Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057036 LIGHTING (INT) _0278087 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Personal Light


HINT:

The DOME CUT relay supplies power to the lights not controlled by the illuminated entry system. If all the lights that use power from the DOME CUT relay do not turn on, check the DOME CUT relay circuit first (See page Vehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE).


WIRING DIAGRAM

E227114E02
5.884,2.953 7.044,3.567 1.160,0.614 10 Main Body ECU (Multiplex Network Body ECU) 0.496,3.61 1.783,3.784 1.287,0.174 10 Q1 0.496,3.769 2.276,3.943 1.780,0.174 10 Map Light Assembly 3.254,1.033 3.549,1.208 0.295,0.174 10 OFF 0.824,3.137 2.539,3.329 1.716,0.192 10 Personal Light Switch LH 3.31,1.683 3.535,1.858 0.226,0.174 10 ON 1.688,2.476 1.983,2.651 0.295,0.174 10 OFF 1.758,2.893 1.983,3.068 0.226,0.174 10 ON 1.676,1.269 1.971,1.443 0.295,0.174 10 OFF 1.746,1.692 1.971,1.866 0.226,0.174 10 ON 2.907,1.907 3.746,2.324 0.839,0.418 10 Interior Light Door Switch 4.192,1.285 4.366,1.460 0.174,0.174 10 2 3.841,1.285 4.137,1.460 0.296,0.174 10 CTY 5.84,1.175 5.936,1.349 0.096,0.174 10 1 5.774,1.358 6.001,1.533 0.226,0.174 10 MB 3.813,3.404 4.007,3.579 0.195,0.174 10 E 0.41,1.402 0.605,1.577 0.195,0.174 10 B 4.722,1.173 4.897,1.347 0.175,0.174 10 6 4.674,1.356 4.861,1.530 0.187,0.174 10 3B 3.813,3.587 3.988,3.761 0.175,0.174 10 1 6.145,1.362 6.439,1.537 0.294,0.174 10 ILE 4.61,1.717 5.857,2.355 1.246,0.637 10 Instrument Panel Junction Block Assembly 0.824,1.939 2.470,2.145 1.646,0.205 10 Personal Light Switch RH 3.305,1.281 3.821,1.441 0.516,0.161 10 DOOR 0.27,1.402 0.409,1.565 0.139,0.163 10 3 0.894,0.286 2.723,0.540 1.829,0.254 10 from DOME CUT Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Check that the lights operate.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Illuminated Entry System Personal light ON/OFF Interior light door switch DOOR

OK:

Each light fades in.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).


b.

Inspect the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION).

OK:

Map light assembly is normal.




OK

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q1-2 (CTY) - 3B-6 Always Below 1 Ω
Q1-2 (CTY) - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U114311E01
0.157,0.099 0.313,0.245 0.156,0.145 10 *a 1.21,0.36 1.406,0.505 0.195,0.145 10 3B 4.69,0.36 4.938,0.526 0.248,0.166 10 MB 3.138,1.4 3.369,1.545 0.231,0.145 10 ILE 3.013,1.113 3.013,1.472 3.013,1.472 3.113,1.472 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3B-6 - MB-1 (ILE) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY