Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › from 2017.06
RM2170E _53 Suspension _057017 FRONT SUSPENSION _0278010 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  REMOVAL  


PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2. SECURE STEERING WHEEL

Hide 45259A 3.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 4.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 5.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 6.REMOVE FRONT WHEEL

Hide 7.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY (Integrated Cover Type)

Hide 48810 8.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

a.
C249871

Remove the nut and separate the front stabilizer link assembly LH from the front stabilizer bar.

HINT:

Use a hexagon socket wrench to hold the stud.



Hide 48820B 9.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 45047 10.SEPARATE TIE ROD END SUB-ASSEMBLY LH

Hide 45046 11.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 48069 12.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 13.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 51201 14.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C249868C04
2.438,2.281 2.354,2.281 2.354,2.281 2.063,1.917 false 1.75,0.844 2.042,0.135 2.042,0.135 2.167,0.135 true 2.469,2.198 2.688,2.417 0.219,0.219 10 false *a 2.208,0.052 2.427,0.271 0.219,0.219 10 false *b
*a Jack
*b Wooden Block
V100135

Front of the Vehicle
V100155

Wooden Block Placement Location


Using a jack and a wooden block, support the engine and transaxle assembly.


b.
C249869

Remove the bolt and separate the engine moving control rod.


c.
C249867C07
0.281,1.917 2.542,1.917 2.542,1.917 2.542,1.427 true 3.177,2.115 3.094,2.115 3.094,2.115 2.969,1.719 false 2.083,1.917 2.083,1.354 true 1.26,1.917 1.26,1.49 true 0.719,1.917 0.719,1.531 true 0.115,1.833 0.313,2.021 0.198,0.188 10 false *b 3.219,2.031 3.427,2.25 0.208,0.219 10 false *a
*a Engine Lifter
*b Attachment
V100135

Front of the Vehicle
V100155

Attachment Placement Location


Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

NOTICE:
·

Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

·

Use the attachments to keep the front suspension crossmember sub-assembly level.

·

The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.




d.

Remove the 6 bolts and front suspension crossmember sub-assembly.

C249876


e.

Slowly lower the front suspension crossmember sub-assembly.

NOTICE:

When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.



Hide 15.REMOVE STEERING LINK ASSEMBLY

Hide 48829A 16.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 17.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as the LH side.


Hide 48811 18.REMOVE FRONT STABILIZER BAR

Hide 48069 19.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C235698

Remove the bolt and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.


Hide 48068 20.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as the LH side.


Hide 12363A 21.REMOVE ENGINE MOVING CONTROL ROD

a.
C213122

Remove the bolt and engine moving control rod from the front suspension crossmember sub-assembly.