Home › Engine / Hybrid System › 2ZR-FXE (ENGINE CONTROL) › SFI SYSTEM › 2013.08–2014.11
RM2070E _51 Engine / Hybrid System _061905 2ZR-FXE ENGINE CONTROL _0301559 SFI SYSTEM C

2ZR-FXE ENGINE CONTROL  SFI SYSTEM  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No. DTC Detection Condition Trouble Area
P0300 Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic).
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter sub-assembly

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

EGR valve assembly

·

ECM


P0301
P0302
P0303
P0304
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic).
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks when detect immediately).

·

An emission deterioration misfire occurs (MIL illuminates).



When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when the following condition, which could cause emission deterioration, is detected (2 trip detection logic).

·

An excessive number of misfires (approximately 50 to 80 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.

·

At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.

·

At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature sensor
Intake air temperature sensor
Mass air flow meter sub-assembly
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Misfire
Intake air temperature Higher than -10°C (14°F)
Either of the following conditions is met A or B
A. Engine coolant temperature at engine start Higher than -7°C (19°F)
B. Engine coolant temperature Higher than 20°C (68°F)

Monitor Period of Emission-related Misfire
Duration Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Duration Crankshaft 200 revolutions x 3

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).

3.

Turn the GTS on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Using the GTS, switch the ECM from normal mode to check mode (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE).

8.

Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

9.

Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

HINT:

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.

Engine speed Duration
Idling 4.5 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


10.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the power switch off until the output DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data are cleared.


11.

Record the DTC(s), freeze frame data and misfire counts.

12.

Turn the power switch off and wait for at least 30 seconds.

13.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).


WIRING DIAGRAM

Refer to Fuel Injector Circuit (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>Fuel Injector Circuit).

Mass air flow meter sub-assembly circuit: Refer to DTC P0102 (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>P0102).

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:

(a)

There was insufficient fuel in the tank.

(b)

Improper fuel is used.

(c)

The spark plugs have been contaminated.

(d)

The problem requires further diagnosis.


·

After finishing repairs, check the misfire counts of the cylinders Cylinder #1 Misfire Count to Cylinder #4 Misfire Count.

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.

·

When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (20% or higher).

·

When the Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfire has occurred only while warming up the engine.

·

An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Result
Result Proceed to
DTC P0300, P0301, P0302, P0303 and/or P0304 are output A
DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output B

HINT:

If any DTCs other than P0300, P0301, P0302, P0303 and/or P0304 are output, troubleshoot those DTCs first.




A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

OK:

PCV valve and hose are correctly connected and are not damaged.



OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

REPAIR OR REPLACE PCV HOSE

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.


e.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.




NEXT

4.READ VALUE USING GTS (CYLINDER #1 (TO #4) MISFIRE COUNT)
4.READ VALUE USING GTS (CYLINDER #1 (TO #4) MISFIRE COUNT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 (to #4) Misfire Count.


f.

Start the engine and allow the engine to idle.


g.

Read each value for Cylinder #1 (to #4) Misfire Count displayed on the GTS. If no misfire counts occur in any cylinders, perform steps [A] and [B], and then check the misfire counts again.


h.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the read value using the GTS (Misfire RPM and Misfire Load) procedures above [A].


i.

Read Cylinder #1 (to #4) Misfire Count or the DTCs displayed on the GTS [B].

Result
Misfire Count Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B

HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data record of the engine coolant temperature is less than 75°C (167°F), it may only be possible to detect the misfire when the engine is cold.





A

5.INSPECT SPARK PLUG

B

18.CHECK INTAKE SYSTEM
5.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).



OK

6.CHECK FOR SPARK (SPARK TEST)

NG

6.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

If the result of the spark test is normal, proceed to the next step.




NEXT

7.CHECK CYLINDER COMPRESSION PRESSURE
7.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).



OK

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.
U190510E02
2.417,2.354 2.99,2.719 true 2.313,2.333 2.49,2.927 true 2.24,2.354 2.052,2.958 true 2.531,2.51 2.969,3 true 2.115,2.333 1.604,2.885 true 0.333,0.156 0.521,0.333 0.188,0.177 10 false *a 0.198,2.896 0.49,3.104 0.292,0.208 10 false D28 1.479,2.927 1.75,3.073 0.271,0.146 10 false #40 1.917,2.979 2.188,3.125 0.271,0.146 10 false #30 2.417,2.969 2.688,3.115 0.271,0.146 10 false #20 3.052,2.656 3.323,2.802 0.271,0.146 10 false #10 3,2.969 3.271,3.115 0.271,0.146 10 false E01

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D28-85 (#10) - D28-109 (E01) Power switch on (IG) 11 to 14 V
D28-84 (#20) - D28-109 (E01) Power switch on (IG) 11 to 14 V
D28-83 (#30) - D28-109 (E01) Power switch on (IG) 11 to 14 V
D28-82 (#40) - D28-109 (E01) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

9.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

9.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL INJECTOR>INSPECTION).



OK

10.CHECK INTAKE SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

10.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in intake system.




OK

11.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

11.CHECK FUEL PRESSURE

OK

12.READ VALUE USING GTS (COOLANT TEMP)

NG

36.CHECK FUEL LINE
12.READ VALUE USING GTS (COOLANT TEMP)

OK

13.READ VALUE USING GTS (MAF)

NG

13.READ VALUE USING GTS (MAF)

OK

14.ADJUST VALVE TIMING

NG

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
14.ADJUST VALVE TIMING

NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (P0300, P0301, P0302, P0303 OR P0304)
15.CHECK WHETHER DTC OUTPUT RECURS (P0300, P0301, P0302, P0303 OR P0304)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


m.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output)
A
NORMAL
(DTC is not output)
B



A

16.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

B

END

16.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.


g.

Check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result
Result Proceed to
NG A
OK B



A

17.INSPECT EGR VALVE ASSEMBLY

B

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
17.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.


Result
Result Proceed to
NG A
OK B



A

B

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
18.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>2ZR-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in intake system.




OK

19.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

19.CHECK FUEL PRESSURE

OK

20.READ VALUE USING GTS (COOLANT TEMP)

NG

36.CHECK FUEL LINE
20.READ VALUE USING GTS (COOLANT TEMP)

OK

21.READ VALUE USING GTS (MAF)

NG

21.READ VALUE USING GTS (MAF)

OK

22.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
22.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


e.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

The A/C switch and all accessory switches should be off.



f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / All Data / MAP.


g.

Check the MAP value in the Data List while performing the Active Test.

HINT:
·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

MAP change in response to EGR step position.


Standard:
- EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
MAP
(Data List)
(EGR valve is fully closed) MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed


HINT:
·

While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



Result
Result Proceed to
NG A
OK B



A

23.INSPECT EGR VALVE ASSEMBLY

B

24.INSPECT SPARK PLUG
23.INSPECT EGR VALVE ASSEMBLY
a.

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.




OK

24.INSPECT SPARK PLUG

NG

24.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).



OK

25.CHECK FOR SPARK (SPARK TEST)

NG

25.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION).

HINT:

If the result of the spark test is normal, proceed to the next step.




NEXT

26.CHECK CYLINDER COMPRESSION PRESSURE
26.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).



OK

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

27.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.
U190510E02
2.417,2.354 2.99,2.719 true 2.313,2.333 2.49,2.927 true 2.24,2.354 2.052,2.958 true 2.531,2.51 2.969,3 true 2.115,2.333 1.604,2.885 true 0.333,0.156 0.521,0.333 0.188,0.177 10 false *a 0.198,2.896 0.49,3.104 0.292,0.208 10 false D28 1.479,2.927 1.75,3.073 0.271,0.146 10 false #40 1.917,2.979 2.188,3.125 0.271,0.146 10 false #30 2.417,2.969 2.688,3.115 0.271,0.146 10 false #20 3.052,2.656 3.323,2.802 0.271,0.146 10 false #10 3,2.969 3.271,3.115 0.271,0.146 10 false E01

Disconnect the ECM connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D28-85 (#10) - D28-109 (E01) Power switch on (IG) 11 to 14 V
D28-84 (#20) - D28-109 (E01) Power switch on (IG) 11 to 14 V
D28-83 (#30) - D28-109 (E01) Power switch on (IG) 11 to 14 V
D28-82 (#40) - D28-109 (E01) Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

28.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

28.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL INJECTOR>INSPECTION).



OK

29.ADJUST VALVE TIMING

NG

REPLACE FUEL INJECTOR ASSEMBLY

29.ADJUST VALVE TIMING

NEXT

30.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304)
30.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


m.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output)
A
NORMAL
(DTC is not output)
B



A

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)

B

END

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

32.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
32.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


m.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output)
A
NORMAL
(DTC is not output)
B



A

33.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

B

END

33.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

OK

34.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
a.

Replace the mass air flow meter sub-assembly (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).

HINT:

If the results of the inspections performed in steps 13 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.




NEXT

35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.



e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the GTS on.


h.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.


l.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


m.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 and/or P0304 is output)
B



A

END

B

36.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.



OK

NG

REPAIR OR REPLACE FUEL LINE