Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2011.12–2014.12
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  P0AA6-611  Hybrid Battery Voltage System Isolation Fault  


DESCRIPTION

This DTC is stored if there is insulation trouble with the high-voltage circuit in the air conditioning system. Possible causes are poor insulation in the compressor with motor assembly, or mixing of any oil other than ND-OIL 11 in the refrigerant cycle.

A high-voltage motor is built into the electrical compressor and is cooled directly with refrigerant. Compressor oil (ND-OIL 11) with high insulation performance is used because a leakage of electrical power may occur if regular compressor oil (ND-OIL 8) is used.

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



DTC No. DTC Detection Condition Trouble Area
P0AA6-611 High voltage system insulation malfunction
·

Compressor oil

·

Refrigerant pipe line

·

Compressor with motor assembly

·

CAN communication system



WIRING DIAGRAM

E235673E22
0.284,6.284 1.403,6.587 1.119,0.303 10 Compressor with Motor Assembly 5.785,3.954 7.111,4.296 1.325,0.342 10 Power Management Control ECU 6.052,1.845 6.340,1.994 0.288,0.149 10 STB 6.052,2.852 6.340,3.001 0.288,0.149 10 ITE 6.052,3.374 6.340,3.523 0.288,0.149 10 CLK 6.052,2.349 6.291,2.498 0.239,0.149 10 ETI 0.858,1.833 1.190,1.982 0.332,0.149 10 STBI 0.931,2.85 1.191,2.998 0.260,0.149 10 DIN 0.903,3.346 1.191,3.495 0.288,0.149 10 CLK 0.949,3.917 1.191,4.066 0.242,0.149 10 IG1 0.861,4.484 1.190,4.633 0.330,0.149 10 GND 0.981,5.277 1.191,5.426 0.210,0.149 10 PE 0.984,5.783 1.191,5.932 0.207,0.149 10 PB 0.77,2.337 1.189,2.486 0.420,0.149 10 DOUT 1.337,1.834 1.613,1.976 0.276,0.142 10 C22 1.337,2.345 1.613,2.487 0.276,0.142 10 C22 1.337,2.848 1.613,2.990 0.276,0.142 10 C22 1.337,3.363 1.613,3.505 0.276,0.142 10 C22 1.337,4.477 1.613,4.646 0.276,0.169 10 C22 1.337,3.918 1.613,4.060 0.276,0.142 10 C22 5.786,1.739 5.970,1.888 0.184,0.149 10 20 5.793,2.242 5.970,2.391 0.177,0.149 10 30 5.796,2.761 5.970,2.910 0.174,0.149 10 31 5.794,3.268 5.970,3.417 0.176,0.149 10 19 4.932,7.111 7.014,7.253 2.082,0.142 10 Inverter with Converter Assembly 5.23,5.694 5.331,5.856 0.100,0.162 10 1 5.23,5.176 5.331,5.345 0.100,0.170 10 2 1.36,5.266 1.632,5.408 0.271,0.142 10 D1 1.353,5.782 1.614,5.924 0.261,0.142 10 D1 1.431,5.082 1.532,5.231 0.100,0.149 10 1 1.422,5.594 1.523,5.764 0.100,0.170 10 2 1.418,1.663 1.518,1.812 0.100,0.149 10 4 1.418,2.15 1.518,2.320 0.100,0.170 10 3 1.421,2.671 1.521,2.820 0.100,0.149 10 2 1.418,3.167 1.518,3.336 0.100,0.170 10 1 1.418,3.739 1.518,3.888 0.100,0.149 10 6 1.426,4.29 1.527,4.460 0.100,0.170 10 5 5.407,5.161 5.813,5.310 0.406,0.149 10 ACPE 5.407,5.669 5.813,5.818 0.406,0.149 10 ACPB 5.716,5.942 6.192,6.425 0.475,0.482 10 Electric Vehicle Fuse 2.577,4.045 3.078,4.194 0.501,0.149 10 HTR-IG 4.168,3.911 5.569,4.060 1.401,0.149 10 from IG1 NO. 1 Relay 2.265,7.134 3.986,7.283 1.721,0.149 10 : CAN Communication Line 4.932,6.952 5.180,7.159 0.248,0.207 10 D2 5.785,3.812 6.080,3.996 0.295,0.184 10 A38 0.369,1.061 2.645,1.254 2.276,0.193 10 Air Conditioning Amplifier Assembly 2.732,6.315 3.941,6.545 1.209,0.230 10 No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Electrical insulation performance may decrease significantly if even a small amount of oil other than ND-OIL 11 is used (or enters) in the refrigerant cycle, causing the DTC to be output.

·

If other oil is accidentally used and a DTC is output, collect as much oil in the refrigerant cycle into the compressor as possible and replace it with ND-OIL 11 to increase the ND-OIL 11 ratio amount.

·

Replace the main components (evaporator, condenser, and compressor) if a large amount of oil other than ND-OIL 11 enters the system. Failing to do so may cause electrical insulation performance to remain low, causing the DTC to be output.

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.



HINT:

If it can be confirmed that any compressor oil other than ND-OIL 11 has been used in the vehicle, replace the main components of the air conditioning cycle.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY

B

2.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Because the compressor has a high-voltage circuit, wear insulated gloves and pull out the service plug grip to cut off the high-voltage circuit before inspection.



b.

Turn the power switch on (READY).


c.

Prepare the vehicle according to the table below for 3 minutes.

Item Condition
Blower speed HI
Temperature setting MAX COLD
A/C On


d.

Turn the power switch off.


e.

Remove the service plug grip (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL).

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.



f.
U159684E01
1.663,0.597 1.935,0.752 0.272,0.156 10 D1 0.352,0.365 0.624,0.520 0.272,0.156 10 *a 0.838,1.8 1.110,1.955 0.272,0.156 10 PB 2.402,1.8 2.674,1.955 0.272,0.156 10 PE 1.559,1.471 1.057,1.766 false 1.968,1.471 2.469,1.766 false

Disconnect the D1 compressor with motor assembly connector.


g.

Using a megohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-1 (PE) - Body ground Always 2 MΩ or higher
D1-2 (PB) - Body ground Always 2 MΩ or higher


Text in Illustration
*a Component without harness connected
(Compressor with Motor Assembly)



OK

3.INSPECT AIR CONDITIONING CYCLE

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

3.INSPECT AIR CONDITIONING CYCLE
CAUTION:

Because the compressor has a high-voltage circuit, wear insulated gloves and pull out the service plug grip to cut off the high-voltage circuit before inspection.


a.

Reconnect the D1 compressor with motor assembly connector.



c.

Turn the power switch on (READY).


d.

Set the A/C temperature to 25°C (77°F) and the blower switch to LO and then operate the compressor for 10 minutes to circulate the refrigerant and collect as much compressor oil as possible in the compressor.


e.

Turn the power switch off.


f.

Using a spot cooler or other tools, cool down the compressor with motor assembly for 30 minutes, or leave the vehicle overnight before inspection.

NOTICE:

Do not operate the compressor before inspection.



g.

Remove the service plug grip (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>SERVICE PLUG GRIP>REMOVAL).

CAUTION:

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.


NOTICE:

After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.



h.
U159684E01
1.663,0.597 1.935,0.752 0.272,0.156 10 D1 0.352,0.365 0.624,0.520 0.272,0.156 10 *a 0.838,1.8 1.110,1.955 0.272,0.156 10 PB 2.402,1.8 2.674,1.955 0.272,0.156 10 PE 1.559,1.471 1.057,1.766 false 1.968,1.471 2.469,1.766 false

Disconnect the D1 compressor with motor assembly connector.


i.

Using a megohmmeter, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D1-1 (PE) - Body ground Always 3 MΩ or higher
D1-2 (PB) - Body ground Always 3 MΩ or higher


NOTICE:

If the results are out of the specified range, replace the compressor without operating it.


Text in Illustration
*a Component without harness connected
(Compressor with Motor Assembly)



OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG