The meter ECU receives the vehicle speed signal from the skid control ECU via the CAN communication system. The speed sensors detect the wheel speed and send signals to the skid control ECU. The skid control ECU supplies power to the vehicle speed sensors. The skid control ECU creates the vehicle speed signal based on the pulses of the voltage.
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a intelligent tester. For details about testing and the margin of error, see the reference chart (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
If the vehicle speed sensor circuit has a malfunction, the skid control ECU stores the DTCs. Troubleshoot the brake control system (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).
Before starting the following inspection, check tire size and tire air pressure.
Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
(See pagePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Combination Meter / Active Test.
Check the operation by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Speed Meter Operation | Speedometer | 0, 40, 80, 120, 160, 200, 240 km/h | - |
Speedometer indication is normal.
OK
NG
Check if brake control system DTCs are output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| DTCs are output. | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus:
for ABS/VSC/TRC: Chassis / ABS/VSC/TRC / Data List.
for Combination Meter: Body / Combination Meter / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed Meter | Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Result | Proceed to |
|---|---|
| The data list values of the ECUs match. | A |
| The data list values of the ECUs do not match. | B |
When the Data List values of the ECUs match, an internal malfunction of the combination meter assembly is suspected.
When the Data List values of the ECUs do not match, a signal output error of the skid control ECU or an internal malfunction of the combination meter assembly is suspected.
A
B
Replace the combination meter assembly with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).
| Result | Proceed to |
|---|---|
| The operation of the speedometer returns to normal. | A |
| The operation of the speedometer does not returns to normal (for LHD). | B |
| The operation of the speedometer does not returns to normal (for RHD). | C |
A
B
C