Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › from 2017.06
RM2170E _59 Vehicle Exterior _057045 WINDOW / GLASS _0278147 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Driver Side Power Window does not Operate with Power Window Master Switch  


DESCRIPTION

When the power switch is on (IG), the power window regulator motor assembly (for driver door) is operated by the power window regulator master switch assembly. The power window regulator motor assembly (for driver door) has motor, regulator and ECU functions.

WIRING DIAGRAM

for LHD


B281016E63
0.271,2.292 2.281,2.708 2.01,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,3.365 2.615,3.521 1.646,0.156 10 false : LIN Communication Line 0.417,0.531 1.323,0.875 0.906,0.344 10 false from Auxiliary Battery 1.854,0.667 2.469,0.823 0.615,0.156 10 false DOOR D 2.521,2.406 4.573,2.813 2.052,0.406 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.417 6.844,2.781 1.615,0.365 10 false Power Window Regulator Master Switch Assembly 2.521,2.25 3.531,2.406 1.01,0.156 10 false J3 5.229,2.25 5.948,2.406 0.719,0.156 10 false J1 1.635,1.594 2.01,1.75 0.375,0.156 10 false LIN2 2.833,1.448 3.094,1.604 0.26,0.156 10 false LIN 2.833,0.427 2.958,0.583 0.125,0.156 10 false B 3.802,0.427 4.208,0.583 0.406,0.156 10 false AUTO 5.375,0.521 5.802,0.677 0.427,0.156 10 false AUTO 5.375,1.031 5.51,1.188 0.135,0.156 10 false D 5.375,1.531 5.51,1.688 0.135,0.156 10 false U 5.375,1.833 5.51,1.99 0.135,0.156 10 false E 3.729,0.927 4.24,1.083 0.51,0.156 10 false DOWN 3.958,1.438 4.208,1.594 0.25,0.156 10 false UP 3.875,1.729 4.24,1.885 0.365,0.156 10 false GND 4.24,1.729 4.365,1.885 0.125,0.156 10 false 1 4.25,0.938 4.375,1.094 0.125,0.156 10 false 7 4.792,0.938 5.479,1.104 0.688,0.167 10 false 5*1, 3*2 4.781,1.448 5.281,1.604 0.5,0.156 10 false 8*1, 6*2 5.188,1.74 5.677,1.896 0.49,0.156 10 false 1 4.25,0.427 4.375,0.583 0.125,0.156 10 false 4 5.208,0.427 5.333,0.583 0.125,0.156 10 false 4 4.229,1.448 4.417,1.604 0.188,0.156 10 false 10 2.646,0.427 2.771,0.583 0.125,0.156 10 false 2 2.635,1.448 2.813,1.604 0.177,0.156 10 false 9 3.188,3.167 5.677,3.344 2.49,0.177 10 false *1: w/o Canister Pump Module 3.188,3.448 5.677,3.625 2.49,0.177 10 false *2: w/ Canister Pump Module


for RHD


B281016E65
0.271,2.292 2.281,2.708 2.01,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.969,3.365 2.615,3.521 1.646,0.156 10 false : LIN Communication Line 0.417,0.531 1.323,0.875 0.906,0.344 10 false from Auxiliary Battery 1.854,0.667 2.469,0.823 0.615,0.156 10 false DOOR D 2.521,2.406 4.573,2.813 2.052,0.406 10 false Power Window Regulator Motor Assembly (for Driver Door) 5.229,2.406 6.844,2.771 1.615,0.365 10 false Power Window Regulator Master Switch Assembly 2.521,2.25 3.531,2.406 1.01,0.156 10 false H3 5.229,2.25 5.948,2.406 0.719,0.156 10 false H1 1.635,1.594 2.01,1.75 0.375,0.156 10 false LIN2 2.833,1.448 3.094,1.604 0.26,0.156 10 false LIN 2.833,0.427 2.958,0.583 0.125,0.156 10 false B 3.802,0.427 4.208,0.583 0.406,0.156 10 false AUTO 5.375,0.531 5.802,0.688 0.427,0.156 10 false AUTO 5.375,1.042 5.51,1.198 0.135,0.156 10 false D 5.375,1.542 5.51,1.698 0.135,0.156 10 false U 5.375,1.833 5.51,1.99 0.135,0.156 10 false E 3.729,0.927 4.24,1.083 0.51,0.156 10 false DOWN 3.958,1.438 4.208,1.594 0.25,0.156 10 false UP 3.875,1.729 4.24,1.885 0.365,0.156 10 false GND 4.25,1.729 4.375,1.885 0.125,0.156 10 false 1 4.25,0.938 4.375,1.094 0.125,0.156 10 false 7 5.177,0.917 5.302,1.073 0.125,0.156 10 false 5 5.177,1.438 5.677,1.594 0.5,0.156 10 false 1 5.188,1.729 5.677,1.885 0.49,0.156 10 false 9 4.25,0.427 4.375,0.583 0.125,0.156 10 false 4 5.188,0.427 5.313,0.583 0.125,0.156 10 false 4 4.25,1.448 4.438,1.604 0.188,0.156 10 false 10 2.646,0.427 2.771,0.583 0.125,0.156 10 false 2 2.635,1.448 2.813,1.604 0.177,0.156 10 false 9


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If a power window regulator motor assembly (for driver door) has been replaced with a new one, initialize the power window control system.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION

·

When the ECU determines that the power window regulator motor assembly (for driver door) has a malfunction, DTC B2311 is stored.



PROCEDURE

1.READ VALUE USING GTS (MAIN BODY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch to on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Communication D-Door Motor Connection status between power window regulator motor assembly (for driver door) and main body ECU (multiplex network body ECU) / OK or STOP STOP or OK STOP: Communication stopped
OK: Normal communication
-

OK:

On the GTS screen, OK is displayed.




OK

2.READ VALUE USING INTELLIGENT TESTER (D-DOOR MOTOR)

NG

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting)

2.READ VALUE USING INTELLIGENT TESTER (D-DOOR MOTOR)
a.

Enter the following menus: Body / D-Door Motor / Data List.


b.

Read the Data List according to the display on the GTS.

D-Door Motor
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal OFF or ON OFF: Driver door power window manual up switch not operated
ON: Driver door power window manual up switch operated
-
D Door P/W Down SW Driver door power window manual down switch signal OFF or ON OFF: Driver door power window manual down switch not operated
ON: Driver door power window manual down switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

3.PERFORM ACTIVE TEST USING GTS (D-DOOR MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
3.PERFORM ACTIVE TEST USING GTS (D-DOOR MOTOR)
a.

Enter the following menus: Body / D-Door Motor / Active Test.


b.

Perform the Active Test according to the display on the GTS.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


D-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

OK:

Driver door power window operates normally.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR (FOR DRIVER DOOR) - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the power window regulator motor assembly (for driver door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

i.

for LHD

Standard Voltage:
Tester Connection Condition Specified Condition
J3-2 (B) - Body ground Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
J3-1 (GND) - Body ground Always Below 1 Ω



ii.

for RHD

Standard Voltage:
Tester Connection Condition Specified Condition
H3-2 (B) - Body ground Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
H3-1 (GND) - Body ground Always Below 1 Ω





OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER WINDOW REGULATOR MOTOR (FOR DRIVER) AND BODY GROUND)
a.

Disconnect the power window regulator master switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

i.

for LHD

Standard Resistance:
Tester Connection Condition Specified Condition
J1-8 (U) - J3-10 (UP)*1
J1-6 (U) - J3-10 (UP)*2
Always Below 1 Ω
J1-5 (D) - J3-7 (DOWN)*1
J1-3 (D) - J3-7 (DOWN)*2
Always Below 1 Ω
J1-8 (U) - Body ground*1
J1-6 (U) - Body ground*2
Always 10 kΩ or higher
J1-5 (D) - Body ground*1
J1-3 (D) - Body ground*2
Always 10 kΩ or higher
J1-1 (E) - Body ground Always Below 1 Ω


*1: w/o Canister Pump Module

*2: w/ Canister Pump Module



ii.

for RHD

Standard Resistance:
Tester Connection Condition Specified Condition
H1-1 (U) - H3-10 (UP) Always Below 1 Ω
H1-5 (D) -H3-7 (DOWN) Always Below 1 Ω
H1-1 (U) - Body ground Always 10 kΩ or higher
H1-5 (D) - Body ground Always 10 kΩ or higher
H1-9 (E) - Body ground Always Below 1 Ω





OK

6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.
B298969C28
1.073,0.844 1.115,1.656 false 1.677,1.792 1.458,2.635 false 1.219,1.792 0.948,2.656 false 2.344,0.844 2.313,1.656 false 1.865,0.854 2.01,1.677 false 1.563,1.656 1.396,0.573 false 0.198,0.083 0.385,0.271 0.188,0.188 10 false *a 0.927,0.646 1.417,0.833 0.49,0.188 10 false E*C 2.25,0.5 2.833,0.688 0.583,0.188 10 false E*A*B 0.76,2.688 1.271,2.865 0.51,0.177 10 false U*A 1.281,2.667 2.135,2.854 0.854,0.188 10 false D*A*C 1.729,0.667 2.583,0.854 0.854,0.188 10 false D*B 2.25,0.667 2.833,0.854 0.583,0.188 11 false U*C 1.271,0.385 1.729,0.583 0.458,0.198 10 false U*B
*A for LHD and w/o Canister Pump Module
*B for LHD and w/ Canister Pump Module
*C for RHD
*a Component without harness connected
(Power Window Regulator Master Switch Assembly)


Remove the power window regulator master switch assembly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

i.

for LHD

Standard Resistance:
Tester Connection Switch Condition Specified Condition
8 (U) - 1 (E)*1
6 (U) - 1 (E)*2
Manual UP Below 1 Ω
5 (D) - 1 (E)*1
3 (D) - 1 (E)*2
Manual DOWN Below 1 Ω


*1: w/o Canister Pump Module

*2: w/ Canister Pump Module



ii.

for RHD

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (U) - 9 (E) Manual UP Below 1 Ω
5 (D) - 9 (E) Manual DOWN Below 1 Ω





OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY