Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2013.12–2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1441/41  Air Mix Damper Control Servo Motor Circuit (Passenger Side)  


DESCRIPTION

The No. 1 air conditioning radiator damper servo sub-assembly (air mix) sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the No. 1 air conditioning radiator damper servo sub-assembly (air mix) to the appropriate position. This adjusts the amount of air passing through the heater core after passing the evaporator and controls the temperature of the output air.

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

HINT:

Confirm that no mechanical problem is present because this diagnostic code can be stored when either a damper link or the damper is mechanically locked.


DTC No. DTC Detection Condition Trouble Area
B1441/41 Air mix damper position sensor value does not change even though air conditioning amplifier assembly operates No. 1 air conditioning radiator damper servo sub-assembly (air mix).
·

No. 1 air conditioning radiator damper servo sub-assembly (air mix)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E229253E48
5.728,2.187 5.825,2.362 0.097,0.174 10 3 5.728,1.235 5.825,1.409 0.097,0.174 10 4 5.948,2.281 6.404,2.456 0.456,0.174 10 BUS 5.948,3.237 6.404,3.412 0.456,0.174 10 BUS G 5.54,4.085 5.782,4.259 0.242,0.174 10 z1 5.54,4.243 7.143,4.575 1.604,0.332 10 Air Conditioning Amplifier Assembly 0.05,4.099 2.936,4.414 2.886,0.316 10 No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Air Mix) 5.728,3.141 5.825,3.315 0.097,0.174 10 2 5.948,1.329 6.390,1.503 0.443,0.174 10 B BUS 3.416,4.085 4.971,4.440 1.555,0.355 10 Air Conditioning Harness Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Operate the temperature adjustment switch.


e.

Enter the following menus: Body / Air Conditioner / Data List.


f.

Check the value(s) by referring to the table below.


Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Mix Servo Actual Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (air mix) actual pulse / Min.: 128, Max.: 383 MAX. COLD: 257 (pulse)
MAX. HOT: 173 (pulse)
-

OK:

The display is as specified in the normal condition column.


Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Air Conditioner / Active Test.


e.

Check the operation by referring to the table below.


Air Conditioner
Tester Display Test Part Control Range Diagnostic Note
Air Mix Servo Targ Pulse(D) No. 1 air conditioning radiator damper servo sub-assembly (air mix) Min.: 128, Max.: 383 Operates between 173 and 257 pulses

OK:

Air temperature changes in accordance with each control range.



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

3.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX)
3.REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX)
a.

Replace the No. 1 air conditioning radiator damper servo sub-assembly (air mix) (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1441/41 is output A
DTC B1441/41 is not output B




A

4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY

B

END (NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (AIR MIX) WAS DEFECTIVE)

4.REPLACE AIR CONDITIONING HARNESS ASSEMBLY
a.

Replace the air conditioning harness assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT>REMOVAL).

HINT:

Since the air conditioning harness assembly cannot be inspected while it is removed from the vehicle, replace the air conditioning harness assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1441/41 is output A
DTC B1441/41 is not output B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

END (AIR CONDITIONING HARNESS ASSEMBLY WAS DEFECTIVE)