The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU which uses this information to create the vehicle speed sensor signal*a. The vehicle speed sensor signal consists of pulses sent to the combination meter assembly from the skid control ECU. To create this signal, 12 V is output from IG2 which is behind a resistor in the combination meter assembly. This voltage is sent to the skid control ECU. The pulse signal is created by switching the transistor in the skid control ECU on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V or 5 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU. When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on the pulse signal.
*a: This vehicle speed sensor signal is created by the skid control ECU. There is no actual component that is referred to as the vehicle speed sensor. In addition, for some other systems, vehicle speed information may be exchanged using CAN communication.
This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication.
Disconnect the G1 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-39 (+S) - Body ground | Power switch on (IG) | 4.5 to 14 V |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
If any of the ECUs specified in the wiring diagram supplies power to the combination meter assembly, the combination meter assembly will output a waveform.
OK
NG
Reconnect the G1 combination meter assembly connector.
Disconnect the A41 skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-11 (SP1) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to Skid Control ECU) |
OK
NG
Check the input waveform.
Reconnect the A41 skid control ECU connector.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal G1-40 (SI) and body ground.
Turn the power switch on (IG).
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tool setting | 5 V/DIV., 20 ms/DIV. |
| Vehicle condition | Wheel being rotated |
| *a | Component with harness connected
(Combination Meter Assembly) |
The waveform is similar to that shown in the illustration.
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the G1 combination meter assembly and A41 skid control ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A41-11 (SP1) - G1-40 (SI) | Always | Below 1 Ω |
| A41-11 (SP1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the 3B junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-39 (+S) - 3B-15 | Always | Below 1 Ω |
| G1-39 (+S) - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect for a short in the circuit that is connected to the junction block connector shown in the wiring diagram.
If voltage is not present, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.
Disconnect the 3A, 3C junction connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-37 - Body ground | Power switch on (IG) | 4.5 to 14 V |
| 3A-16 - Body ground | Power switch on (IG) | 4.5 to 14 V |
| 3C-40 - Body ground | Power switch on (IG) | 4.5 to 14 V |
| Result | Proceed to |
|---|---|
| Voltage is not present in one circuit. | A |
| Voltage is present in all the circuits. | B |
A
B
Select the circuit for which voltage was not present in step 6.
| Tester Connection | System that uses the circuit | Proceed to |
|---|---|---|
| 3A-37 - Body ground | Hybrid control system | A |
| 3A-16 - Body ground | Audio/Visual system | B |
| 3C-40 - Body ground | Lighting system | C |
A
B
C
Disconnect the G57 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G57-14 (SPDI) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the G41 radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G41-17 (SPD) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the A34 headlight leveling ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-16 (SPDR) - Body ground | Always | 10 kΩ or higher |
OK
NG