Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2014.12–2015.11
RM2170E _59 Vehicle Exterior _057046 DOOR / HATCH _0278160 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 67001A 4.INSTALL FRONT DOOR PANEL CUSHION

a.
B307112

Engage each claw to Install the 2 cushions onto the door panel.


Hide 69312 5.INSTALL FRONT DOOR LOCK OPEN ROD

a.
B307113E01
3.018,0.578 3.217,0.770 0.198,0.192 10 (1) 2.485,0.142 2.683,0.334 0.198,0.192 10 (2)

Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 69202A 6.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.


b.
B312743

Engage the guide and 2 clamps.


c.

Temporary install the front door outside handle frame sub-assembly to the front door.


d.
B307114E02
0.135,2.5 0.333,2.667 0.198,0.167 10 false *b 0.135,0.094 0.333,0.26 0.198,0.167 10 true *a

Engage the door handle nut and 2 claws.

Text in Illustration
*a Outside
*b Inside


e.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69760C 7.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY

a.
B307115

Install the front door inside locking cable assembly as shown in the illustration.


b.
B307116

Engage the 3 claws as shown in the illustration.


Hide 69720C 8.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B307117

Install the front door lock remote control cable assembly as shown in the illustration.


Hide 69320 9.INSTALL FRONT DOOR LOCK ASSEMBLY

NOTICE:
·

When reusing the removed front door lock assembly, replace the door lock wiring harness seal on the connector with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal surface of the connector.

·

Reusing the door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water intrusion. This may result in a malfunction of the front door lock assembly.



a.

Apply MP grease to the sliding parts of the front door lock assembly.


b.

When reusing the front door lock assembly:

i.
B307105

Install a new door lock wiring harness seal to the front door lock assembly.



c.
B307118E03
0.552,0.76 0.677,0.76 true 0.729,0.667 0.927,0.865 0.198,0.198 10 true *1

Insert the front door lock open rod to the front door lock assembly.

Text in Illustration
*1 Front Door Lock Open Rod

HINT:

Make sure that the front door lock open rod is securely connected to the front door lock assembly.



d.

Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.

Connect the connector.


Hide 69242E 10.INSTALL FRONT DOOR OUTSIDE HANDLE REAR PAD

a.
B307103

Engage the 2 claws to install the front door outside handle rear pad.


Hide 69241H 11.INSTALL FRONT DOOR OUTSIDE HANDLE FRONT PAD

a.
B307102

Engage the 3 claws to install the front door outside handle front pad.


Hide 69220 12.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY

a.
B307119

Insert the front end of the front door outside handle assembly into the front door outside handle frame.


b.

Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.


c.
B307120

Connect the connector.


d.

Engage the 3 claws.


Hide 69217F 13.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B308298

Engage the 2 guides and claw to install the front door outside handle cover to the front door lock cylinder.


Hide 69217E 14.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B300049

Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B297584

Install the hole plug.


Hide 15.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B307098

Install the front door outside handle cover with lock cylinder assembly.

HINT:

Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.



b.

Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B299844

Install the hole plug.


Hide 68215 16.INSTALL FRONT DOOR FIX WINDOW WEATHERSTRIP

a.

Install the front door fix window glass onto the front door fix window weatherstrip.


b.
B307121

Install the front door fix window weatherstrip with the front door fix window glass.


Hide 67402F 17.INSTALL FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

a.
B307096

Temporary install the front door front lower frame sub-assembly with the 2 bolts.


b.

Install the screw.


c.

Tighten the 2 bolts to install the front door front lower frame sub-assembly.


Hide 67404F 18.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

a.
B307095

Engage the guide.


b.

Install the front door rear lower frame sub-assembly with the bolt.


Hide 67862 19.INSTALL FRONT DOOR WEATHERSTRIP

a.
B307094

Engage the 30 clips to install the front door weatherstrip.


Hide 68610 20.INSTALL FRONT DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding areas of the front door check assembly.


b.
B307093E05
2.448,1.021 2.677,1.198 0.229,0.177 10 true (A) 1.323,0.563 1.552,0.74 0.229,0.177 10 true (B) 1.271,1.49 1.5,1.667 0.229,0.177 10 true (B)

Apply adhesive to the threads of the bolt (A).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the front door check assembly with the 3 bolts.

Torque:
Bolt (A) : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt (B) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68141C 21.INSTALL FRONT DOOR GLASS RUN

a.
B450304E02
2.427,1.927 2.552,2.104 0.125,0.177 10 true 2 1.563,1.344 1.688,1.521 0.125,0.177 10 false 1 2,1.594 2.125,1.771 0.125,0.177 10 false 3

Engage the 2 guides and install the front door glass run in the order shown in the illustration.

NOTICE:

Make sure that the 2 guides are securely engaged.



Hide 85720D 22.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY

NOTICE:

The regulator arm must be below the intermediate position when installing the power window regulator motor.


a.
B307091

Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

HINT:

A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.



Hide 23.INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY

a.

Apply MP grease to the sliding parts of the front door window regulator assembly.


b.

Install the temporary bolt to the front door window regulator assembly.


c.
B307122E02
2.156,0.844 1.979,0.844 false 2.021,1.625 2.219,1.802 0.198,0.177 10 true (1) 2.594,0.313 2.792,0.49 0.198,0.177 10 true (2) 2.792,1.385 2.99,1.563 0.198,0.177 10 true (3) 1.854,0.24 2.052,0.417 0.198,0.177 10 true (4) 0.865,0.646 1.063,0.823 0.198,0.177 10 true (5) 1.438,0.448 1.635,0.625 0.198,0.177 10 true (6) 1.813,0.771 1.979,0.917 0.167,0.146 10 true *1

Temporarily install the front door window regulator assembly.

Text in Illustration
*1 Temporary Bolt


d.

Tighten the temporary bolt and 5 bolts.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Connect the connector.


Hide 68102 24.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY

a.

Connect the cable to the negative (-) auxiliary battery terminal and power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal and power window regulator master switch.


c.
B307123

Insert the front door glass sub-assembly into the front door panel along the front door glass run as shown in the illustration.

NOTICE:

Do not damage the front door glass.



d.
B307088

Install the front door glass sub-assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.
B307087

Install the front door No. 2 service hole cover.


Hide 67831 25.INSTALL FRONT DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the front door panel.


b.

Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.


c.
B313978E02
0.427,0.396 0.302,0.396 false 3.063,0.396 3.146,0.396 false 2.969,2.875 2.969,3.021 false 0.115,0.302 0.292,0.469 0.177,0.167 10 true *a 3.167,0.281 3.344,0.448 0.177,0.167 10 true *a 2.875,3 3.052,3.167 0.177,0.167 10 true *a

Attach the front door service hole cover according to the reference points on the front door panel.

Text in Illustration
*a Reference Point

HINT:

Securely install the front door service hole cover preventing wrinkles and air bubbles.



Hide 86160P 27.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

Hide 28.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER

Hide 68172A 29.INSTALL FRONT DOOR GLASS INNER WEATHERSTRIP

a.
B307125

Engage the 8 claws to install the front door glass inner weatherstrip as shown in the illustration.


Hide 69206B 30.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B307084

Engage the 4 guides to install the front door inside handle sub-assembly.


Hide 67602 31.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY

a.
B307126E03
2.26,1.354 2.521,1.083 true 2.219,1.604 2.604,1.802 true 2.552,0.99 2.74,1.167 0.188,0.177 10 true *1 2.635,1.75 2.823,1.917 0.188,0.167 10 true *2

Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.

Text in Illustration
*1 Front Door Inside Locking Cable Assembly
*2 Front Door Lock Remote Control Cable Assembly


b.
B307169

Engage the 8 clips.


c.
B307081

Install the front door trim board sub-assembly with the 3 screws.


d.
B307127

Engage the claw and close the cover.


Hide 32.INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.

Connect the connector.


b.
B307078

Engage the 4 guides and 10 claws to install power window regulator master switch assembly with front door armrest base panel.


Hide 33.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.

Connect the connector.


b.
B307079

Engage the 4 guides and 10 claws to install power window regulator switch assembly with front door armrest base panel.


Hide 34.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 36.INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)