.156 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

IG1 Relay Monitor (Outside)

·

IG2 Relay Monitor (Outside)

·

IG1 Circuit

·

IG2 Circuit


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the A39 connector from the power management control ECU.


b.

Disconnect the 2D and 2E connectors from the No. 1 integration relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-2 (IG2D) - 2D-3 Always Below 1 Ω
2D-2 - Body ground Always Below 1 Ω
A39-2 (IG2D) or 2D-3 - Body ground Always 10 kΩ or higher




OK

2.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Remove the No. 1 integration relay (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>REMOVAL).


b.


OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G58 connector from the power management control ECU.


b.

Disconnect the 3A and 3B connectors from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-2 (IG1D) - 3A-29 Always Below 1 Ω
3B-8 - Body ground Always Below 1 Ω
G58-2 (IG1D) and 3A-29 - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1 IND IG1 NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1 IND IG1 NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

U183392E02
5.146,0.906 5.469,1.125 0.323,0.219 10 false 3F 5.438,0.917 5.594,1.073 0.156,0.156 10 false *2 5.135,0.604 5.458,0.823 0.323,0.219 10 false 3E 5.427,0.594 5.583,0.75 0.156,0.156 10 false *1 2.115,0.177 2.438,0.396 0.323,0.219 10 false 3A 2.146,1.49 2.469,1.708 0.323,0.219 10 false 3B 0.188,0.073 0.438,0.292 0.25,0.219 10 false *a

Text in Illustration
*1 for LHD *2 for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
·

3E-1 - 3A-54

(IG1 No. 1 relay)

·

3E-1 - 3A-9

(IG1 No. 2 relay)


Auxiliary battery voltage not applied to terminals 3A-29 and 3B-8 10 kΩ or higher
Auxiliary battery voltage applied to terminals 3A-29 and 3B-8 Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
·

3F-1 - 3A-54

(IG1 No. 1 relay)

·

3F-1 - 3A-9

(IG1 No. 2 relay)


Auxiliary battery voltage not applied to terminals 3A-29 and 3B-8 10 kΩ or higher
Auxiliary battery voltage applied to terminals 3A-29 and 3B-8 Below 1 Ω




OK

5.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK POWER MANAGEMENT CONTROL ECU
a.

Reconnect the A39 and G58 power management control ECU connectors.


b.

Measure the voltage according to the value(s) in the table below.


U183361E01
0.057,0.047 0.210,0.183 0.153,0.136 10 *a 1.29,0.456 1.555,0.595 0.265,0.139 10 A39 2.511,0.456 2.793,0.595 0.283,0.139 10 G58 1.29,1.893 1.642,2.032 0.353,0.139 10 IG2D 2.528,1.893 2.877,2.032 0.349,0.139 10 IG1D 1.6,1.133 1.495,1.9 false 2.733,1.902 2.785,1.132 false

Standard Voltage:
Tester Connection Condition Specified Condition
A39-2 (IG2D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
G58-2 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG