The vehicle approaching speaker controller receives stop light switch signals from the stop light switch assembly, vehicle speed signals from the combination meter assembly, engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the lower shift lever assembly, and produces the warning sound from the vehicle approaching speaker assembly.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1350 is not output | A |
| DTC B1350 is output | B |
| Communication with the GTS is not possible | C |
A
B
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE PROXIMITY NOTIFICATION SYSTEM>B1350)
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Proximity Sound (Vehicle Stationary) | Proximity sound (Vehicle stationary) | OFF or ON | Produces warning sound when vehicle is stopped |
| Result | Proceed to |
|---|---|
| The warning sound is produced | A |
| The warning sound is not produced | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light SW | Stop light switch / OFF or ON | OFF: Brake pedal released
ON: Brake pedal depressed |
- |
| Result | Proceed to |
|---|---|
| The GTS display changes according to brake pedal operation | A |
| The GTS display does not change according to brake pedal operation | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Vehicle Speed | Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Almost the same as actual vehicle speed | - |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the vehicle speed | A |
| The GTS display does not change according to the vehicle speed | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Oil Pressure SW | Oil pressure switch / OFF or ON | OFF: Engine started
ON: Engine not started |
- |
| Result | Proceed to |
|---|---|
| The GTS display changes according to engine operation | A |
| The GTS display does not change according to engine operation | B |
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Shift Position | P position switch / Not Parking or Parking | Not Parking or Parking | - |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the selected shift state | A |
| The GTS display does not change according to the selected shift state | B |
A
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL)
B
Disconnect the G25 lower shift lever assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G25-2 (P2) - Body ground | Power switch on (IG) | 8 V or higher |
| Power switch off | Below 1 V |
| *a | Front view of wire harness connector
(to Lower Shift Lever Assembly) |
OK
NG
Reconnect the G25 lower shift lever assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G25-2 (P2) - Body ground | Power switch on (IG), park (P) selected | 8 V or higher |
| Power switch on (IG), park (P) not selected | Below 2.5 V |
| *a | Component with harness connected
(Lower Shift Lever Assembly) |
OK
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL)
NG
Disconnect the G85 vehicle approaching speaker controller connector.
Disconnect the G25 lower shift lever assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G85-11 (SFTP) - G25-2 (P2) | Always | Below 1 Ω |
| G85-11 (SFTP) or G25-2 (P2) - Body ground | Always | 10 kΩ or higher |
OK
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL)
NG
Remove the vehicle approaching speaker assembly (see page Vehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER>REMOVAL).
Inspect the vehicle approaching speaker assembly (see page Vehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER>INSPECTION).
OK
NG
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER>REMOVAL)
Disconnect the G85 vehicle approaching speaker controller connector.
Disconnect the A64 vehicle approaching speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G85-3 (SP+) - A64-1 (+) | Always | Below 1 Ω |
| G85-8 (SP-) - A64-2 (-) | Always | Below 1 Ω |
| G85-3 (SP+) or A64-1 (+) - Body ground | Always | 10 kΩ or higher |
| G85-8 (SP-) or A64-2 (-) - Body ground | Always | 10 kΩ or higher |
OK
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL)
NG
Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed | On |
| Brake pedal released | Off |
OK
NG
Disconnect the G85 vehicle approaching speaker controller connector.
Disconnect the A65 stop light switch assembly connector.
Disconnect the M5 rear combination light assembly LH connector.
Disconnect the M6 rear combination light assembly RH connector.
Disconnect the S2 center stop light set connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G85-2 (STP) - A65-2 (OUT) | Always | Below 1 Ω |
| G85-2 (STP) or A65-2 (OUT) - Body ground | Always | 10 kΩ or higher |
OK
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL)
NG
Disconnect the G85 vehicle approaching speaker controller connector.
Disconnect the G1 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G85-6 (SPD) - G1-39 (+S) | Always | Below 1 Ω |
| G85-6 (SPD) or G1-39 (+S) - Body ground | Always | 10 kΩ or higher |
OK
NG
Reconnect the G85 vehicle approaching speaker controller connector.
Reconnect the G1 combination meter assembly connector.
Check the input waveform.
Remove the combination meter assembly with the connector(s) still connected.
Connect an oscilloscope to terminal G1-39 (+S) and body ground.
Turn the power switch on (IG).
Turn a wheel slowly.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Tool setting | 5 V/DIV., 20 ms./DIV. |
| Vehicle condition | Power switch on (IG), wheel being rotated |
| *a | Component with harness connected
(Combination Meter Assembly) |
The waveform is similar to that shown in the illustration.
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
OK
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL)
NG
Disconnect the G85 vehicle approaching speaker controller connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G85-12 (OPSW) - Body ground | Idling* | 8 V or higher |
| Power switch on (IG) | Below 2 V |
*:Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
| *a | Front view of wire harness connector
(to Vehicle Approaching Speaker Controller) |
OK
(See pageVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER ECU>REMOVAL)
NG
Disconnect the G85 vehicle approaching speaker controller connector.
Disconnect the E2 engine oil pressure switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G85-12 (OPSW) - E2-1 | Always | Below 1 Ω |
| G85-12 (OPSW) or E2-1 - Body ground | Always | 10 kΩ or higher |
OK
NG