Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2018.08
RM2170E _57 Power Source / Network _057033 NETWORKING _0278068 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0129  Lost Communication with Brake System Control Module  U0293  Lost Communication with HV ECU  


DESCRIPTION

·

The hybrid vehicle control computer assembly communicates with the ECM and brake booster with master cylinder assembly (skid control ECU). When the hybrid vehicle control computer assembly does not receive data from the ECM or brake booster with master cylinder assembly (skid control ECU), the hybrid vehicle control computer assembly stores DTC U0100 or U0129.

·

The ECM communicates with the hybrid vehicle control computer assembly. When the ECM does not receive data from the hybrid vehicle control computer assembly, the ECM stores DTC U0293.

·

The brake booster with master cylinder assembly (skid control ECU) communicates with the hybrid vehicle control computer assembly. When the brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control computer assembly, the brake booster with master cylinder assembly (skid control ECU) stores DTC U0293.


DTC No. DTC Detection Condition Trouble Area
U0100 The hybrid vehicle control computer assembly does not receive data from the ECM.
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of hybrid vehicle control computer assembly

·

Hybrid vehicle control computer assembly

·

Power source circuit of ECM

·

ECM

·

Open or short in CAN junction connector LH


U0129 The hybrid vehicle control computer assembly does not receive data from the brake booster with master cylinder assembly (skid control ECU).
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of hybrid vehicle control computer assembly

·

Hybrid vehicle control computer assembly

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Open or short in CAN junction connector LH


U0293
·

The ECM does not receive data from the hybrid vehicle control computer assembly.

·

The brake booster with master cylinder assembly (skid control ECU) does not receive data from the hybrid vehicle control computer assembly.


·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of ECM

·

ECM

·

Power source circuit of hybrid vehicle control computer assembly

·

Hybrid vehicle control computer assembly

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Open or short in CAN junction connector LH



HINT:

This diagnosis procedure is for when DTC U0100, U0129 and U0293 are output at the same time.


WIRING DIAGRAM

C251628E17
1.094,0.948 1.438,1.229 0.344,0.281 10 false G81 1.406,0.948 2.583,1.573 1.177,0.625 10 false Hybrid Vehicle Control Computer Assembly 0.865,3.99 2.854,4.323 1.99,0.333 10 false CAN Junction Connector LH 2.021,6.781 2.406,7.115 0.385,0.333 10 false ECM 1.698,6.781 1.979,7.115 0.281,0.333 10 false A40 5.26,4.542 6.99,5.052 1.729,0.51 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 4.927,4.542 5.219,4.906 0.292,0.365 10 false A41 3.323,0.781 3.833,0.969 0.51,0.188 10 false 120 Ω 3.302,7.042 3.813,7.229 0.51,0.188 10 false 120 Ω 2.688,1.365 3.115,1.542 0.427,0.177 10 false CA3N 4,1.365 4.427,1.542 0.427,0.177 10 false CA3P 5.865,3.479 6.292,3.656 0.427,0.177 10 false CA2H 5.865,4.115 6.292,4.292 0.427,0.177 10 false CA2L 2.677,6.448 3.104,6.625 0.427,0.177 10 false CANN 3.969,6.448 4.396,6.625 0.427,0.177 10 false CANP 2.927,1.646 3.156,1.875 0.229,0.229 10 false 30 3.979,1.646 4.208,1.875 0.229,0.229 10 false 31 2.917,6.167 3.146,6.396 0.229,0.229 10 false 25 3.969,6.167 4.198,6.396 0.229,0.229 10 false 12 2.75,3.031 2.99,3.271 0.24,0.24 10 false 16 4.156,3.021 4.385,3.25 0.229,0.229 10 false 5 2.885,2.26 3.115,2.49 0.229,0.229 10 false W 4.042,2.26 4.271,2.49 0.229,0.229 10 false R 5.188,3.396 5.417,3.625 0.229,0.229 10 false L 5.167,4.188 5.396,4.417 0.229,0.229 10 false W 2.885,5.677 3.115,5.906 0.229,0.229 10 false W 4.042,5.677 4.271,5.906 0.229,0.229 10 false B 4.344,3.427 4.573,3.656 0.229,0.229 10 false 5 4.313,4.219 4.542,4.448 0.229,0.229 10 false 16 5.625,3.469 5.854,3.698 0.229,0.229 10 false 35 5.625,4.115 5.854,4.344 0.229,0.229 10 false 34 2.76,4.979 2.99,5.208 0.229,0.229 10 false 18 4.135,4.979 4.365,5.208 0.229,0.229 10 false 7 0.938,8 2.844,8.177 1.906,0.177 10 false : CAN Main Bus Line (CANH) 0.938,8.406 2.844,8.583 1.906,0.177 10 false : CAN Main Bus Line (CANL) 3.885,8 5.792,8.177 1.906,0.177 10 false : CAN Branch Line (CANH) 3.885,8.417 5.792,8.594 1.906,0.177 10 false : CAN Branch Line (CANL) 0.146,0.115 1.833,0.615 1.688,0.5 12 false Sub Bus 15: 4.26,3.625 4.552,3.99 0.292,0.365 10 false A74 4.271,3.99 4.563,4.354 0.292,0.365 10 false A74 3.792,4.958 4.083,5.323 0.292,0.365 10 false A74 3.021,4.958 3.313,5.323 0.292,0.365 10 false A74 3.01,3.031 3.302,3.396 0.292,0.365 10 false G86 3.76,3.031 4.052,3.396 0.292,0.365 10 false G86 5.49,0.771 6.927,1.115 1.438,0.344 10 false x: Suspected Area

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If the hybrid vehicle control computer assembly outputs only DTC U0129, troubleshoot DTC U0129 and check the branch circuit of sub bus 15.


Result:
Result Proceed to
The hybrid vehicle control computer assembly outputs DTC U0129 and other DTCs.
(GTS display: Hybrid Control)
A
The hybrid vehicle control computer assembly outputs only DTC U0129.
(GTS display: Hybrid Control)
B




A

2.CHECK SUB BUS 15

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK SUB BUS 15
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U183644E02
2.698,1.115 2.594,0.563 2.594,0.563 2.521,0.563 false 1.823,1.104 1.677,0.531 1.677,0.531 1.458,0.531 false 2.427,1.313 2.271,1.823 2.271,1.823 2.063,1.823 false 2.469,1.313 2.625,1.823 2.625,1.823 2.833,1.823 false 1.927,0.25 2.365,0.51 0.438,0.26 10 false G80 2.51,0.25 2.948,0.51 0.438,0.26 10 false G81 2.146,0.479 2.646,0.698 0.5,0.219 10 false BATT 1.24,0.438 1.5,0.646 0.26,0.208 10 false E1 1.667,1.729 2.167,1.948 0.5,0.219 10 false CA3P 2.875,1.729 3.333,1.948 0.458,0.219 10 false CA3N 0.073,0.052 0.375,0.313 0.302,0.26 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
G81-31 (CA3P) - G81-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
G81-31 (CA3P) - G80-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
G81-30 (CA3N) - G80-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
G81-31 (CA3P) - G81-3 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
G81-30 (CA3N) - G81-3 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control Computer Assembly)

HINT:
·

When the values are as specified, clear and recheck for DTCs. When no DTCs are output, check for malfunctions such as damage or improper connection of the relevant connectors.

·

If DTCs are output although the bus circuit is normal and DTCs were cleared, replace the hybrid vehicle control computer assembly.



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D




A

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY

B

3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY)

C

7.CHECK FOR SHORT IN SUB BUS 15 LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)

D

12.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN J/C LH)
3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY)
a.
U183186E02
1.708,2.781 2.427,2.583 false 1.75,3.052 2.469,2.573 false 2.531,3.021 2.927,3.219 0.396,0.198 10 false G81 1.281,2.708 1.667,2.885 0.385,0.177 10 false CA3P 1.333,2.99 1.719,3.167 0.385,0.177 10 false CA3N 0.167,0.094 0.49,0.375 0.323,0.281 10 false *a

Disconnect the G81 hybrid vehicle control computer assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-31 (CA3P) - G81-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly)



OK

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY

NG

4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)
4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)
a.

Reconnect the G81 hybrid vehicle control computer assembly connector.


b.
U183529E03
1.615,1.365 1.615,0.531 1.615,0.531 1.448,0.531 false 1.625,1.563 1.625,1.896 1.625,1.896 1.458,1.896 false 0.104,0.135 0.719,0.542 0.615,0.406 10 false *a 0.542,1.229 0.969,1.5 0.427,0.271 10 false G86 0.875,0.458 1.458,0.688 0.583,0.229 10 false CANH*b 0.917,1.823 1.49,2.042 0.573,0.219 10 false CANL*b

Disconnect the G86 CAN junction connector LH (instrument panel wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G86-5 (CANH) - G86-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Hybrid vehicle control computer assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Hybrid Vehicle Control Computer Assembly



OK

5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)

5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN J/C LH)
a.

Reconnect the G86 CAN junction connector LH (instrument panel wire side).


b.
U183530E03
1.844,1.365 1.844,0.531 1.844,0.531 2.01,0.531 false 1.844,1.563 1.844,1.896 1.844,1.896 2.01,1.896 false 0.104,0.083 0.719,0.49 0.615,0.406 10 false *a 0.542,1.219 0.969,1.49 0.427,0.271 10 false A74 2.073,0.458 2.656,0.688 0.583,0.229 10 false CANH*b 2.073,1.823 2.646,2.042 0.573,0.219 10 false CANL*b

Disconnect the A74 CAN junction connector LH (engine room main wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A74-7 (CANH) - A74-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to ECM



OK

REPLACE CAN JUNCTION CONNECTOR LH

NG

6.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN J/C LH)
6.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN J/C LH)
a.

Reconnect the A74 CAN junction connector LH (engine room main wire side).


b.
U159409E03
2.5,1.625 2.865,1.625 2.865,1.625 2.865,2.406 false 2.49,1.531 2.49,0.938 2.49,0.938 2.729,0.938 false 0.156,0.125 0.396,0.365 0.24,0.24 10 false *a 2.802,0.854 3.24,1.052 0.438,0.198 10 false CANP 2.677,2.448 3.146,2.646 0.469,0.198 10 false CANN 1.781,0.708 2.063,0.885 0.281,0.177 10 false A40

Disconnect the A40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-12 (CANP) - A40-25 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - CAN J/C LH)

7.CHECK FOR SHORT IN SUB BUS 15 LINES (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)
a.
U183186E02
1.708,2.781 2.427,2.583 false 1.75,3.052 2.469,2.573 false 2.531,3.021 2.927,3.219 0.396,0.198 10 false G81 1.281,2.708 1.667,2.885 0.385,0.177 10 false CA3P 1.333,2.99 1.719,3.167 0.385,0.177 10 false CA3N 0.167,0.094 0.49,0.375 0.323,0.281 10 false *a

Disconnect the G81 hybrid vehicle control computer assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-31 (CA3P) - G81-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly)



OK

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY

NG

8.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
8.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
a.

Reconnect the G81 hybrid vehicle control computer assembly connector.


b.
U183529E03
1.615,1.365 1.615,0.531 1.615,0.531 1.448,0.531 false 1.625,1.563 1.625,1.896 1.625,1.896 1.458,1.896 false 0.104,0.135 0.719,0.542 0.615,0.406 10 false *a 0.542,1.229 0.969,1.5 0.427,0.271 10 false G86 0.875,0.458 1.458,0.688 0.583,0.229 10 false CANH*b 0.917,1.823 1.49,2.042 0.573,0.219 10 false CANL*b

Disconnect the G86 CAN junction connector LH (instrument panel wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G86-5 (CANH) - G86-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Hybrid vehicle control computer assembly


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Hybrid Vehicle Control Computer Assembly



OK

9.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)

9.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN J/C LH)
a.

Reconnect the G86 CAN junction connector LH (instrument panel wire side).


b.
C354333E06
0.417,1.167 0.833,1.417 0.417,0.25 1.594,1.375 1.594,0.542 1.594,0.542 1.427,0.542 false 1.833,1.365 1.833,0.531 1.833,0.531 2,0.531 false 1.438,1.896 1.604,1.896 1.604,1.896 1.604,1.563 false 2,1.896 1.833,1.896 1.833,1.896 1.833,1.563 false 0.083,0.125 0.49,0.385 0.406,0.26 10 false *a 0.865,0.469 1.49,0.771 0.625,0.302 10 false CANH*b 0.896,1.813 1.521,2.073 0.625,0.26 10 false CANL*b 0.5,1.208 0.906,1.469 0.406,0.26 10 false A74 2.083,0.458 2.708,0.76 0.625,0.302 10 false CANH*c 2.073,1.813 2.698,2.073 0.625,0.26 10 false CANL*c

Disconnect the A74 CAN junction connector LH (engine room main wire side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A74-5 (CANH) - A74-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)
A74-7 (CANH) - A74-18 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM


Text in Illustration
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
*c to ECM

Result:
Result Proceed to
OK A
NG (ECM CAN main bus lines) B
NG (Brake booster with master cylinder assembly (Skid control ECU) CAN branch lines) C




A

REPLACE CAN JUNCTION CONNECTOR LH

B

10.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN J/C LH)

C

11.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)
10.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN J/C LH)
a.

Reconnect the A74 CAN junction connector LH (engine room main wire side).


b.
U159409E03
2.5,1.625 2.865,1.625 2.865,1.625 2.865,2.406 false 2.49,1.531 2.49,0.938 2.49,0.938 2.729,0.938 false 0.156,0.125 0.396,0.365 0.24,0.24 10 false *a 2.802,0.854 3.24,1.052 0.438,0.198 10 false CANP 2.677,2.448 3.146,2.646 0.469,0.198 10 false CANN 1.781,0.708 2.063,0.885 0.281,0.177 10 false A40

Disconnect the A40 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-12 (CANP) - A40-25 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - CAN J/C LH)

11.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)
a.

Reconnect the A74 CAN junction connector LH (engine room main wire side).


b.
U159481E02
1.656,2.135 1.656,2.708 1.656,2.708 1.427,2.708 false 1.76,2.135 1.76,2.708 1.76,2.708 1.979,2.708 false 0.198,0.167 0.406,0.323 0.208,0.156 10 false *a 1.625,0.875 1.917,1.031 0.292,0.156 10 false A41 2.031,2.625 2.51,2.802 0.479,0.177 10 false CA2H 1.031,2.615 1.51,2.792 0.479,0.177 10 false CA2L

Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-35 (CA2H) - A41-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (for LHD)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (for RHD)

C

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)

12.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN J/C LH)
a.
C405263C01
0.396,1.417 0.823,1.667 0.427,0.25 0.031,3.5 0.448,3.729 0.417,0.229 0.031,3.219 0.448,3.448 0.417,0.229 1.656,1.542 1.656,0.708 1.656,0.708 1.49,0.708 true 1.656,1.729 1.656,2.146 1.656,2.146 1.49,2.146 true 1.719,3.135 1.719,2.635 1.719,2.635 1.427,2.635 true 2.521,3.719 2.521,4.052 true 0.479,1.458 0.833,1.688 0.354,0.229 10 false G86 0.135,3.521 0.49,3.75 0.354,0.229 10 false G4 0.052,0.063 0.563,0.396 0.51,0.333 10 false *a 2.375,4.083 2.729,4.292 0.354,0.208 10 false BAT 1.135,2.552 1.427,2.771 0.292,0.219 10 false CG 0.938,0.625 1.521,0.844 0.583,0.219 10 false CANH*b 0.958,2.063 1.542,2.281 0.583,0.219 10 false CANL*b 0.052,2.229 0.563,2.563 0.51,0.333 10 false *1 0.083,3.25 0.438,3.479 0.354,0.229 10 false G93 0.469,3.229 0.823,3.458 0.354,0.229 12 false *A 0.469,3.51 0.823,3.74 0.354,0.229 12 false *B
*A for LHD
*B for RHD
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Instrument Panel Wire Side))
*b to Hybrid Vehicle Control Computer Assembly


Disconnect the G86 CAN junction connector LH (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition Connected to
G86-5 (CANH) - G93-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control computer assembly
G86-16 (CANL) - G93-4 (CG)
G86-5 (CANH) - G93-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Hybrid vehicle control computer assembly
G86-16 (CANL) - G93-16 (BAT)

for RHD
Tester Connection Condition Specified Condition Connected to
G86-5 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Hybrid vehicle control computer assembly
G86-16 (CANL) - G4-4 (CG)
G86-5 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Hybrid vehicle control computer assembly
G86-16 (CANL) - G4-16 (BAT)


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.





OK

13.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN J/C LH)

NG

14.CHECK FOR SHORT IN SUB BUS 15 LINE (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)
13.CHECK FOR SHORT IN SUB BUS 15 LINE (CAN J/C LH)
a.

Disconnect the A74 CAN junction connector LH (engine room main wire side).


b.
C405263C02
0.396,1.417 0.823,1.667 0.427,0.25 0.031,3.5 0.448,3.729 0.417,0.229 0.031,3.219 0.448,3.448 0.417,0.229 1.656,1.542 1.656,0.708 1.656,0.708 1.49,0.708 true 1.656,1.729 1.656,2.146 1.656,2.146 1.49,2.146 true 1.719,3.135 1.719,2.635 1.719,2.635 1.427,2.635 true 2.521,3.719 2.521,4.052 true 1.896,1.531 1.896,0.698 1.896,0.698 2.063,0.698 true 1.906,1.74 1.906,2.156 1.906,2.156 2.073,2.156 true 0.479,1.458 0.833,1.688 0.354,0.229 10 false A74 0.135,3.521 0.49,3.75 0.354,0.229 10 false G4 0.052,0.063 0.563,0.396 0.51,0.333 10 false *a 2.375,4.083 2.729,4.292 0.354,0.208 10 false BAT 1.135,2.552 1.427,2.771 0.292,0.219 10 false CG 0.938,0.625 1.521,0.844 0.583,0.219 10 false CANH*b 0.958,2.063 1.542,2.281 0.583,0.219 10 false CANL*b 0.052,2.229 0.563,2.563 0.51,0.333 10 false *1 0.083,3.25 0.438,3.479 0.354,0.229 10 false G93 0.469,3.229 0.823,3.458 0.354,0.229 12 false *A 0.469,3.51 0.823,3.74 0.354,0.229 12 false *B 2.146,0.615 2.729,0.833 0.583,0.219 10 false CANH*c 2.135,2.063 2.719,2.281 0.583,0.219 10 false CANL*c
*A for LHD
*B for RHD
*1 DLC3
*a Front view of wire harness connector
(to CAN Junction Connector LH (Engine Room Main Wire Side))
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
*c to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition Connected to
A74-5 (CANH) - G93-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)
A74-16 (CANL) - G93-4 (CG)
A74-7 (CANH) - G93-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
A74-18 (CANL) - G93-4 (CG)
A74-5 (CANH) - G93-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Brake booster with master cylinder assembly (Skid control ECU)
A74-16 (CANL) - G93-16 (BAT)
A74-7 (CANH) - G93-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A74-18 (CANL) - G93-16 (BAT)

for LHD
Tester Connection Condition Specified Condition Connected to
A74-5 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (Skid control ECU)
A74-16 (CANL) - G4-4 (CG)
A74-7 (CANH) - G4-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
A74-18 (CANL) - G4-4 (CG)
A74-5 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Brake booster with master cylinder assembly (Skid control ECU)
A74-16 (CANL) - G4-16 (BAT)
A74-7 (CANH) - G4-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A74-18 (CANL) - G4-16 (BAT)


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.



Result:
Result Proceed to
OK A
NG (ECM CAN main bus line) B
NG (Brake booster with master cylinder assembly (Skid control ECU) CAN branch line) C




A

REPLACE CAN JUNCTION CONNECTOR LH

B

15.CHECK FOR SHORT IN SUB BUS 15 LINE (ECM - CAN J/C LH)

C

16.CHECK FOR SHORT IN SUB BUS 15 LINE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)
14.CHECK FOR SHORT IN SUB BUS 15 LINE (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)
a.
U183516E02
1.781,2.375 1.104,2.604 false 2.469,2.573 2.927,2.688 false 2.417,2.573 2.917,2.938 false 2.708,2.365 2.708,1.896 2.708,1.896 2.625,1.896 false 1.865,2.99 2.146,3.146 0.281,0.156 10 false G80 0.885,2.563 1.073,2.74 0.188,0.177 10 false E1 2.219,1.802 2.792,1.979 0.573,0.177 10 false BATT 2.979,2.896 3.354,3.073 0.375,0.177 10 false CA3P 2.958,2.615 3.344,2.792 0.385,0.177 10 false CA3N 0.156,0.135 0.594,0.469 0.438,0.333 10 false *a 2.531,3 2.813,3.156 0.281,0.156 10 false G81

Disconnect the G80 and G81 hybrid vehicle control computer assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G81-31 (CA3P) - G80-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
G81-30 (CA3N) - G80-6 (E1)
G81-31 (CA3P) - G81-3 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
G81-30 (CA3N) - G81-3 (BATT)


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.



Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control Computer Assembly)



OK

REPLACE HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (HYBRID VEHICLE CONTROL COMPUTER ASSEMBLY - CAN J/C LH)

15.CHECK FOR SHORT IN SUB BUS 15 LINE (ECM - CAN J/C LH)
a.
U183640E01
0.114,0.114 0.561,0.445 0.447,0.331 10 *a 2.69,0.517 3.191,0.707 0.501,0.190 10 CANP 2.69,2.072 3.153,2.262 0.463,0.190 10 CANN 0.475,0.517 0.976,0.707 0.501,0.190 10 BATT 0.727,2.896 1.011,3.085 0.284,0.190 10 E1 1.727,0.528 2.076,0.718 0.349,0.190 10 A40 2.43,2.963 2.746,3.153 0.316,0.190 10 C10 1.648,3.639 1.252,2.985 1.252,2.985 0.94,2.985 false 1.425,1.267 1.262,0.604 1.262,0.604 0.935,0.604 false 2.429,1.267 2.429,0.595 2.429,0.595 2.667,0.595 false 2.425,1.342 2.425,2.169 2.425,2.169 2.653,2.169 false 2.075,2.963 2.365,3.181 0.290,0.218 10 *A 1.662,2.963 1.979,3.153 0.316,0.190 10 C9 2.928,2.963 3.218,3.181 0.290,0.218 10 *B

Disconnect the A40 and C9 or C10 ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A40-12 (CANP) - C9-16 (E1)*1
A40-12 (CANP) - C10-16 (E1)*2
Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A40-25 (CANN) - C9-16 (E1)*1
A40-25 (CANN) - C10-16 (E1)*2
A40-12 (CANP) - A40-1 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A40-25 (CANN) - A40-1 (BATT)


*1: for RHD

*2: for LHD

HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.



Text in Illustration
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CAN J/C LH)

16.CHECK FOR SHORT IN SUB BUS 15 LINE (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)
a.
U183566E02
1.667,2.146 1.667,2.719 1.667,2.719 1.438,2.719 false 1.771,2.146 1.771,2.719 1.771,2.719 1.99,2.719 false 2.458,1.667 2.458,0.865 2.458,0.865 2.615,0.865 false 2.646,2.031 2.813,2.594 false 0.198,0.167 0.406,0.323 0.208,0.156 10 false *a 1.625,0.865 1.917,1.021 0.292,0.156 10 false A41 2.042,2.625 2.521,2.802 0.479,0.177 10 false CA2H 1.042,2.625 1.521,2.802 0.479,0.177 10 false CA2L 2.615,2.625 3,2.802 0.385,0.177 10 false GND 2.667,0.781 2.917,0.969 0.25,0.188 10 false BI

Disconnect the A41 brake booster with master cylinder assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A41-35 (CA2H) - A41-28 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A41-34 (CA2L) - A41-28 (GND)
A41-35 (CA2H) - A41-14 (BI) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A41-34 (CA2L) - A41-14 (BI)


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 15 inspection.



Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (for LHD)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) (for RHD)

C

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU) - CAN J/C LH)