Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2017.06
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0403  Exhaust Gas Recirculation Circuit  


DESCRIPTION

Refer to DTC P0401.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0401

DTC No. DTC Detection Condition Trouble Area
P0403 Open or short in EGR valve circuit (1 trip detection logic).
·

Open or short in EGR valve assembly circuit

·

EGR valve assembly

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the EGR valve assembly circuit.

Example:

·

If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, but the step motor is still operating, the ECM determines that there is a short in the EGR valve assembly circuit, and stores the DTC.

·

If the EGR1, EGR2, EGR3 or EGR4 terminal output voltage is excessively low, and the step motor is not operating, the ECM determines that there is an open in the EGR valve assembly circuit, and stores the DTC.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A215251E43
2.323,2.906 2.969,3.292 0.646,0.385 10 false Warming Up 3.406,2.896 4.292,3.146 0.885,0.25 10 false 10 minutes 1.99,2.094 2.281,2.344 0.292,0.25 10 false [A] 2.49,1.813 2.802,2.042 0.313,0.229 10 false [B] 3.781,0.688 4.115,0.917 0.333,0.229 10 false [C] 4.438,3.292 4.74,3.531 0.302,0.24 10 false [D] 0.729,0.844 2.01,1.219 1.281,0.375 10 false 20 km/h or more 1.417,1.927 1.927,2.188 0.51,0.26 10 false Idling 0.51,2.229 1.906,2.698 1.396,0.469 10 false Power Switch on (IG)

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the GTS on [A].

6.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

7.

Start the engine and warm it up [B].

8.

Drive the vehicle at 20 km/h (12 mph) or more for 10 minutes [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0403.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system has a normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A275605E05
1.833,5.219 3.188,5.385 1.354,0.167 10 false EGR Valve Assembly 0.74,4.729 1.375,5.073 0.635,0.344 10 false Auxiliary Battery 0.646,3.865 1.313,4.021 0.667,0.156 10 false MAIN 2.698,1.354 3.51,1.688 0.813,0.333 10 false EFI-MAIN 2.042,0.823 2.719,0.979 0.677,0.156 10 false EFI-MAIN 5.875,1.104 6.313,1.26 0.438,0.156 10 false MREL 5.521,1.104 5.823,1.26 0.302,0.156 10 false A40 5.594,0.927 5.781,1.083 0.188,0.156 10 false 46 1.479,5.219 1.781,5.375 0.302,0.156 10 false C18 5.563,2.74 5.781,2.896 0.219,0.156 10 false 28 5.563,3.125 5.781,3.281 0.219,0.156 10 false 27 5.563,3.521 5.781,3.677 0.219,0.156 10 false 26 5.563,3.917 5.781,4.073 0.219,0.156 10 false 25 3.094,2.823 3.24,2.979 0.146,0.156 10 false 4 3.094,3.208 3.24,3.365 0.146,0.156 10 false 3 3.094,3.604 3.24,3.76 0.146,0.156 10 false 6 3.094,4.385 3.24,4.542 0.146,0.156 10 false 2 3.083,4.76 3.229,4.917 0.146,0.156 10 false 5 3.094,4 3.24,4.156 0.146,0.156 10 false 1 5.875,2.917 6.281,3.073 0.406,0.156 10 false EGR1 5.875,3.302 6.281,3.458 0.406,0.156 10 false EGR2 5.875,3.688 6.281,3.844 0.406,0.156 10 false EGR3 5.875,4.083 6.281,4.24 0.406,0.156 10 false EGR4 2.625,2.823 3.042,2.979 0.417,0.156 10 false EGR1 2.625,3.208 3.042,3.365 0.417,0.156 10 false EGR2 2.625,3.604 3.042,3.76 0.417,0.156 10 false EGR3 2.74,4.396 3.031,4.552 0.292,0.156 10 false +B2 2.75,4.771 3.031,4.927 0.281,0.156 10 false +B1 2.625,4 3.042,4.156 0.417,0.156 10 false EGR4 5.51,4.083 5.781,4.24 0.271,0.156 10 false C10 5.51,3.688 5.781,3.844 0.271,0.156 10 false C10 5.51,3.302 5.781,3.458 0.271,0.156 10 false C10 5.51,2.917 5.781,3.073 0.271,0.156 10 false C10 0.656,2.885 0.969,3.042 0.313,0.156 10 false P/I 6.125,4.781 6.458,4.938 0.333,0.156 10 false ECM 1.729,0.698 1.969,0.875 0.24,0.177 10 false 2E 1.729,1.104 1.969,1.281 0.24,0.177 10 false 2C 3.542,1.104 3.781,1.281 0.24,0.177 10 false 2C 3.542,0.688 3.781,0.865 0.24,0.177 10 false 2C 1.781,0.5 1.938,0.646 0.156,0.146 10 false 1 1.781,0.917 1.906,1.115 0.125,0.198 10 false 2 3.604,0.917 3.729,1.115 0.125,0.198 10 false 3 3.594,0.5 3.698,0.656 0.104,0.156 10 false 4 2.031,1.729 3.583,1.885 1.552,0.156 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Primary / Throttle Idle Position and MAP.


g.

Confirm that the Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position when Throttle Idle Position is ON in Data List.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.





OK

NG

2.INSPECT EGR VALVE ASSEMBLY
2.INSPECT EGR VALVE ASSEMBLY
a.

Inspect the EGR valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE EMISSION CONTROL>EGR VALVE>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EGR VALVE ASSEMBLY)
a.
U158849E02
1.802,2.052 2.625,1.188 false 2.615,2.906 1.802,2.354 false 0.344,1.885 0.677,2.063 0.333,0.177 10 false C18 0.229,0.188 0.448,0.365 0.219,0.177 10 false *a 2.667,2.823 2.99,3 0.323,0.177 10 false +B1 2.656,1.052 2.979,1.229 0.323,0.177 10 false +B2

Disconnect the EGR valve assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C18-5 (+B1) - Body ground Power switch on (IG) 11 to 14 V
C18-2 (+B2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to EGR Valve Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - ECM)
a.

Disconnect the EGR valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C18-4 (EGR1) - C10-28 (EGR1) Always Below 1 Ω
C18-3 (EGR2) - C10-27 (EGR2) Always Below 1 Ω
C18-6 (EGR3) - C10-26 (EGR3) Always Below 1 Ω
C18-1 (EGR4) - C10-25 (EGR4) Always Below 1 Ω
C18-4 (EGR1) or C10-28 (EGR1) - Body ground Always 10 kΩ or higher
C18-3 (EGR2) or C10-27 (EGR2) - Body ground Always 10 kΩ or higher
C18-6 (EGR3) or C10-26 (EGR3) - Body ground Always 10 kΩ or higher
C18-1 (EGR4) or C10-25 (EGR4) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EGR VALVE ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the EGR valve assembly connector.


b.

Remove the No. 1 integration relay and ENG W/PMP relay from the No. 2 engine room relay block and No. 2 junction block assembly.

HINT:

Remove the ENG W/PMP relay connected between the checked terminals as the coil inside the relay influences the measurement value.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C18-5 (+B1) - 2C-4 Always Below 1 Ω
C18-2 (+B2) - 2C-4 Always Below 1 Ω
C18-5 (+B1) or 2C-4 - Body ground Always 10 kΩ or higher
C18-2 (+B2) or 2C-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR