Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1471/71  A/C Inverter High Voltage Power Resource System Malfunction  


DESCRIPTION

The A/C inverter assembly monitors the voltage of the HV battery. It stops compressor control and stores the DTC when the monitored voltage is outside the specified range.

The DTC will be stored as a history DTC. Compressor control may not resume unless the power switch is turned off.

DTC No. DTC Detection Condition Trouble Area
B1471/71
·

Open or short in A/C inverter high voltage power resource system

·

The boost inverter is broken or malfunctioning


·

Electric vehicle fuse

·

No. 2 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly)

·

Compressor with motor assembly

·

Hybrid control system

·

CAN communication system



WIRING DIAGRAM

E235673E22
0.284,6.284 1.403,6.587 1.119,0.303 10 Compressor with Motor Assembly 5.785,3.954 7.111,4.296 1.325,0.342 10 Power Management Control ECU 6.052,1.845 6.340,1.994 0.288,0.149 10 STB 6.052,2.852 6.340,3.001 0.288,0.149 10 ITE 6.052,3.374 6.340,3.523 0.288,0.149 10 CLK 6.052,2.349 6.291,2.498 0.239,0.149 10 ETI 0.858,1.833 1.190,1.982 0.332,0.149 10 STBI 0.931,2.85 1.191,2.998 0.260,0.149 10 DIN 0.903,3.346 1.191,3.495 0.288,0.149 10 CLK 0.949,3.917 1.191,4.066 0.242,0.149 10 IG1 0.861,4.484 1.190,4.633 0.330,0.149 10 GND 0.981,5.277 1.191,5.426 0.210,0.149 10 PE 0.984,5.783 1.191,5.932 0.207,0.149 10 PB 0.77,2.337 1.189,2.486 0.420,0.149 10 DOUT 1.337,1.834 1.613,1.976 0.276,0.142 10 C22 1.337,2.345 1.613,2.487 0.276,0.142 10 C22 1.337,2.848 1.613,2.990 0.276,0.142 10 C22 1.337,3.363 1.613,3.505 0.276,0.142 10 C22 1.337,4.477 1.613,4.646 0.276,0.169 10 C22 1.337,3.918 1.613,4.060 0.276,0.142 10 C22 5.786,1.739 5.970,1.888 0.184,0.149 10 20 5.793,2.242 5.970,2.391 0.177,0.149 10 30 5.796,2.761 5.970,2.910 0.174,0.149 10 31 5.794,3.268 5.970,3.417 0.176,0.149 10 19 4.932,7.111 7.014,7.253 2.082,0.142 10 Inverter with Converter Assembly 5.23,5.694 5.331,5.856 0.100,0.162 10 1 5.23,5.176 5.331,5.345 0.100,0.170 10 2 1.36,5.266 1.632,5.408 0.271,0.142 10 D1 1.353,5.782 1.614,5.924 0.261,0.142 10 D1 1.431,5.082 1.532,5.231 0.100,0.149 10 1 1.422,5.594 1.523,5.764 0.100,0.170 10 2 1.418,1.663 1.518,1.812 0.100,0.149 10 4 1.418,2.15 1.518,2.320 0.100,0.170 10 3 1.421,2.671 1.521,2.820 0.100,0.149 10 2 1.418,3.167 1.518,3.336 0.100,0.170 10 1 1.418,3.739 1.518,3.888 0.100,0.149 10 6 1.426,4.29 1.527,4.460 0.100,0.170 10 5 5.407,5.161 5.813,5.310 0.406,0.149 10 ACPE 5.407,5.669 5.813,5.818 0.406,0.149 10 ACPB 5.716,5.942 6.192,6.425 0.475,0.482 10 Electric Vehicle Fuse 2.577,4.045 3.078,4.194 0.501,0.149 10 HTR-IG 4.168,3.911 5.569,4.060 1.401,0.149 10 from IG1 NO. 1 Relay 2.265,7.134 3.986,7.283 1.721,0.149 10 : CAN Communication Line 4.932,6.952 5.180,7.159 0.248,0.207 10 D2 5.785,3.812 6.080,3.996 0.295,0.184 10 A38 0.369,1.061 2.645,1.254 2.276,0.193 10 Air Conditioning Amplifier Assembly 2.732,6.315 3.941,6.545 1.209,0.230 10 No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.CHECK DIAGNOSTIC TROUBLE CODE (HYBRID CONTROL SYSTEM)

B

2.CHECK DIAGNOSTIC TROUBLE CODE (HYBRID CONTROL SYSTEM)
a.

Check if DTCs for the hybrid control system are output using the intelligent tester.

OK:

Hybrid control system DTCs are not output.




OK

3.INSPECT ELECTRIC VEHICLE FUSE

NG

3.INSPECT ELECTRIC VEHICLE FUSE
CAUTION:

Be sure to wear insulated gloves.


a.

Turn the power switch off.


b.

Remove the service plug grip (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL).

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch to on (READY) may cause a malfunction. Do not turn the power switch to on (READY) with the service plug grip removed.



c.

Remove the connector cover assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL).

NOTICE:

Be sure to prevent foreign objects or water from entering the inverter with converter assembly.



d.
E238086E03
1.448,1.052 2.406,1.052 false 1.417,1.771 2.406,1.771 false 1.302,0.958 1.427,1.156 0.125,0.198 10 false A 1.302,1.688 1.427,1.885 0.125,0.198 10 false B 0.5,0.729 0.802,1.031 0.302,0.302 10 false *a

Check that bolts A and B are tightened securely.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Item
(Tester Connection)
Condition Specified Condition
Electric vehicle fuse
(A - B)
Always Below 1 Ω


Text in Illustration
*a Electric Vehicle Fuse



OK

4.INSPECT NO. 2 ENGINE WIRE

NG

4.INSPECT NO. 2 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Disconnect the No. 2 engine wire connector (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-1 (PE) - D2-2 (ACPE) Always Below 1 Ω
D1-2 (PB) - D2-1 (ACPB) Always Below 1 Ω
D1-1 (PE) - Body ground Always 10 kΩ or higher
D1-2 (PB) - Body ground Always 10 kΩ or higher




OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG