Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0125  Insufficient Coolant Temperature for Closed Loop Fuel Control  


DESCRIPTION

Refer to DTC P0115.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0115

DTC No. DTC Detection Condition Trouble Area
P0125 The engine coolant temperature does not reach the closed loop enabling temperature for 20 minutes (this period varies with the engine coolant temperature at engine start) (2 trip detection logic).
·

Cooling system

·

Engine coolant temperature sensor

·

Water inlet with thermostat sub-assembly



MONITOR DESCRIPTION

The resistance of the engine coolant temperature sensor varies in proportion to the actual engine coolant temperature. The ECM supplies a constant voltage to the sensor and monitors the signal output voltage of the sensor. The signal output voltage varies according to the changing resistance of the sensor. After the engine is started, the engine coolant temperature is monitored by this signal. If the engine coolant temperature sensor indicates that the engine is not yet warm enough for closed loop fuel control, despite a specified period of time having elapsed since the engine was started, the ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.

Example:

When the engine coolant temperature is -3.33°C (26°F) or higher at engine start: After approximately 84 seconds of running time, the engine coolant temperature sensor still indicates that the engine is not warm enough to begin closed loop fuel (air fuel ratio feedback) control. The ECM interprets this as a malfunction in the sensor or cooling system and stores the DTC.

MONITOR STRATEGY

Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Leave the vehicle outside overnight.

2.

Connect the GTS to the DLC3.

3.

Turn the power switch on (IG) and turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

5.

Check that the engine coolant temperature is 10°C (50°F) or less.

6.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

7.

Turn the power switch off and wait for at least 30 seconds.

8.

Turn the power switch on (IG) and turn the GTS on.

9.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

10.

Start the engine.

11.

Wait 21 minutes or more.

12.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0125.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:
·

If any of DTCs P0115, P0117 or P0118 are output simultaneously with DTC P0125, the engine coolant temperature sensor may have an open or a short circuit. Troubleshoot those DTCs first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0125)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0125 is output A
DTC P0125 and other DTCs are output B

HINT:

If any DTCs other than P0125 are output, troubleshoot those DTCs first.




A

2.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

B

2.INSPECT WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
a.

Inspect the water inlet with thermostat sub-assembly (thermostat opening temperature).

Click hereEngine / Hybrid System>1NZ-FXE (COOLING)>THERMOSTAT>INSPECTION



OK

3.CHECK COOLING SYSTEM

NG

REPLACE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

3.CHECK COOLING SYSTEM
a.

Check for defects in the cooling system that might cause the system to be too cold, such as abnormal cooling fan operation or any modifications.

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

NG

REPAIR OR REPLACE COOLING SYSTEM