Home › Vehicle Exterior › DOOR / HATCH › HOOD LOCK CONTROL CABLE ASSEMBLY › 2018.08–2019.07
RM2170E _59 Vehicle Exterior _057046 DOOR / HATCH _0278159 HOOD LOCK CONTROL CABLE ASSEMBLY A

DOOR / HATCH  HOOD LOCK CONTROL CABLE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 76902 1.REMOVE SIDE MUDGUARD SUB-ASSEMBLY LH (for LHD)

Hide 2.REMOVE FRONT WHEEL LH (for LHD)

Hide 53876A 3.REMOVE FRONT FENDER LINER LH (for LHD)

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Exterior>WIPER / WASHER>WASHER MOTOR(for Front Side)>REMOVAL


Hide 67914 4.REMOVE FRONT DOOR SCUFF PLATE LH (for LHD)

Hide 62112 5.REMOVE COWL SIDE TRIM BOARD LH (for LHD)

Hide 6.REMOVE FRONT WHEEL RH (for RHD)

Hide 53875A 7.REMOVE FRONT FENDER LINER RH (for RHD)

Hide 67913 8.REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111C 9.REMOVE COWL SIDE TRIM BOARD RH (for RHD)

HINT:

Use the same procedure for the RH side and LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 53601 10.REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B284569

Disengage the 3 claws and disconnect the hood lock control lever sub-assembly.


b.

for Type A:

i.
B533667

Disconnect the hood lock control cable assembly to remove the hood lock control lever sub-assembly.

HINT:

When changing the hood lock control lever sub-assembly from type A to type B, the hood lock control cable assembly must also be changed to type B.




c.

for Type B:

i.
B533668

Disconnect the hood lock control cable assembly to remove the hood lock control lever sub-assembly.

HINT:

When changing the hood lock control lever sub-assembly from type B to type A, the hood lock control cable assembly must also be changed to type A.




Hide 53510 11.REMOVE HOOD LOCK ASSEMBLY

a.
B477869

Remove the 3 bolts.


b.
B477870

Disconnect the hood lock control cable assembly and remove the hood lock assembly.


Hide 53630 12.REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)

a.

Using a screwdriver, disengage the hood lock control cable assembly from the 3 clamps and hood cable grommet as shown in the illustration.

B477871C02
2.75,0.625 3.167,0.458 false 3.167,1.146 3.083,0.896 false 4.563,1.115 4.729,1.115 false 4.531,1.313 4.188,1.135 true 6.281,3.635 6.615,3.833 true 6.219,4.094 6.417,3.906 false 6.208,2.25 6.375,2.25 true 5.771,2.542 5.979,2.271 true 3.125,1.177 3.438,1.333 0.313,0.156 10 false *1 4.76,1.031 5.073,1.188 0.313,0.156 10 false *a 3.208,0.365 3.521,0.521 0.313,0.156 10 false *b 4.604,1.25 4.917,1.406 0.313,0.156 10 false *1 6.094,3.542 6.365,3.698 0.271,0.156 10 false *1 5.667,2.563 5.938,2.719 0.271,0.156 10 false *1 6.104,4.094 6.417,4.25 0.313,0.156 10 false *a 6.417,2.167 6.729,2.323 0.313,0.156 10 false *a
*1 Hood Lock Control Cable Assembly - -
*a Clamp *b Hood Cable Grommet


HINT:

Tape the screwdriver tip before use.



b.

Pull the hood lock control cable assembly from the engine compartment and remove it.

HINT:
B533666C01
0.167,0.167 0.5,0.417 0.333,0.25 12 false *A 0.167,1.75 0.5,2 0.333,0.25 12 false *B
*A Type A
*B Type B


·

When changing the hood lock control cable assembly from type A to type B, the hood lock control lever sub-assembly must also be changed to type B.

·

When changing the hood lock control cable assembly from type B to type A, the hood lock control lever sub-assembly must also be changed to type A.




Hide 53630 13.REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)

a.

Using a screwdriver, disengage the hood lock control cable assembly from the 3 clamps and hood cable grommet as shown in the illustration.

B477872C01
6.115,0.802 6.49,0.667 false 6.573,1.365 6.448,1.052 false 6,3.917 6.25,3.917 false 0.927,3.781 1.26,3.781 false 1.417,1.427 1.25,1.177 false 0.552,1.115 0.802,1.115 true 1.417,4.094 1.563,3.781 true 6.667,4.167 6.5,3.917 true 0.333,1.031 0.646,1.188 0.313,0.156 10 false *1 1.385,1.438 1.698,1.594 0.313,0.156 10 false *a 6.552,0.563 6.865,0.719 0.313,0.156 10 false *b 6.531,1.396 6.844,1.552 0.313,0.156 10 false *1 6.625,4.188 6.938,4.344 0.313,0.156 10 false *1 1.323,4.125 1.635,4.281 0.313,0.156 10 false *1 0.708,3.688 1.021,3.844 0.313,0.156 10 false *a 5.802,3.833 6.115,3.99 0.313,0.156 10 false *a
*1 Hood Lock Control Cable Assembly - -
*a Clamp *b Hood Cable Grommet


HINT:

Tape the screwdriver tip before use.



b.

Pull the hood lock control cable assembly from the engine compartment and remove it.

HINT:
B533666C01
0.167,0.167 0.5,0.417 0.333,0.25 12 false *A 0.167,1.75 0.5,2 0.333,0.25 12 false *B
*A Type A
*B Type B


·

When changing the hood lock control cable assembly from type A to type B, the hood lock control lever sub-assembly must also be changed to type B.

·

When changing the hood lock control cable assembly from type B to type A, the hood lock control lever sub-assembly must also be changed to type A.