Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2017.06
RM2170E _58 Vehicle Interior _057042 HEATING / AIR CONDITIONING _0278125 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B14A2  Driver Side Solar Sensor Short Circuit  


DESCRIPTION

E107008E41
0.573,0.125 2.25,0.375 1.677,0.25 10 false Resistance of Photodiode 0.521,0.708 0.979,0.958 0.458,0.25 10 false High 0.583,2.427 1.042,2.698 0.458,0.271 10 false Low 0.917,2.646 1.438,2.896 0.521,0.25 10 false Weak 2.385,2.615 2.938,2.885 0.552,0.271 10 false Strong 0.979,2.969 2.719,3.208 1.74,0.24 10 false Strength of Solar Radiation

The cooler thermistor (solar sensor) is installed on the upper side of the instrument panel. It detects sunlight and creates a signal that is used for air conditioning control in AUTO mode. The output voltage from the cooler thermistor (solar sensor) varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier assembly detects changes in the output voltage from the cooler thermistor (solar sensor).

DTC No. DTC Detection Condition Trouble Area
B14A2 Short in cooler thermistor (solar sensor) circuit
·

Automatic light control sensor*1

·

Cooler thermistor (solar sensor)*2

·

Harness or connector

·

Air conditioning amplifier assembly

·

Main body ECU (multiplex network body ECU)*1



*1: w/ Automatic Light Control

*2: w/o Automatic Light Control


WIRING DIAGRAM

E239510E06
0.625,3.667 2.635,3.885 2.01,0.219 10 false Automatic Light Control Sensor 4.604,3.615 6.958,3.854 2.354,0.24 10 false Air Conditioning Amplifier Assembly 4.573,2.01 6.74,2.406 2.167,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 0.615,3.49 0.948,3.677 0.333,0.188 10 false G90 4.563,1.823 4.896,2.01 0.333,0.188 10 false G59 4.604,3.427 4.938,3.615 0.333,0.188 10 false G34 1.823,1.073 2.26,1.281 0.438,0.208 10 false CLTE 1.823,1.531 2.26,1.74 0.438,0.208 10 false CLTB 4.938,1.073 5.375,1.281 0.438,0.208 10 false CLTE 4.958,1.531 5.396,1.74 0.438,0.208 10 false CLTB 1.917,3.01 2.354,3.219 0.438,0.208 10 false TSD 4.938,3.031 5.375,3.24 0.438,0.208 10 false TS 2.313,0.938 2.646,1.125 0.333,0.188 10 false 5 2.313,1.396 2.646,1.583 0.333,0.188 10 false 3 4.656,0.938 4.99,1.125 0.333,0.188 10 false 22 4.656,1.406 4.99,1.594 0.333,0.188 10 false 20 4.635,2.896 4.969,3.083 0.333,0.188 10 false 33 2.333,2.865 2.667,3.052 0.333,0.188 10 false 1 0.135,0.146 2.281,0.417 2.146,0.271 12 false w/ Automatic Light Control:

E248685E09
5.219,1.052 5.813,1.313 0.594,0.26 10 false S5-4 4.948,0.948 5.354,1.208 0.406,0.26 10 false 30 4.948,1.438 5.396,1.656 0.448,0.219 10 false 33 5.219,1.542 5.771,1.74 0.552,0.198 10 false TS 2.427,0.948 2.729,1.25 0.302,0.302 10 false 1 2.427,1.427 2.781,1.677 0.354,0.25 10 false 2 2.083,0.927 2.552,1.177 0.469,0.25 10 false SS+ 2.073,1.417 2.521,1.667 0.448,0.25 10 false SS- 0.656,2.219 3.26,2.458 2.604,0.24 10 false Cooler Thermistor (Solar Sensor) 0.656,2.063 0.927,2.24 0.271,0.177 10 false G61 4.635,2.167 7.156,2.344 2.521,0.177 10 false Air Conditioning Amplifier Assembly 4.625,2.01 5.281,2.292 0.656,0.281 10 false G34 0.219,0.135 2.438,0.375 2.219,0.24 12 false w/o Automatic Light Control:

PROCEDURE

1.READ VALUE USING TECHSTREAM
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solar Sensor (D Side) Solar sensor /
Min.: 0
Max.: 255
Solar sensor value increases as brightness increases -

OK:

The display is as specified in the Normal Condition column.



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.CONFIRM MODEL
2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Automatic Light Control A
w/o Automatic Light Control B



A

6.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E373252C01
1.469,0.396 1.927,0.625 0.458,0.229 0.917,1.083 1.083,1.083 1.083,1.083 1.625,1.333 false 2.646,1.052 2.521,1.052 2.521,1.052 1.823,1.323 false 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a 0.583,1.01 0.896,1.208 0.313,0.198 10 false SS+ 2.729,0.979 3.042,1.177 0.313,0.198 10 false SS- 1.563,0.427 1.875,0.625 0.313,0.198 10 false G61
*a Front view of wire harness connector
(to Cooler Thermistor (Solar Sensor))


Disconnect the G61 cooler thermistor (solar sensor) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G61-1 (SS+) - G61-2 (SS-) Ignition switch off Below 1 V
G61-1 (SS+) - G61-2 (SS-) Ignition switch ON (IG) 4.75 to 5.25 V




OK

4.INSPECT COOLER THERMISTOR (SOLAR SENSOR)

NG

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER THERMISTOR (SOLAR SENSOR))
4.INSPECT COOLER THERMISTOR (SOLAR SENSOR)
a.
E373253C01
1.479,0.104 1.927,0.354 0.448,0.25 1.594,1.344 1,1.854 1,1.854 0.833,1.854 true 1.844,1.344 2.385,1.917 2.385,1.917 2.552,1.917 true 0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 0.552,1.76 0.865,1.958 0.313,0.198 10 false SS- 2.604,1.823 2.917,2.021 0.313,0.198 10 false SS+ 1.563,0.135 1.875,0.333 0.313,0.198 10 false G61
*a Component with harness connected
(Cooler Thermistor (Solar Sensor))


Remove the cooler thermistor (solar sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).


b.

Reconnect the G61 cooler thermistor (solar sensor) connector.


c.

Turn the ignition switch to ON (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G61-1 (SS+) - G61-2 (SS-) Sensor is subjected to electric light 0.8 to 4.3 V
G61-1 (SS+) - G61-2 (SS-) Sensor is covered with a cloth Below 0.8 V


NOTICE:
·

The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 1 and the positive (+) lead to terminal 2 of the cooler thermistor (solar sensor).

·

Do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



HINT:
·

Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the cooler thermistor (solar sensor).

·

As the inspection light is moved away from the sensor, the should decrease.





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE COOLER THERMISTOR (SOLAR SENSOR)

5.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER THERMISTOR (SOLAR SENSOR))
a.

Disconnect the G34 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G61-1 (SS+) - G34-30 (S5-4) Always Below 1 Ω
G61-2 (SS-) - G34-33 (TS) Always Below 1 Ω
G61-1 (SS+) or G34-30 (S5-4) - Body ground Always 10 kΩ or higher
G61-2 (SS-) or G34-33 (TS) - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Disconnect the G90 automatic light control sensor connector.


b.
E222418C13
1.479,0.104 1.938,0.385 0.458,0.281 1.021,1.198 1.51,1.198 false 1.948,1.417 2.427,1.688 false 0.167,0.115 0.448,0.333 0.281,0.219 10 false *a 0.594,1.125 1.313,1.302 0.719,0.177 10 false CLTB 2.479,1.677 3.146,1.885 0.667,0.208 10 false CLTE 1.573,0.156 1.948,0.333 0.375,0.177 10 false G90
*a Front view of wire harness connector
(to Automatic Light Control Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G90-3 (CLTB) - G90-5 (CLTE) Ignition switch off Below 1 V
Ignition switch ON (IG) 11 to 14 V




OK

7.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
7.CHECK HARNESS AND CONNECTOR (AUTOMATIC LIGHT CONTROL SENSOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the G34 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G90-1 (TSD) - G34-33 (TS) Always Below 1 Ω
G90-1 (TSD) or G34-33 (TS) - Body ground Always 10 kΩ or higher




OK

8.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.

Connect the G90 automatic light control sensor connector.


b.
E222419C09
0.646,0.469 1.104,0.75 0.458,0.281 1.542,1.219 0.938,1.385 false 1.906,0.875 2.469,0.75 false 0.146,0.115 0.438,0.375 0.292,0.26 10 false *a 2.521,0.656 2.948,0.875 0.427,0.219 10 false TSD 0.51,1.323 0.969,1.51 0.458,0.188 10 false CLTE 0.74,0.542 1.135,0.75 0.396,0.208 10 false G90
*a Component with harness connected
(Automatic Light Control Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G90-1 (TSD) - G90-5 (CLTE) Sensor is subjected to electric light 0.8 to 4.3 V
Sensor is covered with a cloth Below 0.8 V


NOTICE:
·

The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 1 and the positive (+) lead to terminal 2 of the automatic light control sensor.

·

Do not bring the positive and negative tester probes too close to each other as a short circuit may occur.



HINT:
·

Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the automatic light control sensor.

·

As the inspection light is moved away from the sensor, the should decrease.





OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR

9.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the G59 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G59-22 (CLTE) - G90-5 (CLTE) Always Below 1 Ω
G59-20 (CLTB) - G90-3 (CLTB) Always Below 1 Ω
G59-22 (CLTE) or G90-5 (CLTE) - Body ground Always 10 kΩ or higher
G59-20 (CLTB) or G90-3 (CLTB) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU(MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR