Home › Engine / Hybrid System › 1NZ-FXE (ENGINE MECHANICAL) › ENGINE UNIT › from 2017.06
RM2170E _51 Engine / Hybrid System _057005 1NZ-FXE ENGINE MECHANICAL _0277949 ENGINE UNIT A

1NZ-FXE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 12101 1.INSTALL OIL PAN SUB-ASSEMBLY

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
U159008E02
0.531,0.917 0.208,0.917 0.208,0.917 0.208,2.083 false 0.531,1.969 0.208,1.969 false 0.76,1.427 0.76,0.281 0.76,0.281 1.271,0.281 false 0.906,1.24 0.906,0.281 false 0.594,2.188 0.719,2.333 0.125,0.146 10 false A 0.188,2.104 0.313,2.25 0.125,0.146 10 false A 1.771,2.063 1.896,2.208 0.125,0.146 10 false B 1.323,0.229 1.448,0.375 0.125,0.146 10 false B 1.104,2.563 1.271,2.719 0.167,0.156 10 false *a 2.281,2.5 2.448,2.656 0.167,0.156 10 false *d 2.552,2.688 2.719,2.844 0.167,0.156 10 false *f 2.281,3 2.448,3.156 0.167,0.156 10 false *e 1.396,2.74 1.563,2.896 0.167,0.156 10 false *c 1.104,3.01 1.271,3.167 0.167,0.156 10 false *b

Using an E5 "TORX" socket wrench, install the 4 stud bolts.

Text in Illustration
*a 13 mm (0.512 in.)
*b 8 mm (0.315 in.)
*c 22.5 mm (0.886 in.)
*d 16.5 mm (0.650 in.)
*e 9 mm (0.354 in.)
*f 27.5 mm (1.08 in.)

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
A268104E01
2.995,2.236 3.162,2.391 0.167,0.155 10 *a 2.233,3.183 2.400,3.338 0.167,0.155 10 *b 0.813,3.183 0.980,3.338 0.167,0.155 10 *b 0.587,0.04 0.754,0.195 0.167,0.155 10 *c 2.421,0.04 2.588,0.195 0.167,0.155 10 *d

Apply seal packing to the oil pan sub-assembly as shown in the illustration.

Text in Illustration
*a Apply Seal Packing
*b 4 mm (0.157 in.)
*c 11 mm (0.433 in.)
*d 9 mm (0.354 in.)

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:
·

When the contact surfaces are wet, clean the surfaces with non-residue solvent before applying seal packing.

·

Install the oil pan sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not apply engine oil for at least 2 hours after installation.




c.
A088897

Install 2 new O-rings to the cylinder block and temporarily install the oil pan sub-assembly with the 13 bolts.

NOTICE:
·

When the contact surfaces are wet, clean the surfaces with non-residue solvent before applying seal packing.

·

Be careful that the O-ring is not cracked or moved out of place when installing the oil pan sub-assembly.




d.
U159009E02
2.146,0.677 2.271,0.823 0.125,0.146 10 false A 2.688,0.417 2.813,0.563 0.125,0.146 10 false 5 2.76,0.781 2.885,0.927 0.125,0.146 10 false 4 2.833,1.271 2.958,1.417 0.125,0.146 10 false 3 2.958,1.635 3.083,1.781 0.125,0.146 10 false 9 2.823,1.99 2.948,2.135 0.125,0.146 10 false 2 2.708,2.677 2.885,2.823 0.177,0.146 10 false 13 2.615,3.01 2.802,3.229 0.188,0.219 10 false 12 0.927,3.146 1.104,3.292 0.177,0.146 10 false 11 0.656,2.719 0.833,2.865 0.177,0.146 10 false 10 0.635,1.906 0.76,2.052 0.125,0.146 10 false 1 0.646,1.406 0.771,1.552 0.125,0.146 10 false 8 0.708,0.792 0.833,0.938 0.125,0.146 10 false 7 0.813,0.406 0.938,0.552 0.125,0.146 10 false 6 2.135,1 2.26,1.146 0.125,0.146 10 false A 2.146,1.323 2.271,1.469 0.125,0.146 10 false A 2.26,1.635 2.385,1.781 0.125,0.146 10 false A 2.115,1.979 2.24,2.125 0.125,0.146 10 false A 1.313,1.865 1.438,2.01 0.125,0.146 10 false A 1.333,0.698 1.458,0.844 0.125,0.146 10 false B 1.323,1.031 1.448,1.177 0.125,0.146 10 false B 1.323,1.406 1.448,1.552 0.125,0.146 10 false B 1.302,2.396 1.427,2.542 0.125,0.146 10 false B 2.115,2.396 2.24,2.542 0.125,0.146 10 false B 1.5,2.771 1.625,2.917 0.125,0.146 10 false C 2.031,2.781 2.156,2.927 0.125,0.146 10 false C

Using several steps, uniformly tighten the 13 bolts in the sequence shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)

Item Length Of The Bolt From The Seat To The End.
Bolt A 49 mm (1.93 in.)
Bolt B 88 mm (3.46 in.)
Bolt C 143.7 mm (5.66 in.)


Hide 15104 3.INSTALL OIL STRAINER SUB-ASSEMBLY

a.
A084113

Install a new gasket and the oil strainer sub-assembly with the 2 nuts and bolt.

Torque:
13 N*m (132 kgf*cm, 10 ft.*lbf)


Hide 12102A 4.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.
A267007E01
3.174,1.499 3.327,1.648 0.153,0.149 10 *a

Apply seal packing to the No. 2 oil pan sub-assembly as shown in the illustration below.

Text in Illustration
*a Apply Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.5 mm (0.0984 to 0.138 in.)


NOTICE:
·

When the contact surfaces are wet, clean the surfaces with non-residue solvent before applying seal packing.

·

Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

Do not apply engine oil for at least 2 hours after installation.




b.
A265785

Install the No. 2 oil pan sub-assembly with the 9 bolts and 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


c.

Install the oil pan drain plug with a new gasket.

Torque:
38 N*m (382 kgf*cm, 28 ft.*lbf)


Hide 15600A 5.INSTALL OIL FILTER UNION

a.
A269008

Using a 12 mm hexagon socket wrench, install the oil filter union.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 13050 9.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13511 10.INSTALL CAMSHAFT

HINT:

Perform "Inspection After Repairs" after replacing the camshaft.

w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.

Apply a light coat of engine oil to the camshaft and cylinder head sub-assembly journals.


b.
A269919E01
0.576,0.714 0.741,0.879 0.165,0.165 10 *a 1.678,0.805 0.766,0.805 false 1.654,1.299 1.393,1.299 1.393,1.299 1.393,0.805 false

Place the camshaft on the cylinder head sub-assembly with the timing mark on the camshaft timing gear assembly facing upward.

Text in Illustration
*a Timing Mark


c.
U159030E02
1.563,0.615 1.688,0.76 0.125,0.146 10 false 1 2.115,0.615 2.24,0.76 0.125,0.146 10 false 2 1.021,0.615 1.146,0.76 0.125,0.146 10 false 3 2.667,0.615 2.792,0.76 0.125,0.146 10 false 4

Examine the front marks and numbers, and tighten the 4 No. 2 camshaft bearing caps with the 8 bolts in the sequence shown in the illustration.

Torque:
13 N*m (129 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten each bolt uniformly, keeping the camshaft level.



Hide 13523 11.INSTALL CAMSHAFT TIMING GEAR OR SPROCKET

a.

Clamp the No. 2 camshaft in a vise.

NOTICE:

Be careful not to damage the No. 2 camshaft.



b.
A032167

Align the knock pin hole of the camshaft timing gear or sprocket with the knock pin of the No. 2 camshaft, and tighten the camshaft timing gear or sprocket with the bolt.

Torque:
64 N*m (652 kgf*cm, 47 ft.*lbf)


Hide 13512 12.INSTALL NO. 2 CAMSHAFT

HINT:

Perform "Inspection After Repairs" after replacing the No. 2 camshaft.

w/ Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>INITIALIZATION

w/o Canister Pump Module: Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.

Apply a light coat of engine oil to the No. 2 camshaft and cylinder head sub-assembly journals.


b.
A269920E01
0.567,0.659 0.744,0.824 0.178,0.164 10 *a 2.613,1.505 2.790,1.669 0.178,0.164 10 *b 1.819,0.745 0.775,0.745 false 1.328,1.314 1.328,1.596 1.328,1.596 2.599,1.596 false 2.31,1.242 2.31,1.596 false

Place the No. 2 camshaft on the cylinder head with the timing mark on the camshaft timing gear or sprocket facing upward.

Text in Illustration
*a Timing Mark (Rectangle)
*b Mark (Circle)

HINT:

There are 3 marks on the camshaft timing gear or sprocket. Make sure that the timing mark (rectangle) is at the top.



c.
U159029E03
0.896,1.667 1.219,1.979 1.219,1.979 1.406,1.979 false 2.719,0.969 2.719,1.781 false 1.25,0.948 1.25,1.438 1.25,1.438 2.771,1.438 false 1.76,0.948 1.76,1.438 false 2.26,0.948 2.26,1.438 false 0.802,0.115 1.26,0.396 0.458,0.281 10 false 5 3.01,1.167 3.24,1.438 0.229,0.271 10 false 4 1.49,1.167 1.823,1.51 0.333,0.344 10 false 3 2.5,1.167 2.729,1.417 0.229,0.25 10 false 2 1.99,1.167 2.208,1.375 0.219,0.208 10 false 1 1.469,1.896 1.875,2.156 0.406,0.26 10 false *1 2.656,1.823 2.896,2.01 0.24,0.188 10 false *2

Examine the front marks and numbers, and tighten the No. 1 camshaft bearing cap and No. 2 camshaft bearing caps with the 11 bolts in the sequence shown in the illustration.

Text in Illustration
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap

Torque:
No. 2 camshaft bearing cap : 13 N*m (129 kgf*cm, 9 ft.*lbf)
No. 1 camshaft bearing cap : 23 N*m (234 kgf*cm, 17 ft.*lbf)

NOTICE:

Tighten each bolt uniformly, keeping the No. 2 camshaft level.



Hide 13407 17.INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY

a.
A265784

Install the straight pin to the crankshaft.


b.

Align the hole of the crankshaft damper sub-assembly with the straight pin, then install the crankshaft damper sub-assembly.


c.
A267011E01
0.125,0.24 0.421,0.385 0.296,0.145 10 SST 1.009,0.841 1.009,0.326 1.009,0.326 0.489,0.326 false 0.645,0.829 0.645,0.326 false

Using SST, hold the crankshaft damper sub-assembly in place and tighten the bolt.

SST
09213-58012  (91111-50845)
09330-00021  

T = 128 N*m{ 1,305 kgf*cm 94 ft.*lbf }

NOTICE:

When installing SST, be careful that the bolt which holds SST does not interfere with the timing chain cover.



Hide 12315A 18.INSTALL ENGINE MOUNTING BRACKET RH

Hide 16323 19.INSTALL WATER INLET HOUSING

a.

Install a new gasket to the water inlet housing.


b.
U159027E02
2.094,1.344 2.219,1.49 0.125,0.146 10 false 1 1.302,0.094 1.427,0.24 0.125,0.146 10 false 2 2.552,0.896 2.677,1.042 0.125,0.146 10 false 3

Temporarily install the water inlet housing with the bolt and 2 nuts.


c.

Tighten the bolt and 2 nuts in the sequence shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 16100 20.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A267966

Install a new gasket to the engine water pump assembly.

NOTICE:

When the contact surfaces are wet, clean the surfaces with non-residue solvent before applying seal packing.



b.
A267965

Install the engine water pump assembly with the 5 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16031 21.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

a.
A267962

Install a new gasket to the water inlet with thermostat sub-assembly.


b.
A267959

Install the water inlet with thermostat sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23250 24.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23291 25.INSTALL INJECTOR VIBRATION INSULATOR

Hide 23814B 27.INSTALL FUEL DELIVERY PIPE

a.
U159028E02
0.594,0.354 0.719,0.5 0.125,0.146 10 false A 1.292,0.844 1.417,0.99 0.125,0.146 10 false A 3.146,1.302 3.271,1.448 0.125,0.146 10 false B

Install the fuel delivery pipe with the 3 bolts.

Torque:
Bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Bolt B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Be careful not to drop the fuel injectors when installing the fuel delivery pipe.

·

Check that the fuel injectors rotate smoothly after installing the fuel delivery pipe.




Hide 11201 28.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Install a new gasket to the cylinder head cover sub-assembly.


b.
A267067

Apply seal packing to the 2 locations shown in the illustration.

Text in Illustration
V100135

Apply Seal Packing

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
U159004E04
2.271,1.323 2.396,1.469 0.125,0.146 10 false 1 0.51,0.083 0.635,0.229 0.125,0.146 10 false 7 1.188,0.073 1.313,0.219 0.125,0.146 10 false 8 2.188,0.083 2.313,0.229 0.125,0.146 10 false 9 2.948,0.083 3.125,0.229 0.177,0.146 10 false 10 3.198,1.229 3.375,1.375 0.177,0.146 10 false 11 1.208,1.313 1.521,1.563 0.313,0.25 10 false 2 1.958,1.948 2.188,2.156 0.229,0.208 10 false 3 1.229,1.802 1.49,1.99 0.26,0.188 10 false 4 0.25,1.823 0.448,2 0.198,0.177 10 false 5 0.156,0.625 0.281,0.771 0.125,0.146 10 false 6 1.469,1.302 1.833,1.542 0.365,0.24 10 false *1 2.542,1.292 2.844,1.51 0.302,0.219 10 false *1

Temporarily install the cylinder head cover sub-assembly with the 9 bolts, 2 nuts and 2 new seal washers.

Text in Illustration
*1 Seal Washer


d.

Using several steps, uniformly tighten the bolts and nuts in the sequence shown in the illustration.

Torque:
13 N*m (132 kgf*cm, 10 ft.*lbf)


Hide 12204 29.INSTALL VENTILATION VALVE SUB-ASSEMBLY

a.

Apply adhesive to 2 or 3 threads of the ventilation valve sub-assembly.

Adhesive:

Toyota genuine adhesive 1324, three bond 1324 or equivalent



b.
A269007

Using a 19 mm deep socket wrench, install the ventilation valve sub-assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 11452 30.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 12108A 31.INSTALL OIL FILLER CAP GASKET

a.

Install a new oil filler cap gasket to the oil filler cap.


Hide 12108 32.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.
A269005

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.


Hide 83530 33.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

a.

Apply adhesive to 2 or 3 threads of the engine oil pressure switch assembly.

Adhesive:

Toyota genuine adhesive 1344, three bond 1344 or equivalent



b.
A268028

Using a 24 mm deep socket wrench, install the engine oil pressure switch assembly.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not start the engine within 1 hour of installation.



Hide 89422 34.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

a.
A275780

Using a 19 mm union nut wrench, install a new gasket and the engine coolant temperature sensor.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Use the torque value compensation formula to calculate the torque value for use when a torque wrench is combined with a tool such as a union nut wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 89615 35.INSTALL KNOCK CONTROL SENSOR

a.
A268023E01
1.012,1.853 1.165,1.997 0.153,0.144 10 5° 1.259,1.98 1.412,2.124 0.153,0.144 10 5° 1.576,1.91 1.807,2.054 0.231,0.144 10 25°

Install the knock control sensor with the bolt.

Text in Illustration
V100135

Up
V100136

Engine Front

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Make sure that the knock control sensor is as shown in the illustration.



Hide 15100Q 36.INSTALL CRANKSHAFT POSITION SENSOR

a.
A413180C02
1.531,1.948 1.531,1.542 false 1.521,4.052 1.521,3.646 false 2.146,1.938 1.917,1.938 1.917,1.938 1.781,1.344 true 2.438,4.042 2.208,4.042 2.208,4.042 2.073,3.448 true 2.854,1.354 3.094,1.354 false 2.865,3.458 3.104,3.458 false 0.125,0.073 0.5,0.365 0.375,0.292 12 false *A 0.156,2.375 0.521,2.698 0.365,0.323 12 false *B 1.479,1.948 1.792,2.104 0.313,0.156 10 false *a 1.479,4.042 1.792,4.198 0.313,0.156 10 false *a 2.188,1.865 2.344,2.063 0.156,0.198 10 false A 2.479,3.969 2.635,4.167 0.156,0.198 10 false A 3.125,1.281 3.344,1.531 0.219,0.25 10 false *b 3.146,3.385 3.365,3.635 0.219,0.25 10 false *b
*A for Type A
*B for Type B
*a O-ring Groove
*b Crankshaft Position Sensor Tip


Clean the O-ring groove of the crankshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



b.

Apply protective tape around the part (A) shown in the illustration.


c.

Install a new O-ring to the crankshaft position sensor.

NOTICE:

Set the O-ring on the tip of the crankshaft position sensor and roll it into the O-ring groove with bare hands to install it.



d.
A407852C01
0.906,1.344 1.031,1.49 1.031,1.49 1.25,1.49 false 2.219,3.156 2.219,2.865 false 2.521,0.49 2.688,0.26 2.688,0.26 2.896,0.26 false 2.521,1.354 2.688,1.479 2.688,1.479 2.927,1.479 false 2.823,2.875 3.104,2.875 false 1.927,2.26 2.208,2.26 false 2.208,1.49 2.208,1.198 false 0.906,2.99 1.031,3.135 1.031,3.135 1.25,3.135 false 0.865,0.667 1.208,0.51 1.208,0.51 1.406,0.51 true 0.865,2.302 1.208,2.146 1.208,2.146 1.406,2.146 true 1.292,1.417 1.604,1.573 0.313,0.156 10 false *1 2.938,0.177 3.146,0.385 0.208,0.208 10 false *c 0.313,0.333 0.625,0.49 0.313,0.156 10 false *a 0.323,2 0.635,2.156 0.313,0.156 10 false *b 0.583,0.854 0.74,1.052 0.156,0.198 10 true A 1.031,0.854 1.188,1.052 0.156,0.198 10 true A 1.031,2.51 1.188,2.708 0.156,0.198 10 true B 0.604,2.51 0.76,2.708 0.156,0.198 10 true B 2.156,1.51 2.469,1.667 0.313,0.156 10 false *1 2.156,3.177 2.469,3.333 0.313,0.156 10 false *1 2.344,0.094 2.802,0.292 0.458,0.198 10 false A - A 2.354,1.875 2.813,2.073 0.458,0.198 10 false B - B 3.135,2.813 3.344,3.021 0.208,0.208 10 false *c 2.969,1.406 3.177,1.615 0.208,0.208 10 false *c 1.75,2.177 1.958,2.385 0.208,0.208 10 false *c 1.281,3.063 1.594,3.219 0.313,0.156 10 false *1 1.448,0.448 1.656,0.656 0.208,0.208 10 false *c 1.438,2.083 1.646,2.292 0.208,0.208 10 false *c
*1 O-ring
*a OK
*b NG
*c Seam


Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



e.

Remove the protective tape.

NOTICE:

Make sure to remove the protective tape and any tape adhesive residue.



f.

Apply a light coat of engine oil to the O-ring and install it to the crankshaft position sensor.


g.
A269006

Install the crankshaft position sensor with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 11101J 37.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

a.

Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve assembly.


b.
A266998

Install the camshaft timing oil control valve assembly with the bolt.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 11101E 38.INSTALL CAMSHAFT POSITION SENSOR

a.
A412346C01
1.802,0.958 1.927,0.427 1.927,0.427 2.177,0.427 false 1.99,1.219 2.146,1.865 2.146,1.865 2.458,1.865 true 2.667,1.208 2.969,1.208 false 2.219,0.354 2.531,0.51 0.313,0.156 10 false *a 3,1.125 3.313,1.281 0.313,0.156 10 false *b 2.51,1.792 2.823,1.948 0.313,0.156 10 false A
*a O-ring Groove
*b Camshaft Position Sensor Tip


Clean the O-ring groove of the camshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.



b.

Apply protective tape around the part (A) shown in the illustration.


c.

Install a new O-ring to the camshaft position sensor.

NOTICE:

Set the O-ring on the tip of the camshaft position sensor and roll it into the O-ring groove with bare hands to install it.



d.
A407852C01
0.906,1.344 1.031,1.49 1.031,1.49 1.25,1.49 false 2.219,3.156 2.219,2.865 false 2.521,0.49 2.688,0.26 2.688,0.26 2.896,0.26 false 2.521,1.354 2.688,1.479 2.688,1.479 2.927,1.479 false 2.823,2.875 3.104,2.875 false 1.927,2.26 2.208,2.26 false 2.208,1.49 2.208,1.198 false 0.906,2.99 1.031,3.135 1.031,3.135 1.25,3.135 false 0.865,0.667 1.208,0.51 1.208,0.51 1.406,0.51 true 0.865,2.302 1.208,2.146 1.208,2.146 1.406,2.146 true 1.292,1.417 1.604,1.573 0.313,0.156 10 false *1 2.938,0.177 3.146,0.385 0.208,0.208 10 false *c 0.313,0.333 0.625,0.49 0.313,0.156 10 false *a 0.323,2 0.635,2.156 0.313,0.156 10 false *b 0.583,0.854 0.74,1.052 0.156,0.198 10 true A 1.031,0.854 1.188,1.052 0.156,0.198 10 true A 1.031,2.51 1.188,2.708 0.156,0.198 10 true B 0.604,2.51 0.76,2.708 0.156,0.198 10 true B 2.156,1.51 2.469,1.667 0.313,0.156 10 false *1 2.156,3.177 2.469,3.333 0.313,0.156 10 false *1 2.344,0.094 2.802,0.292 0.458,0.198 10 false A - A 2.354,1.875 2.813,2.073 0.458,0.198 10 false B - B 3.135,2.813 3.344,3.021 0.208,0.208 10 false *c 2.969,1.406 3.177,1.615 0.208,0.208 10 false *c 1.75,2.177 1.958,2.385 0.208,0.208 10 false *c 1.281,3.063 1.594,3.219 0.313,0.156 10 false *1 1.448,0.448 1.656,0.656 0.208,0.208 10 false *c 1.438,2.083 1.646,2.292 0.208,0.208 10 false *c
*1 O-ring
*a OK
*b NG
*c Seam


Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



e.

Remove the protective tape.

NOTICE:

Make sure to remove the protective tape and any tape adhesive residue.



f.

Apply a light coat of engine oil to the O-ring on the camshaft position sensor.


g.
A266999

Install the camshaft position sensor with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)