Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM (w/ Occupant Classification System) › from 2017.06
RM2170E _58 Vehicle Interior _057041 SEAT BELT _0320196 SEAT BELT WARNING SYSTEM(w/ Occupant Classification System) J

SEAT BELT  SEAT BELT WARNING SYSTEM(w/ Occupant Classification System)  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The seat belt warning light on the combination meter assembly illuminates, blinks or turns off in accordance with the state of the front seat inner belt assembly LH.

WIRING DIAGRAM

B289103E58
5.458,1.833 6.76,2.281 1.302,0.448 10 false Front Seat Inner Belt Assembly LH 5.458,1.708 5.771,1.917 0.313,0.208 10 false M51 3.083,1.854 4.677,2.198 1.594,0.344 10 false Airbag Sensor Assembly 5.063,4.333 6.792,4.656 1.729,0.323 10 false : CAN Communication Line 0.229,1.729 1.885,2.229 1.656,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 0.448,4.208 1.656,4.677 1.208,0.469 10 false Combination Meter Assembly 3.083,1.708 3.385,1.938 0.302,0.229 10 false M57 4.448,1.115 4.667,1.438 0.219,0.323 10 false 10 5.385,1.115 5.573,1.375 0.188,0.26 10 false 2 5.385,0.323 5.594,0.594 0.208,0.271 10 false 1 4,0.417 4.427,0.688 0.427,0.271 10 false LBE- 4,1.219 4.427,1.448 0.427,0.229 10 false LBE+ 4.448,0.313 4.719,0.521 0.271,0.208 10 false 18 5.583,0.292 6,0.583 0.417,0.292 10 false LBE- 5.583,1.333 5.969,1.573 0.385,0.24 10 false LBE+

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)>HOW TO PROCEED WITH TROUBLESHOOTING).


HINT:

The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat. Check that the operation of the seat belt warning light is normal first.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)>ON-VEHICLE INSPECTION

If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


PROCEDURE

1.CHECK DTC OUTPUT (AIRBAG SYSTEM)

b.

Recheck for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / SRS Airbag / Data List.


e.

Read the Data List according to the display on the GTS.

SRS Airbag (Airbag Sensor Assembly)
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Left Side Buckle SW LH buckle switch/Unset, Set or NG Unset: Seat belt not fastened
Set: Seat belt fastened
NG: Data not determined
-

Result
Result Proceed to
Unset or Set is displayed on the GTS screen according to the driver seat belt condition A
Unset or Set is not displayed normally on the GTS screen according to the driver seat belt condition B
NG is displayed on the GTS screen C



A

3.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

C

3.REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Replace the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).



NEXT

4.CHECK SEAT BELT WARNING LIGHT
4.CHECK SEAT BELT WARNING LIGHT
a.

Check the operation of the seat belt warning light (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM (w/ Occupant Classification System)>ON-VEHICLE INSPECTION).

OK:

The seat belt warning light operates normally.




OK

END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY