Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1473/73  A/C Inverter Start-up Signal System Malfunction  


DESCRIPTION

The inverter activation signal is sent to the compressor with motor assembly from the power management control ECU. Compressor control is stopped and the DTC is stored if there is an open or short in the signal circuit.

DTC No. DTC Detection Condition Trouble Area
B1473/73 Open or short in A/C inverter start-up signal system
·

Harness or connector between power management control ECU and compressor with motor assembly

·

Compressor with motor assembly

·

Power management control ECU

·

Hybrid control system

·

CAN communication system



WIRING DIAGRAM

E235673E22
0.284,6.284 1.403,6.587 1.119,0.303 10 Compressor with Motor Assembly 5.785,3.954 7.111,4.296 1.325,0.342 10 Power Management Control ECU 6.052,1.845 6.340,1.994 0.288,0.149 10 STB 6.052,2.852 6.340,3.001 0.288,0.149 10 ITE 6.052,3.374 6.340,3.523 0.288,0.149 10 CLK 6.052,2.349 6.291,2.498 0.239,0.149 10 ETI 0.858,1.833 1.190,1.982 0.332,0.149 10 STBI 0.931,2.85 1.191,2.998 0.260,0.149 10 DIN 0.903,3.346 1.191,3.495 0.288,0.149 10 CLK 0.949,3.917 1.191,4.066 0.242,0.149 10 IG1 0.861,4.484 1.190,4.633 0.330,0.149 10 GND 0.981,5.277 1.191,5.426 0.210,0.149 10 PE 0.984,5.783 1.191,5.932 0.207,0.149 10 PB 0.77,2.337 1.189,2.486 0.420,0.149 10 DOUT 1.337,1.834 1.613,1.976 0.276,0.142 10 C22 1.337,2.345 1.613,2.487 0.276,0.142 10 C22 1.337,2.848 1.613,2.990 0.276,0.142 10 C22 1.337,3.363 1.613,3.505 0.276,0.142 10 C22 1.337,4.477 1.613,4.646 0.276,0.169 10 C22 1.337,3.918 1.613,4.060 0.276,0.142 10 C22 5.786,1.739 5.970,1.888 0.184,0.149 10 20 5.793,2.242 5.970,2.391 0.177,0.149 10 30 5.796,2.761 5.970,2.910 0.174,0.149 10 31 5.794,3.268 5.970,3.417 0.176,0.149 10 19 4.932,7.111 7.014,7.253 2.082,0.142 10 Inverter with Converter Assembly 5.23,5.694 5.331,5.856 0.100,0.162 10 1 5.23,5.176 5.331,5.345 0.100,0.170 10 2 1.36,5.266 1.632,5.408 0.271,0.142 10 D1 1.353,5.782 1.614,5.924 0.261,0.142 10 D1 1.431,5.082 1.532,5.231 0.100,0.149 10 1 1.422,5.594 1.523,5.764 0.100,0.170 10 2 1.418,1.663 1.518,1.812 0.100,0.149 10 4 1.418,2.15 1.518,2.320 0.100,0.170 10 3 1.421,2.671 1.521,2.820 0.100,0.149 10 2 1.418,3.167 1.518,3.336 0.100,0.170 10 1 1.418,3.739 1.518,3.888 0.100,0.149 10 6 1.426,4.29 1.527,4.460 0.100,0.170 10 5 5.407,5.161 5.813,5.310 0.406,0.149 10 ACPE 5.407,5.669 5.813,5.818 0.406,0.149 10 ACPB 5.716,5.942 6.192,6.425 0.475,0.482 10 Electric Vehicle Fuse 2.577,4.045 3.078,4.194 0.501,0.149 10 HTR-IG 4.168,3.911 5.569,4.060 1.401,0.149 10 from IG1 NO. 1 Relay 2.265,7.134 3.986,7.283 1.721,0.149 10 : CAN Communication Line 4.932,6.952 5.180,7.159 0.248,0.207 10 D2 5.785,3.812 6.080,3.996 0.295,0.184 10 A38 0.369,1.061 2.645,1.254 2.276,0.193 10 Air Conditioning Amplifier Assembly 2.732,6.315 3.941,6.545 1.209,0.230 10 No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.CHECK DIAGNOSTIC TROUBLE CODE

B

2.CHECK DIAGNOSTIC TROUBLE CODE
a.

Check if DTCs for the air conditioning system and the hybrid control system are output using the intelligent tester.

Result:
Result Proceed to
Only DTC B1473 is output A
DTCs B1473 and P3108 are output simultaneously (B1498 is not output)
DTCs B1473 and B1498 are output simultaneously (P3108 is not output) B
DTCs B1473, B1498 and P3108 are output simultaneously
DTCs other than P3108 are output for hybrid control system C




A

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR)

B

C

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.

Disconnect the A38 power management control ECU connector.


b.

Disconnect the C22 compressor with motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-20 (STB) - C22-4 (STBI) Always Below 1 Ω
A38-20 (STB) - Body ground Always 10 kΩ or higher




OK

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
a.

Reconnect the C22 compressor with motor assembly connector.


b.
U182013E02
0.147,0.106 0.334,0.269 0.187,0.163 10 *a 1.624,0.769 1.922,0.970 0.298,0.201 10 A38 1.071,3.018 1.379,3.172 0.309,0.154 10 STB 1.462,2.438 1.248,2.984 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-20 (STB) - Body ground Power switch on (IG) 11 to 14 V
A38-20 (STB) - Body ground Power switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY