Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › 2017.06–2019.07
RM2170E _59 Vehicle Exterior _057056 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0278228 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  There is No Sound Made  


DESCRIPTION

The vehicle approaching speaker controller receives stop light switch signals from the stop light switch assembly, vehicle speed signals from the combination meter assembly, engine oil pressure switch signals from the engine oil pressure switch assembly and P position switch signals from the lower shift lever assembly, and produces the warning sound from the vehicle approaching speaker assembly.

WIRING DIAGRAM

E342154E03
3.917,2.333 4.302,2.521 0.385,0.188 10 false SFTP 1.427,2.365 1.719,2.552 0.292,0.188 10 false P2 3.917,4.344 4.26,4.531 0.344,0.188 10 false STP 1.469,3.688 2.073,3.875 0.604,0.188 10 false STOP 4.333,2.177 4.719,2.365 0.385,0.188 10 false SPD 5.823,2.219 6.042,2.406 0.219,0.188 10 false +S 5.969,3.667 6.094,3.854 0.125,0.188 10 false - 5.948,3.396 6.073,3.583 0.125,0.188 10 false + 4.323,5.156 4.708,5.344 0.385,0.188 10 false GND 4.698,2.125 4.875,2.292 0.177,0.167 10 false 6 4.708,5.063 4.885,5.229 0.177,0.167 10 false 7 5.781,3.594 5.958,3.76 0.177,0.167 10 false 2 5.771,3.292 5.948,3.458 0.177,0.167 10 false 1 5.563,2.125 5.74,2.292 0.177,0.167 10 false 39 5.25,2.531 5.542,2.698 0.292,0.167 10 false G1 5.25,2.698 7.115,3.052 1.865,0.354 10 false Combination Meter Assembly 0.417,2.74 0.708,2.906 0.292,0.167 10 false G25 0.417,2.896 2.167,3.104 1.75,0.208 10 false Lower Shift Lever Assembly 0.938,4.625 1.229,4.792 0.292,0.167 10 false A65 0.938,4.771 2.698,5.094 1.76,0.323 10 false Stop Light Switch Assembly 5.406,3.958 5.698,4.125 0.292,0.167 10 false A73 5.406,4.125 6.823,4.479 1.417,0.354 10 false Vehicle Approaching Speaker Assembly 3.49,5.615 3.854,5.781 0.365,0.167 10 false G85 3.49,5.781 4.906,6.135 1.417,0.354 10 false Vehicle Approaching Speaker Controller 3.656,2.271 3.833,2.438 0.177,0.167 10 false 11 1.719,2.281 1.865,2.469 0.146,0.188 10 false 2 1.25,4.26 1.448,4.427 0.198,0.167 10 false 1 3.729,4.26 3.927,4.427 0.198,0.167 10 false 2 4.177,0.448 4.698,0.635 0.521,0.188 10 false OPSW 4.698,0.344 4.875,0.51 0.177,0.167 10 false 12 5.646,0.354 5.823,0.521 0.177,0.167 10 false 1 5.427,0.75 5.719,0.917 0.292,0.167 10 false E2 5.427,0.906 6.708,1.604 1.281,0.698 10 false Engine Oil Pressure Switch Assembly 3.927,0.438 4.135,0.625 0.208,0.188 10 false IG 3.729,0.375 3.906,0.542 0.177,0.167 10 false 1 0.323,0.49 1.323,0.844 1,0.354 10 false from IG1 NO. 1 Relay 1.719,0.625 2.281,0.813 0.563,0.188 10 false GAUGE 0.25,1.385 0.448,1.552 0.198,0.167 10 false 3A 0.25,1.531 3.021,1.885 2.771,0.354 10 false Instrument Panel Junction Block Assembly 2.094,5.302 2.979,5.625 0.885,0.323 10 false to Stop Lights 2.635,0.385 2.833,0.552 0.198,0.167 10 false 49 5.823,1.865 5.938,2.052 0.115,0.188 10 false S 5.573,1.802 5.75,1.969 0.177,0.167 10 false 22 4.344,3.354 4.729,3.542 0.385,0.188 10 false SP+ 4.344,3.667 4.729,3.854 0.385,0.188 10 false SP- 4.719,3.292 4.896,3.458 0.177,0.167 10 false 3 4.719,3.594 4.896,3.76 0.177,0.167 10 false 8 2.219,4.271 2.417,4.438 0.198,0.167 10 false 2 2.375,3.563 3.823,3.75 1.448,0.188 10 false from Auxiliary Battery 1.438,4.354 1.635,4.521 0.198,0.167 10 false B 2.031,4.375 2.365,4.542 0.333,0.167 10 false L

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Trouble Codes.


e.

Check for DTCs.

Result:
Result Proceed to
DTC B1350 is not output A
DTC B1350 is output B
Communication with the GTS is not possible C




A

2.PERFORM ACTIVE TEST USING GTS (Proximity Sound (Vehicle Stationary))

B

C

GO TO DIAGNOSTIC PROCEDURE (Communication between Vehicle Proximity Notification System and Diagnostic Tool is not Possible)

2.PERFORM ACTIVE TEST USING GTS (Proximity Sound (Vehicle Stationary))
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Test Part Control Range Diagnostic Note
Proximity Sound (Vehicle Stationary) Proximity sound (Vehicle stationary) OFF or ON Produces warning sound when vehicle is stopped

Result:
Result Proceed to
The warning sound is produced A
The warning sound is not produced B




A

3.READ VALUE USING GTS (Stop Light SW)

B

10.INSPECT VEHICLE APPROACHING SPEAKER ASSEMBLY
3.READ VALUE USING GTS (Stop Light SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
-

Result:
Result Proceed to
The GTS display changes according to brake pedal operation A
The GTS display does not change according to brake pedal operation B




A

4.READ VALUE USING GTS (Vehicle Speed)

B

12.CHECK STOP LIGHT OPERATION
4.READ VALUE USING GTS (Vehicle Speed)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) Almost the same as actual vehicle speed -

Result:
Result Proceed to
The GTS display changes according to the vehicle speed A
The GTS display does not change according to the vehicle speed B




A

5.READ VALUE USING GTS (Oil Pressure SW)

B

14.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - COMBINATION METER ASSEMBLY)
5.READ VALUE USING GTS (Oil Pressure SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Oil Pressure SW Oil pressure switch / OFF or ON OFF: Engine started
ON: Engine not started
-

Result:
Result Proceed to
The GTS display changes according to engine operation A
The GTS display does not change according to engine operation B




A

6.READ VALUE USING GTS (Shift Position)

B

16.CHECK ENGINE OIL PRESSURE SWITCH ASSEMBLY (INPUT SIGNAL)
6.READ VALUE USING GTS (Shift Position)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Vehicle Proximity Notification System / Data List.


e.

Read the Data List according to the display on the GTS.

Vehicle Proximity Notification System
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift Position P position switch / Not Parking or Parking Not Parking or Parking -

Result:
Result Proceed to
The GTS display changes according to the selected shift state A
The GTS display does not change according to the selected shift state B




A

B

7.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (SHIFT)
7.CHECK VEHICLE APPROACHING SPEAKER CONTROLLER (SHIFT)
a.

Disconnect the G25 lower shift lever assembly connector.


b.
U159740E01
1.348,0.291 1.630,0.473 0.281,0.181 10 G25 0.094,0.085 0.264,0.260 0.170,0.174 10 *a 0.909,0.667 1.453,1.235 false 0.656,0.49 0.913,0.665 0.257,0.174 10 P2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G25-2 (P2) - Body ground Power switch on (IG) 8 V or higher
Power switch off Below 1 V



Text in Illustration
*a Front view of wire harness connector
(to Lower Shift Lever Assembly)


OK

8.CHECK LOWER SHIFT LEVER ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - LOWER SHIFT LEVER ASSEMBLY)
8.CHECK LOWER SHIFT LEVER ASSEMBLY
a.

Reconnect the G25 lower shift lever assembly connector.


b.
U159746E02
2.271,0.385 1.844,0.99 false 0.729,1.01 1.521,1.417 0.792,0.406 10 false G25 0.135,0.094 0.49,0.365 0.354,0.271 10 false *a 2.313,0.208 2.708,0.448 0.396,0.24 10 false P2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G25-2 (P2) - Body ground Power switch on (IG), park (P) selected 8 V or higher
Power switch on (IG), park (P) not selected Below 2.5 V



Text in Illustration
*a Component with harness connected
(Lower Shift Lever Assembly)


OK

NG

REPLACE LOWER SHIFT LEVER ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - LOWER SHIFT LEVER ASSEMBLY)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Disconnect the G25 lower shift lever assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-11 (SFTP) - G25-2 (P2) Always Below 1 Ω
G85-11 (SFTP) or G25-2 (P2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT VEHICLE APPROACHING SPEAKER ASSEMBLY
a.

Remove the vehicle approaching speaker assembly (see page Vehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER>REMOVAL).


b.

Inspect the vehicle approaching speaker assembly (see page Vehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE APPROACHING SPEAKER>INSPECTION).



OK

11.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - VEHICLE APPROACHING SPEAKER ASSEMBLY)

NG

11.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - VEHICLE APPROACHING SPEAKER ASSEMBLY)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Disconnect the A64 vehicle approaching speaker assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-3 (SP+) - A64-1 (+) Always Below 1 Ω
G85-8 (SP-) - A64-2 (-) Always Below 1 Ω
G85-3 (SP+) or A64-1 (+) - Body ground Always 10 kΩ or higher
G85-8 (SP-) or A64-2 (-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed On
Brake pedal released Off




OK

13.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - STOP LIGHT SWITCH ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Disconnect the A65 stop light switch assembly connector.


c.

Disconnect the M5 rear combination light assembly LH connector.


d.

Disconnect the M6 rear combination light assembly RH connector.


e.

Disconnect the S2 center stop light set connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-2 (STP) - A65-2 (L) Always Below 1 Ω
G85-2 (STP) or A65-2 (L) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - COMBINATION METER ASSEMBLY)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Disconnect the G1 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-6 (SPD) - G1-39 (+S) Always Below 1 Ω
G85-6 (SPD) or G1-39 (+S) - Body ground Always 10 kΩ or higher




OK

15.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK COMBINATION METER ASSEMBLY
a.

Reconnect the G85 vehicle approaching speaker controller connector.


b.

Reconnect the G1 combination meter assembly connector.


c.
U159164E03
0.698,1.854 0.875,1.417 false 1.135,3.896 1.385,3.896 false 1.073,3.708 1.073,4.031 false 1.448,3.708 1.448,4.031 false 0.135,0.115 0.292,0.271 0.156,0.156 10 false *a 0.583,1.885 0.771,2.042 0.188,0.156 10 false +S 2.781,3.635 3.104,3.792 0.323,0.156 10 false GND 1.198,3.927 1.313,4.083 0.115,0.156 10 false A 1.625,0.458 1.927,0.615 0.302,0.156 10 false G1

Check the input waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal G1-39 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Power switch on (IG), wheel being rotated

Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

NG

16.CHECK ENGINE OIL PRESSURE SWITCH ASSEMBLY (INPUT SIGNAL)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.
U183752E02
2.146,1.417 2.51,1.688 false 1.594,0.25 1.927,0.417 0.333,0.167 10 false G85 2.396,1.698 2.948,1.865 0.552,0.167 10 false OPSW 0.094,0.094 0.427,0.26 0.333,0.167 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G85-12 (OPSW) - Body ground Idling* 8 V or higher
Power switch on (IG) Below 2 V


HINT:

*:Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).



Text in Illustration
*a Front view of wire harness connector
(to Vehicle Approaching Speaker Controller)


OK

NG

17.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OIL PRESSURE SWITCH ASSEMBLY)
17.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - ENGINE OIL PRESSURE SWITCH ASSEMBLY)
a.

Disconnect the G85 vehicle approaching speaker controller connector.


b.

Disconnect the E2 engine oil pressure switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G85-12 (OPSW) - E2-1 Always Below 1 Ω
G85-12 (OPSW) or E2-1 - Body ground Always 10 kΩ or higher




OK

REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR