Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › from 2017.06
RM2170E _55 Steering _057028 STEERING GEAR / LINKAGE _0278051 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


PROCEDURE

Hide 1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2. SECURE STEERING WHEEL

a.
C247537

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 4.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 5.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C251686E01
0.547,0.276 0.685,0.455 0.137,0.179 10 B 2.948,1.741 3.085,1.920 0.137,0.179 10 A 0.696,0.364 1.446,0.364 false 2.249,1.834 2.925,1.834 false

Remove clip (A), detach clip (B) from the vehicle body and disconnect the No. 1 steering column hole cover sub-assembly.

NOTICE:

Do not damage clip (B).



Hide 6.REMOVE FRONT WHEELS

Hide 7.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (Integrated Cover Type)

Hide 48810 8.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 9.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 10.SEPARATE TIE ROD END SUB-ASSEMBLY LH

a.

Remove the cotter pin and nut.


b.
C249937E03
2.723,0.907 3.046,1.087 0.323,0.181 10 SST 2.461,1.294 2.461,0.99 2.461,0.99 2.707,0.99 false

Install SST to the tie rod end.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure that the upper end of the tie rod end and SST are aligned.



c.

Secure SST using a string.

NOTICE:

Be sure to tighten the string firmly to secure SST to the steering knuckle to prevent SST from falling off.



d.

Using SST, separate the tie rod end from the steering knuckle.

SST
09960-20010  (09961-02060)

C249935C08
0.938,0.604 0.938,0.208 0.938,0.208 1.354,0.208 false 0.948,2.167 0.948,2.396 0.948,2.396 0.792,2.396 false 3.76,2.021 3.76,2.333 3.76,2.333 3.604,2.333 false 0.635,2.313 0.823,2.521 0.188,0.208 10 false *a 6.656,0.344 6.938,0.573 0.281,0.229 10 false *c 1.729,1.938 1.854,2.104 0.125,0.167 10 false B 1.729,1.729 1.854,1.896 0.125,0.167 10 false A 1.396,0.125 1.552,0.292 0.156,0.167 10 false *b 6.667,2.052 6.865,2.24 0.198,0.188 10 false *d 3.313,2.25 3.604,2.427 0.292,0.177 10 false SST 6.656,0.677 6.938,0.906 0.281,0.229 10 false *c
*a Center Nut *b String
*c Grease Application Area *d Place the wrench here


CAUTION:

Apply grease to the bolt threads and the tip of SST.


NOTICE:
·

Be sure to tighten the string firmly to secure SST to the steering knuckle LH to prevent SST from falling off.

·

Install SST with the center nut so that (A) and (B) shown in the illustration are parallel. Otherwise, the ball joint dust cover may be damaged.

·

Be sure to place the wrench on the part shown in the illustration.

·

Do not damage the front disc brake dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle LH.




Hide 45046 11.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 12.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 13.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51201 14.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 45025D 15.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.
C251700

Remove the No. 1 steering column hole cover sub-assembly from the steering link assembly.


Hide 16.REMOVE STEERING LINK ASSEMBLY

a.
C244486

Remove the 2 bolts, 2 nuts and steering link assembly from the front suspension crossmember sub-assembly.

NOTICE:

Keep the nut from rotating while turning the bolt because the nut has its own stopper.



Hide 17.SECURE STEERING LINK ASSEMBLY

a.
C251687C02
1.51,0.604 1.51,0.344 1.51,0.344 1.854,0.344 false 1.719,1.083 2.427,1.604 2.427,1.604 2.542,1.604 true 1.885,0.26 2.198,0.448 0.313,0.188 10 false SST 2.573,1.521 2.885,1.708 0.313,0.188 10 false *a
*a Protective Tape


Using SST, secure the steering link assembly in a vise.

SST
09612-00012  

HINT:

Tape SST before use.



Hide 45047 18.REMOVE TIE ROD END SUB-ASSEMBLY LH

a.
C187022C16
0.99,1.219 0.99,1.573 0.99,1.573 1.583,1.573 true 1.365,1.219 1.365,1.573 true 1.594,1.469 1.781,1.625 0.188,0.156 10 false *a
*a Matchmark


Put matchmarks on the tie rod end sub-assembly LH and steering gear assembly.


b.

Remove the tie rod end sub-assembly LH and lock nut.


Hide 45046 19.REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.