Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2014.12
RM2170E _58 Vehicle Interior _057036 LIGHTING (INT) _0278087 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Personal Light

·

Rear Dome Light (w/ Rear Dome Light)


HINT:

The DOME CUT relay supplies power to the lights not controlled by the illuminated entry system. If all the lights that use power from the DOME CUT relay do not turn on, check the DOME CUT relay circuit first (See page Vehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE).


WIRING DIAGRAM

E309640E04
5.927,2.708 7.083,3.323 1.156,0.615 10 false Main Body ECU (Multiplex Network Body ECU) 0.542,3.417 1.833,3.594 1.292,0.177 10 false Q1 0.542,3.583 2.323,3.76 1.781,0.177 10 false Map Light Assembly 3.302,0.844 3.594,1.021 0.292,0.177 10 false OFF 0.875,2.938 2.594,3.125 1.719,0.188 10 false Personal Light Switch LH 3.354,1.479 3.583,1.656 0.229,0.177 10 false ON 1.708,2.219 2,2.396 0.292,0.177 10 false OFF 1.771,2.677 2,2.854 0.229,0.177 10 false ON 1.708,1.052 2,1.229 0.292,0.177 10 false OFF 1.781,1.51 2.01,1.688 0.229,0.177 10 false ON 2.958,1.719 3.802,2.135 0.844,0.417 10 false Interior Light Door Switch 4.208,1.063 4.385,1.24 0.177,0.177 10 false 2 3.865,1.073 4.156,1.25 0.292,0.177 10 false CTY 5.854,0.979 5.948,1.156 0.094,0.177 10 false 1 5.802,1.177 6.031,1.354 0.229,0.177 10 false MB 3.833,3.198 4.031,3.375 0.198,0.177 10 false E 0.427,1.198 0.625,1.375 0.198,0.177 10 false B 4.74,0.979 4.917,1.156 0.177,0.177 10 false 6 4.688,1.167 4.875,1.344 0.188,0.177 10 false 3B 3.844,3.427 4.021,3.604 0.177,0.177 10 false 1 6.188,1.167 6.479,1.344 0.292,0.177 10 false ILE 4.656,1.521 5.969,2.156 1.313,0.635 10 false Instrument Panel Junction Block Assembly 0.875,1.76 2.521,1.969 1.646,0.208 10 false Personal Light Switch RH 3.323,1.052 3.844,1.208 0.521,0.156 10 false DOOR 0.271,1.208 0.406,1.375 0.135,0.167 10 false 3 0.938,0.094 2.771,0.344 1.833,0.25 10 false from DOME CUT Relay 3.771,4.552 3.948,4.729 0.177,0.177 10 false 2 3.771,4.146 3.906,4.313 0.135,0.167 10 false 3 3.583,4.552 3.781,4.729 0.198,0.177 10 false E 3.417,4.302 3.708,4.479 0.292,0.177 10 false CTY 2.813,4.677 3.177,4.854 0.365,0.177 10 false OFF 2.813,4.906 3.094,5.083 0.281,0.177 10 false ON 2.781,4.271 3.302,4.427 0.521,0.156 10 false DOOR 1.458,4.5 1.656,4.677 0.198,0.177 10 false B 1.292,4.5 1.427,4.667 0.135,0.167 10 false 1 1.427,5.177 2.719,5.354 1.292,0.177 10 false Q6 1.427,5.344 3.594,5.521 2.167,0.177 10 false No. 1 Room Light Assembly* 1.5,4.781 2.76,5.083 1.26,0.302 10 false Rear Dome Light 4.406,3.75 4.542,3.917 0.135,0.167 10 false * 0.229,3.99 0.365,4.156 0.135,0.167 10 false * 4.115,4.771 4.25,4.938 0.135,0.167 10 false * 5.021,5.24 6.917,5.542 1.896,0.302 10 false *: w/ Rear Dome Light

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.


f.

Check that the lights operate.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Illuminated Entry System Personal light and rear dome light* ON/OFF Interior light door switch DOOR

*: w/ Rear Dome Light


OK:

Each light fades in.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).


b.

Inspect the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION).

OK:

Map light assembly is normal.



Result
Result Proceed to
OK (w/ Rear Dome Light) A
OK (w/o Rear Dome Light) B
NG C


A

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - NO. 1 ROOM LIGHT ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAP LIGHT ASSEMBLY)

C

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - NO. 1 ROOM LIGHT ASSEMBLY)
a.

Disconnect the 3A and 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q1-3 (B) - Q1-2 (CTY) No. 1 room light switch in DOOR position Below 1 Ω
No. 1 room light switch in ON or OFF position 10 kΩ or higher
Q1-2 (CTY) - Body ground No. 1 room light switch in DOOR position 10 kΩ or higher



c.

Connect the 3A and 3B instrument panel junction block assembly connector.



OK

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAP LIGHT ASSEMBLY)

NG

REPLACE ROOF WIRE (INCLUDING NO. 1 ROOM LIGHT ASSEMBLY COMPONENTS THAT ARE PART OF THE WIRE HARNESS)

4.CHECK HARNESS AND CONNECTOR (DOME CUT RELAY - MAP LIGHT ASSEMBLY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q1-3 (B) - Body ground DOME CUT relay on 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3B instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q1-2 (CTY) - 3B-6 Always Below 1 Ω
Q1-2 (CTY) - Body ground Always 10 kΩ or higher




OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

U114311E01
0.157,0.099 0.313,0.245 0.156,0.145 10 *a 1.21,0.36 1.406,0.505 0.195,0.145 10 3B 4.69,0.36 4.938,0.526 0.248,0.166 10 MB 3.138,1.4 3.369,1.545 0.231,0.145 10 ILE 3.013,1.113 3.013,1.472 3.013,1.472 3.113,1.472 false

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3B-6 - MB-1 (ILE) Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY