Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2013.12–2014.12
RM2170E _58 Vehicle Interior _057044 INTERIOR PANELS / TRIM _0278146 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


PROCEDURE

Hide 1.INSTALL ROOF HEADLINING ASSEMBLY

a.
B301725

Pull the roof headlining back into the vehicle through the back door.

NOTICE:

Do not damage the roof headlining assembly or body interior.



b.

Engage the claw.


c.

Install the roof headlining assembly with the 3 clips.


d.

for front pillar RH side:

i.

Engage the 3 clamps.


ii.

Connect the connector.



e.

for front pillar LH side:

i.

Engage the 3 clamps.


ii.

Connect the connector.



f.

for rear pillar RH side:

i.

Engage the 2 clamps.


ii.

Connect the connector bracket with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


iii.

Connect the connector.



Hide 74348 2.INSTALL VISOR HOLDER

a.
B211698

Engage the 2 claws and turn the visor holder counterclockwise 45° to install it.

HINT:

Use the same procedure for the RH side and LH side.



Hide 74320 3.INSTALL VISOR ASSEMBLY LH

a.
B322943

Install the visor assembly LH with the 2 screws.

HINT:

Install the visor assembly LH with the arrow facing the front of the vehicle.



b.

Connect the visor shaft into the visor holder.


Hide 74310 4.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74610S 5.INSTALL ASSIST GRIP ASSEMBLY

HINT:

Use the same procedure to install all assist grips.


a.
B203057

Assemble the front assist grip assembly as shown in the illustration.


b.
B229265

Install the assist grip assembly.


Hide 62472A 7.INSTALL ROOF SIDE INNER GARNISH LH

a.

Pass the floor anchor of the rear seat 3 point type outer belt assembly LH through the roof side inner garnish LH.


b.

Engage the 5 clips to install the roof side inner garnish LH.


Hide 64740C 8.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Engage the guide, 4 claws and 4 clips.

B300800E02
2.104,3.948 2.344,4.021 false 1.958,3.885 2.146,4.052 0.188,0.167 10 true *1

Text in Illustration
*1 Rear Seatback Hinge - -


b.

Install the deck trim side panel assembly LH with the bolt and 2 screws.


c.

Turn the rear seatback hinge in the direction indicated by the arrow shown in the illustration.


Hide 58732C 9.INSTALL REAR ABSORBER CAP LH

a.

Engage the 2 guides and 2 claws to install the rear absorber cap LH.


Hide 81330 10.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 73370 11.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

Hide 62471A 12.INSTALL ROOF SIDE INNER GARNISH RH

a.

Pass the floor anchor of the rear seat 3 point type outer belt assembly RH through the roof side inner garnish RH.


b.

Engage the 5 clips to install the roof side inner garnish RH.


c.
B297734

Engage the guide and 4 claws to connect the belt guide.


Hide 73350 13.CONNECT REAR CENTER SEAT LAP TYPE BELT ASSEMBLY

Hide 64730B 14.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 58731C 15.INSTALL REAR ABSORBER CAP RH

HINT:

Use the same procedure as for the LH side.


Hide 73360 16.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64716D 17.INSTALL REAR DECK TRIM COVER

a.

Engage the 2 guides and 4 claws.


b.

Install the rear deck trim cover with the 2 clips.


Hide 64330D 18.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

a.

Install the package tray trim panel assembly.


Hide 64997 19.INSTALL DECK FLOOR BOX LH

a.

Install the deck floor box LH.


Hide 64995 20.INSTALL DECK FLOOR BOX RH

HINT:

Use the same procedure as for the LH side.


Hide 58410B 21.INSTALL DECK BOARD ASSEMBLY

a.

Install the deck board assembly.


Hide 62412B 22.INSTALL CENTER PILLAR UPPER GARNISH LH

a.

Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.


b.

Engage the clip.


c.

Install the center pillar upper garnish LH with the 2 screws.


Hide 62414A 23.INSTALL CENTER PILLAR LOWER GARNISH LH

a.

Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.


Hide 73220 24.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 73233C 25.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 62332A 26.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B299875E02
2.521,1.104 2.469,0.823 false 1.375,0.656 1.083,0.75 false 2.448,1.115 2.604,1.26 0.156,0.146 10 false *b 1.375,0.573 1.531,0.719 0.156,0.146 10 false *a

Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

Text in Illustration
*a Alignment Mark (White)
*b Flange Position

NOTICE:

After installation, check that the corners fit correctly.



Hide 62212 27.INSTALL FRONT PILLAR GARNISH LH

a.

Remove the protective cover.


b.

Make sure that the front pillar garnish clip is not damaged.

NOTICE:

If there is any damage, replace the garnish clip with a new one.



c.
E276148E03
0.958,0.781 0.958,1.052 false 2.438,2.573 2.688,2.792 0.25,0.219 10 true (1) 0.906,0.104 1.135,0.313 0.229,0.208 10 false (2) 0.24,0.677 0.469,0.885 0.229,0.208 10 false (4) 1.76,0.125 1.99,0.333 0.229,0.208 10 false (5) 0.896,1.063 1.125,1.271 0.229,0.208 10 false *a 1.417,0.135 1.646,0.313 0.229,0.177 10 false (3)

Push the front pillar garnish LH in the direction indicated by the arrow (1) shown in the illustration to engage the 2 guides.

Text in Illustration
*a Protective Tape


d.

Using needle-nose pliers with the tips wrapped with protective tape, bend the end of the front pillar garnish clip in the direction indicated by the arrow (2) shown in the illustration.


e.

Push the front pillar garnish LH in the direction indicated by the arrow (3) shown in the illustration and insert it to the front pillar garnish clip.


f.

Using needle-nose pliers with the tips wrapped with protective tape, rotate the front pillar garnish clip in the direction indicated by the arrow (4) shown in the illustration.

HINT:

Rotate the front pillar garnish clip so that the longer end of the front pillar garnish clip is positioned at the bottom.



g.

Using needle-nose pliers with the tips wrapped with protective tape, push the front pillar garnish clip in the direction indicated by the arrow (5) and rotate it to the position shown in the illustration.

HINT:

Make sure that the front pillar garnish clip is positioned as shown in the illustration. Failing to do so may cause a gap between the front pillar garnish LH and roof headlining assembly.



h.
E276149E03
1.26,0.375 1.052,0.646 false 0.917,0.656 1.104,0.854 0.188,0.198 10 false *1

Engage the clip and front pillar garnish clip to install the front pillar garnish LH.

Text in Illustration
*1 Front Pillar Garnish Clip

NOTICE:

If there is a gap between the front pillar garnish LH and roof headlining assembly, the front pillar garnish clip is not installed correctly. While lightly pressing the front pillar garnish LH as shown in the illustration, push it towards the front pillar garnish clip side.


HINT:

Make sure that the curtain shield airbag assembly LH is not pinched.



Hide 62312B 28.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B299871E02
2.521,1.135 2.469,0.844 false 1.375,0.688 1.083,0.771 false 2.479,1.167 2.688,1.365 0.208,0.198 10 false *b 1.427,0.583 1.677,0.76 0.25,0.177 10 false *a

Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

Text in Illustration
*a Alignment Mark (Yellow)
*b Flange Position

NOTICE:

After installation, check that the corners fit correctly.



Hide 62112 29.INSTALL COWL SIDE TRIM BOARD LH

a.

Engage the clip.


b.

Install the cowl side trim board with the clip.


Hide 67914 30.INSTALL FRONT DOOR SCUFF PLATE LH

a.

Engage the 8 claws to install the front door scuff plate.


Hide 67918A 31.INSTALL REAR DOOR SCUFF PLATE LH

a.

Engage the guide and the 5 claws to install the rear door scuff plate.


Hide 62411B 32.INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 33.INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73210 34.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 35.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 62331A 36.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.
B299873E02
2.521,1.104 2.469,0.823 false 1.365,0.656 1.073,0.75 false 2.479,1.146 2.719,1.323 0.24,0.177 10 false *b 1.396,0.542 1.729,0.792 0.333,0.25 10 false *a

Align the alignment mark (Red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

Text in Illustration
*a Alignment Mark (Red)
*b Flange Position

NOTICE:

After installation, check that the corners fit correctly.



Hide 62211 37.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 38.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 39.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B299869E02
2.521,1.208 2.469,0.917 false 1.375,0.76 1.083,0.844 false 2.448,1.208 2.604,1.354 0.156,0.146 10 false *b 1.375,0.677 1.531,0.823 0.156,0.146 10 false *a

Align the alignment mark (Yellow green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

Text in Illustration
*a Alignment Mark (Yellow green)
*b Flange Position

NOTICE:

After installation, check that the corners fit correctly.



Hide 62111C 40.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67913 41.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 71960B 45.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

Hide 71940A 46.INSTALL REAR SEAT HEADREST ASSEMBLY