If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
for Power Source Control: Body / Power Source Control / DTC.
for Entry&Start: Body / Entry&Start / DTC.
The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).
If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After completing repairs, confirm that the problem does not occur.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) but does change to on (ACC) | Power Source Control
·
Power Supply Condition ·
IG1 Relay Monitor (Inside) ·
IG2 Relay Monitor (Inside) ·
IG1 Relay Monitor (Outside) ·
IG2 Relay Monitor (Outside) ·
IG1 Circuit ·
IG2 Circuit |
- |
Disconnect the G77 connector from the certification ECU (smart key ECU assembly).
Disconnect the 2D connector from the No. 1 integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-9 (IG2D) - 2D-3 | Always | Below 1 Ω |
| 2D-2 - Body ground | Always | Below 1 Ω |
| G77-9 (IG2D) or 2D-3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the No. 1 integration relay (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>REMOVAL).
Inspect the No. 1 integration relay (See page Engine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>INTEGRATION RELAY>INSPECTION).
OK
NG
Disconnect the G79 connector from the certification ECU (smart key ECU assembly).
Disconnect the 3A and 3B connectors from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G79-6 (IG1D) - 3A-29 | Always | Below 1 Ω |
| 3B-8 - Body ground | Always | Below 1 Ω |
| G79-6 (IG1D) and 3A-29 - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| *1 | for LHD | *2 | for RHD |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
·
3E-1 - 3A-54 (IG1 No. 1 relay) ·
3E-1 - 3A-9 (IG1 No. 2 relay) |
Auxiliary battery voltage not applied to terminals 3A-29 and 3B-8 | 10 kΩ or higher |
| Auxiliary battery voltage applied to terminals 3A-29 and 3B-8 | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
·
3F-1 - 3A-54 (IG1 No. 1 relay) ·
3F-1 - 3A-9 (IG1 No. 2 relay) |
Auxiliary battery voltage not applied to terminals 3A-29 and 3B-8 | 10 kΩ or higher |
| Auxiliary battery voltage applied to terminals 3A-29 and 3B-8 | Below 1 Ω |
OK
NG
Reconnect the G77 and G79 certification ECU (smart key ECU assembly) connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G77-9 (IG2D) - Body ground | Power switch on (ACC) → Power switch on (IG) | 1 V or less → 9 V or higher |
| G79-6 (IG1D) - Body ground | Power switch on (ACC) → Power switch on (IG) | 1 V or less → 9 V or higher |
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
OK
NG