Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1498/98  Communication Malfunction (A/C Inverter Local)  


DESCRIPTION

The power management control ECU and compressor with motor assembly transmit information to one another via a communication line. Compressor control is stopped and the DTC is stored if communication information is cut off or abnormal information occurs.

The DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.

The DTC will be stored as a history DTC.

DTC No. DTC Detection Condition Trouble Area
B1498/98
·

Communication line error or open between the power management control ECU and compressor with motor assembly.


·

High-voltage power source is shut off.


·

Harness or connector between power management control ECU, compressor with motor assembly and body ground

·

Power management control ECU

·

Compressor with motor assembly

·

No. 2 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly)

·

Electric vehicle fuse

·

CAN communication system

·

Hybrid control system



WIRING DIAGRAM

E235673E22
0.284,6.284 1.403,6.587 1.119,0.303 10 Compressor with Motor Assembly 5.785,3.954 7.111,4.296 1.325,0.342 10 Power Management Control ECU 6.052,1.845 6.340,1.994 0.288,0.149 10 STB 6.052,2.852 6.340,3.001 0.288,0.149 10 ITE 6.052,3.374 6.340,3.523 0.288,0.149 10 CLK 6.052,2.349 6.291,2.498 0.239,0.149 10 ETI 0.858,1.833 1.190,1.982 0.332,0.149 10 STBI 0.931,2.85 1.191,2.998 0.260,0.149 10 DIN 0.903,3.346 1.191,3.495 0.288,0.149 10 CLK 0.949,3.917 1.191,4.066 0.242,0.149 10 IG1 0.861,4.484 1.190,4.633 0.330,0.149 10 GND 0.981,5.277 1.191,5.426 0.210,0.149 10 PE 0.984,5.783 1.191,5.932 0.207,0.149 10 PB 0.77,2.337 1.189,2.486 0.420,0.149 10 DOUT 1.337,1.834 1.613,1.976 0.276,0.142 10 C22 1.337,2.345 1.613,2.487 0.276,0.142 10 C22 1.337,2.848 1.613,2.990 0.276,0.142 10 C22 1.337,3.363 1.613,3.505 0.276,0.142 10 C22 1.337,4.477 1.613,4.646 0.276,0.169 10 C22 1.337,3.918 1.613,4.060 0.276,0.142 10 C22 5.786,1.739 5.970,1.888 0.184,0.149 10 20 5.793,2.242 5.970,2.391 0.177,0.149 10 30 5.796,2.761 5.970,2.910 0.174,0.149 10 31 5.794,3.268 5.970,3.417 0.176,0.149 10 19 4.932,7.111 7.014,7.253 2.082,0.142 10 Inverter with Converter Assembly 5.23,5.694 5.331,5.856 0.100,0.162 10 1 5.23,5.176 5.331,5.345 0.100,0.170 10 2 1.36,5.266 1.632,5.408 0.271,0.142 10 D1 1.353,5.782 1.614,5.924 0.261,0.142 10 D1 1.431,5.082 1.532,5.231 0.100,0.149 10 1 1.422,5.594 1.523,5.764 0.100,0.170 10 2 1.418,1.663 1.518,1.812 0.100,0.149 10 4 1.418,2.15 1.518,2.320 0.100,0.170 10 3 1.421,2.671 1.521,2.820 0.100,0.149 10 2 1.418,3.167 1.518,3.336 0.100,0.170 10 1 1.418,3.739 1.518,3.888 0.100,0.149 10 6 1.426,4.29 1.527,4.460 0.100,0.170 10 5 5.407,5.161 5.813,5.310 0.406,0.149 10 ACPE 5.407,5.669 5.813,5.818 0.406,0.149 10 ACPB 5.716,5.942 6.192,6.425 0.475,0.482 10 Electric Vehicle Fuse 2.577,4.045 3.078,4.194 0.501,0.149 10 HTR-IG 4.168,3.911 5.569,4.060 1.401,0.149 10 from IG1 NO. 1 Relay 2.265,7.134 3.986,7.283 1.721,0.149 10 : CAN Communication Line 4.932,6.952 5.180,7.159 0.248,0.207 10 D2 5.785,3.812 6.080,3.996 0.295,0.184 10 A38 0.369,1.061 2.645,1.254 2.276,0.193 10 Air Conditioning Amplifier Assembly 2.732,6.315 3.941,6.545 1.209,0.230 10 No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.

·

Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.CHECK DIAGNOSTIC TROUBLE CODE

B

2.CHECK DIAGNOSTIC TROUBLE CODE
a.

Check if DTCs for the hybrid control system are output using the intelligent tester.


Result:
Result Proceed to
DTC is not output A
Only DTC P3108 is output A
DTCs other than P3108 are output B



A

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)

B

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.

Disconnect the C22 compressor with motor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-5 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG POWER SOURCE, GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG POWER SOURCE, GROUND)
a.

Turn the power switch on (IG).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C22-6 (IG1) - C22-5 (GND) Power switch on (IG) 11 to 14 V
C22-6 (IG1) - C22-5 (GND) Power switch off Below 1 V




OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR)
a.

Disconnect the A38 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C22-1 (CLK) - A38-19 (CLK) Always Below 1 Ω
C22-2 (DIN) - A38-31 (ITE) Always Below 1 Ω
C22-3 (DOUT) - A38-30 (ETI) Always Below 1 Ω
C22-1 (CLK) - Body ground Always 10 kΩ or higher
C22-2 (DIN) - Body ground Always 10 kΩ or higher
C22-3 (DOUT) - Body ground Always 10 kΩ or higher




OK

6.INSPECT ELECTRIC VEHICLE FUSE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT ELECTRIC VEHICLE FUSE
CAUTION:

Be sure to wear insulated gloves.


a.

Turn the power switch off.


b.

Remove the service plug grip (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL).

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.



c.

Remove the connector cover assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL).

NOTICE:

Be sure to prevent foreign objects or water from entering the inverter with converter assembly.



d.
E238086E03
1.448,1.052 2.406,1.052 false 1.417,1.771 2.406,1.771 false 1.302,0.958 1.427,1.156 0.125,0.198 10 false A 1.302,1.688 1.427,1.885 0.125,0.198 10 false B 0.5,0.729 0.802,1.031 0.302,0.302 10 false *a

Check that bolts A and B are tightened securely.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Item
(Tester Connection)
Condition Specified Condition
Electric vehicle fuse
(A - B)
Always Below 1 Ω


Text in Illustration
*a Electric Vehicle Fuse



OK

7.INSPECT NO. 2 ENGINE WIRE

NG

7.INSPECT NO. 2 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Disconnect the No. 2 engine wire connector (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-1 (PE) - D2-1 (ACPE) Always Below 1 Ω
D1-2 (PB) - D2-2 (ACPB) Always Below 1 Ω
D1-1 (PE) - Body ground Always 10 kΩ or higher
D1-2 (PB) - Body ground Always 10 kΩ or higher




OK

8.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

8.REPLACE COMPRESSOR WITH MOTOR ASSEMBLY
a.

Replace the compressor with motor assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL).

HINT:

Since the compressor with motor assembly cannot be inspected while it is removed from the vehicle, replace the compressor with motor assembly with a new or known good one and check that the condition returns to normal.



b.

Check for the DTC.

Result:
Result Proceed to
DTC B1498/98 is not output A
DTC B1498/98 is output B




A

END (COMPRESSOR WITH MOTOR ASSEMBLY WAS DEFECTIVE)

B