Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Key-off Operation Function Operates even if Operating Conditions are not Satisfied  


DESCRIPTION

·

When the front doors are closed, each power window regulator motor assembly can control its power window operation for approximately 43 seconds after the power switch is turned from on (IG) to off by receiving operation permission signals from the main body ECU (multiplex network body ECU).

·

However, when approximately 43 seconds have elapsed, or the driver door or front passenger door is opened within approximately 43 seconds of the power switch being turned off, the power window regulator motor assembly stops operating.

·

During an auto operation, when 43 seconds have passed and key-off operation is prohibited, the window continues the operation until the auto operation is completed.


CAUTION / NOTICE / HINT

NOTICE:

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.


PROCEDURE

1.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the manual up and down functions using the power window regulator master switch assembly and power window regulator switch assembly can operate all the power windows (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Manual up and down functions are normal.




OK

2.CHECK REMOTE UP / DOWN FUNCTION

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

2.CHECK REMOTE UP / DOWN FUNCTION
a.

Check that the remote up and down functions using the power window regulator master switch assembly can operate all the power windows (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).

OK:

Remote up and down functions are normal.




OK

3.CHECK OPERATION FUNCTION AFTER POWER SWITCH IS TURNED OFF

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

3.CHECK OPERATION FUNCTION AFTER POWER SWITCH IS TURNED OFF
a.

Check the power window operation function after the power switch is turned off.

Result:
Result Proceed to
When power window can still be operated even after opening driver door or front passenger door within approximately 43 seconds of power switch being turned off A
When power window can still be operated even after approximately 43 seconds have elapsed after power switch is turned off (for All Doors) B
When power window can still be operated even after approximately 43 seconds have elapsed after power switch is turned off (for Driver Door) C
When power window can still be operated even after approximately 43 seconds have elapsed after power switch is turned off (Front Passenger Door, Rear LH Door or Rear RH Door) D




A

4.READ VALUE USING INTELLIGENT TESTER

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

D

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
4.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body (Main Body ECU (Multiplex Network Body ECU))
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch RH / OPEN or CLOSE CLOSE: Front door RH closed
OPEN: Front door RH open
-
FL Door Courtesy Front door courtesy light switch LH / OPEN or CLOSE CLOSE: Front door LH closed
OPEN: Front door LH open
-

OK:

On the intelligent tester screen, ON or OFF is displayed accordingly.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO LIGHTING SYSTEM (Proceed to Front Door Courtesy Switch Circuit)

5.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).



NEXT

6.CHECK POWER WINDOW CONTROL SYSTEM
6.CHECK POWER WINDOW CONTROL SYSTEM
a.

Check the power window operation function after the power switch is turned off.

OK:

The power window control system operates normally.




OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY