This DTC is stored if the amount of refrigerant in the air conditioning system is insufficient.
The air conditioning amplifier assembly receives the ambient temperature signal, refrigerant pressure signal etc. from various sensors.
Based on these signals, the air conditioning amplifier assembly detects the amount of refrigerant.
The A/C switch indicator is turned off and air conditioning system is stopped if the amount of refrigerant is insufficient.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B14B8 | When the following conditions is detected using the refrigerant shortage check in normal operation:
The amount of refrigerant is insufficient. |
·
Refrigerant pipe line ·
Cooler expansion valve ·
Air conditioning amplifier assembly |
If DTC B1423 and B14B8 are output at the same time, troubleshoot for DTC B1423 first.
Install a manifold gauge set.
Recover the refrigerant from the air conditioning system using a refrigerant recovery unit.
Evacuate the air conditioning system and check that vacuum can be maintained in it.
Vacuum can be maintained in the air conditioning system.
If vacuum cannot be maintained in the air conditioning system, refrigerant may be leaking from it. In this case, it is necessary to repair or replace the leaking part of the air conditioning system.
OK
NG
Add an appropriate amount of refrigerant (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT).
NEXT
Turn the power switch on (READY).
Check for DTCs when the following conditions are met (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR).
| Item | Condition |
|---|---|
| A/C Switch | On |
| Blower Switch | On |
| A/C operation time | 15 minutes or more |
| Ambient temperature* | 0 to 49°C (32 to 120°F) |
| Engine coolant temperature | 45°C (113°F) or more |
*: If the ambient temperature is not within the range shown, do not perform this check.
| Result | Proceed to |
|---|---|
| DTC B14B8 is output | A |
| DTC B14B8 is not output | B |
A
B
Replace the cooler expansion valve with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>COOLER EXPANSION VALVE>REMOVAL).
Replace the cooler expansion valve with a new or known good one because the cooler expansion valve is either stuck or clogged.
NEXT
Add an appropriate amount of refrigerant (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT).
NEXT
Turn the power switch on (READY).
Check for DTCs when the following conditions are met (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR).
| Item | Condition |
|---|---|
| A/C Switch | On |
| Blower Switch | On |
| A/C operation time | 15 minutes or more |
| Ambient temperature* | 0 to 49°C (32 to 120°F) |
| Engine coolant temperature | 45°C (113°F) or more |
*: If the ambient temperature is not within the range shown, do not perform this check.
| Result | Proceed to |
|---|---|
| DTC B14B8 is output | A |
| DTC B14B8 is not output | B |
A
B
Identify the area where refrigerant leaks (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT).
Repair the identified area of the air conditioning system.
Evacuate the air conditioning system.
NEXT
Add an appropriate amount of refrigerant (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT).
NEXT
Turn the power switch on (READY).
Check for DTCs when the following conditions are met (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR).
| Item | Condition |
|---|---|
| A/C Switch | On |
| Blower Switch | On |
| A/C operation time | 15 minutes or more |
| Ambient temperature* | 0 to 49°C (32 to 120°F) |
| Engine coolant temperature | 45°C (113°F) or more |
*: If the ambient temperature is not within the range shown, do not perform this check.
| Result | Proceed to |
|---|---|
| DTC B14B8 is output | A |
| DTC B14B8 is not output | B |
A
B
Replace the cooler expansion valve with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>COOLER EXPANSION VALVE>REMOVAL).
Replace the cooler expansion valve with a new or known good one because the cooler expansion valve is either stuck or clogged.
NEXT
Add an appropriate amount of refrigerant (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT>REPLACEMENT).
NEXT
Turn the power switch on (READY).
Check for DTCs when the following conditions are met (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR).
| Item | Condition |
|---|---|
| A/C Switch | On |
| Blower Switch | On |
| A/C operation time | 15 minutes or more |
| Ambient temperature* | 0 to 49°C (32 to 120°F) |
| Engine coolant temperature | 45°C (113°F) or more |
*: If the ambient temperature is not within the range shown, do not perform this check.
| Result | Proceed to |
|---|---|
| DTC B14B8 is output | A |
| DTC B14B8 is not output | B |
A
B