Home › Engine / Hybrid System › 1NZ-FXE (ENGINE CONTROL) › SFI SYSTEM(w/ Canister Pump Module) › from 2018.08
RM2170E _51 Engine / Hybrid System _057003 1NZ-FXE ENGINE CONTROL _0320444 SFI SYSTEM(w/ Canister Pump Module) C

1NZ-FXE ENGINE CONTROL  SFI SYSTEM(w/ Canister Pump Module)  P0462  Fuel Level Sensor "A" Circuit Low  P0463  Fuel Level Sensor "A" Circuit High  


DESCRIPTION

Refer to DTC P0461.

Click hereEngine / Hybrid System>1NZ-FXE (ENGINE CONTROL)>SFI SYSTEM(w/ Canister Pump Module)>P0461

DTC No. DTC Detection Condition Trouble Area
P0462 Fuel sender gauge output resistance is below 7 Ω for 30 seconds or more (1 trip detection logic).
·

Open or short in fuel sender gauge circuit

·

Fuel sender gauge assembly

·

Combination meter assembly

·

ECM


P0463 Fuel sender gauge output resistance is higher than 480 Ω for 30 seconds or more (2 trip detection logic).
·

Open or short in fuel sender gauge circuit

·

Fuel sender gauge assembly

·

Combination meter assembly

·

ECM



MONITOR DESCRIPTION

The combination meter assembly sends fuel level sensor signals to the ECM via CAN communication.

When the power switch is on (IG), if the output resistance of the fuel level sensor is less than 7 Ω or higher than 480 Ω for 30 seconds or more, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel level sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the power switch off and wait for at least 30 seconds.

6.

Turn the power switch on (IG).

7.

Turn the GTS on.

8.

Wait 30 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0462 or P0463.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A431940E01
0.958,3.25 4.625,3.448 3.667,0.198 10 false : CAN Communication Line 0.24,2.656 0.656,2.927 0.417,0.271 10 false M22 0.24,2.823 3.469,3.094 3.229,0.271 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.354,1.188 0.51,1.385 0.156,0.198 10 false A 0.333,1.354 2.938,1.552 2.604,0.198 10 false Fuel Sender Gauge 1.75,1.01 1.906,1.208 0.156,0.198 10 false 1 2.115,0.552 2.427,0.75 0.313,0.198 10 false FS 3.563,0.667 3.719,0.865 0.156,0.198 10 false L 3.396,0.563 3.552,0.76 0.156,0.198 10 false 2 1.75,1.698 1.906,1.896 0.156,0.198 10 false 2 2.135,1.896 2.448,2.094 0.313,0.198 10 false FE 2.396,1.906 2.552,2.104 0.156,0.198 10 false 3 2.375,0.542 2.531,0.74 0.156,0.198 10 false 2 3.448,2.625 3.76,2.823 0.313,0.198 10 false G1 3.458,2.802 5.469,3.198 2.01,0.396 10 false Combination Meter Assembly 4.135,1.583 4.75,1.781 0.615,0.198 10 false CANL 4.594,1.396 4.906,1.594 0.313,0.198 10 false 32 4.115,0.885 4.729,1.083 0.615,0.198 10 false CANH 4.594,0.688 4.906,0.885 0.313,0.198 10 false 31 5.792,0.885 6.406,1.083 0.615,0.198 10 false CANH 5.542,0.698 5.854,0.896 0.313,0.198 10 false 13 5.542,1.396 5.854,1.594 0.313,0.198 10 false 26 5.802,1.604 6.417,1.802 0.615,0.198 10 false CANL 5.74,2.688 6.198,2.885 0.458,0.198 10 false A40 6.073,2.688 6.552,3.021 0.479,0.333 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the fuel suction tube with pump and gauge assembly connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M22-2 (FS) - G1-2 (L) Always Below 1 Ω
M22-3 (FE) - Body ground Always Below 1 Ω
M22-2 (FS) or G1-2 (L) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT FUEL SENDER GAGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FUEL SENDER GAGE ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

3.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
E391971C12
0.458,1.281 0.865,1.521 0.406,0.24 0.323,3.635 0.729,3.875 0.406,0.24 1.719,1.219 1.719,0.677 false 1.396,1.208 1.115,0.802 false 0.531,1.323 0.99,1.521 0.458,0.198 10 false M22 0.479,3.667 0.938,3.865 0.458,0.198 10 false A 0.115,0.083 0.573,0.281 0.458,0.198 10 false *a 1.01,0.625 1.469,0.823 0.458,0.198 10 false FE 1.615,0.49 2.073,0.688 0.458,0.198 10 false FS
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


a.

Disconnect the fuel suction tube with pump and gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M22-3 (FE) - A-2 Always Below 1 Ω
M22-2 (FS) - A-1 Always Below 1 Ω
M22-3 (FE) - M22-2 (FS) or A-2 - A-1 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY