Home › Engine / Hybrid System › 1NZ-FXE FUEL › FUEL SYSTEM › from 2017.06
RM2170E _51 Engine / Hybrid System _057006 1NZ-FXE FUEL _0277958 FUEL SYSTEM L

1NZ-FXE FUEL  FUEL SYSTEM  PRECAUTION  


PRECAUTIONS


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY(for Separate Type Seatback)>REMOVAL


b.

Remove the rear floor service hole cover and butyl tape.


c.
A408560C01
0.063,0.031 0.385,0.229 0.323,0.198 12 false *A 0.083,2.281 0.406,2.49 0.323,0.208 12 false *B
*A w/ Canister Pump Module
*B w/o Canister Pump Module


Disconnect the fuel pump connector.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE


e.

Start the engine.


f.

After the engine has stopped on its own, turn the power switch off.


g.

Crank the engine again and make sure that the engine does not start.

HINT:

Some DTCs may be stored. Clear the DTCs before proceeding to the next step.




h.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



i.

Loosen the fuel tank cap assembly, then discharge the pressure in the fuel tank assembly completely.


j.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


k.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


l.

Connect the fuel pump connector.


m.

Install the rear floor service hole cover with new butyl tape.


n.


FUEL SYSTEM


a.

When disconnecting a high pressure fuel line, a large amount of gasoline will spill out, so perform the following procedure:

i.

Discharge the fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.


v.

Put a container under the connecting parts.



b.

Perform the following procedure when disconnecting a fuel tube connector (quick type A):

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A264997

Remove the No. 1 fuel pipe clamp.


ii.

Check that there is no foreign matter around the fuel tube connector before disconnecting it. Clean it if necessary.


iii.
A314711C03
2.385,1.615 2.875,1.99 2.875,1.99 2.646,1.604 false 2.24,3.01 2.375,3.01 2.375,3.01 2.438,3.417 false 2.677,3.5 2.865,3.042 2.865,3.042 2.979,3.042 false 2.375,4.188 2.375,3.979 false 1.667,4.292 2.063,4.292 2.063,4.292 2.063,3.813 false 1.896,4.292 1.896,3.802 false 1,2.979 1.146,2.979 1.146,2.979 1.365,3.458 false 2.927,1.958 3.24,2.115 0.313,0.156 10 false *a 1.5,4.219 1.813,4.375 0.313,0.156 10 false *b 2.302,4.208 2.615,4.365 0.313,0.156 10 false *c 0.813,2.906 1.125,3.063 0.313,0.156 10 false *d 3.031,2.969 3.344,3.125 0.313,0.156 10 false *e 2.083,2.927 2.396,3.083 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Pinch
V100136

Pull off


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



iv.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




v.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vi.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Perform the following procedure when connecting a fuel tube connector (quick type A):

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.

Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.
A303841C01
1.542,1.563 1.698,1.76 0.156,0.198 10 false .
V100135

Pull


After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.



iv.

Install the No. 1 fuel pipe clamp.



d.

Perform the following procedure when disconnecting a fuel tube connector (quick type B):

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A268444C02
1.208,2.833 0.99,2.833 false 2.427,2.833 2.229,3.031 2.229,3.031 2.146,3.031 false 0.781,2.75 1.052,2.938 0.271,0.188 10 false *a 1.938,2.958 2.219,3.135 0.281,0.177 10 false *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.
A308190C01
1.719,2.052 1.719,1.667 false 1.5,2.052 1.875,2.052 1.875,2.052 1.875,1.656 false 2.083,1.177 1.969,0.729 1.969,0.729 1.813,0.729 false 2.26,1.26 2.385,0.76 2.385,0.76 2.521,0.76 false 2.802,1.938 2.635,1.938 2.635,1.938 2.323,1.583 false 2.573,0.667 2.885,0.823 0.313,0.156 10 false *a 1.313,1.958 1.625,2.115 0.313,0.156 10 false *b 1.656,0.635 1.969,0.792 0.313,0.156 10 false *c 2.844,1.844 3.177,2 0.333,0.156 10 false *d
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Fuel Pipe


If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).




iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Perform the following procedure when connecting a fuel tube connector (quick type B):

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A308191C01
0.927,3.104 1.073,3.104 1.073,3.104 1.24,2.854 false 2.052,2.729 2.406,2.729 false 0.76,3.01 1.073,3.167 0.313,0.156 10 false *a 1.875,2.646 2.188,2.802 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.





FUEL INJECTOR ASSEMBLY


a.
A264992C09
2.656,0.281 2.802,0.115 2.802,0.115 2.896,0.115 false 2.521,0.594 2.823,0.896 2.823,0.896 2.927,0.896 false 1.427,1.802 1.615,1.99 1.615,1.99 1.719,1.99 false 2.99,0.063 3.198,0.292 0.208,0.229 10 false *1 1.771,1.938 2.031,2.156 0.26,0.219 10 false *3 2.979,0.833 3.25,1.031 0.271,0.198 10 false *2
*1 Fuel Delivery Pipe
*2 O-ring
*3 Injector Vibration Insulator


Install the fuel injector assembly to the cylinder head sub-assembly as shown in the illustration.

i.

Do not reuse the injector vibration insulator.



b.
A264991C10
0.135,0.104 3.219,1.385 3.083,1.281 0.135,1.469 3.219,3.208 3.083,1.74 0.76,0.906 0.76,1.177 false 1.135,1.083 1.135,1.188 false 0.74,2.365 0.74,2.708 false 1.135,2.552 1.135,2.708 false 0.677,1.188 0.917,1.365 0.24,0.177 10 false *1 0.656,2.74 0.927,2.948 0.271,0.208 10 false *1 1.042,1.188 1.333,1.396 0.292,0.208 10 false *2 1.052,2.74 1.417,2.958 0.365,0.219 10 false *2 0.198,1.521 0.365,1.698 0.167,0.177 10 false *b 0.198,0.146 0.365,0.323 0.167,0.177 10 false *a
*1 O-ring
*2 Fuel Delivery Pipe
*a Correct
*b Incorrect


Observe the following precautions when removing and installing the fuel injector assembly.

i.

Do not reuse the O-ring.


ii.

When installing a new O-ring to the fuel injector assembly, do not damage the O-ring.


iii.

Apply gasoline or spindle oil to a new O-ring before installing it.

NOTICE:

Do not use engine oil, gear oil or brake fluid.





FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY (w/ Canister Pump Module)


NOTICE:
·
A431048C01
1.896,1.063 2.344,0.698 2.344,0.698 2.521,0.698 true 2.615,0.625 2.927,0.823 0.313,0.198 10 false *a
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.




FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY (w/o Canister Pump Module)


NOTICE:
·
A431049C01
0.646,3.729 0.948,3.729 false 0.615,1.167 0.917,1.167 false 0.073,0.073 0.406,0.271 0.333,0.198 12 false *A 0.104,2.323 0.427,2.563 0.323,0.24 12 false *B 0.385,1.073 0.698,1.229 0.313,0.156 10 false *a 0.406,3.646 0.719,3.802 0.313,0.156 10 false *a
*A for Type A
*B for Type B
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>1NZ-FXE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION