The camshaft position sensor for the intake camshaft (G2 signal) consists of a magnet and MRE (Magneto Resistance Element).
The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration and injection timing.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0340 | When either of following conditions is met (1 trip detection logic):
·
No camshaft position sensor signal to ECM at engine speed 600 rpm or higher ·
Missing camshaft position sensor signal despite crankshaft position sensor inputs normal at engine speed of 600 rpm or higher |
·
Open or short in camshaft position sensor circuit ·
Camshaft position sensor ·
Intake camshaft ·
Valve timing ·
ECM |
| P0342 | Output voltage of camshaft position sensor less than 0.3 V (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit ·
Camshaft position sensor ·
ECM |
| P0343 | Output voltage of camshaft position sensor higher than 4.7 V (1 trip detection logic). | ·
Open or short in camshaft position sensor circuit ·
Camshaft position sensor ·
ECM |
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
| ECM Terminal Name | Between G2+ and G2- |
| Tester Range | 5 V/DIV., 20 ms./DIV. |
| Condition | Idling with warm engine |
If no signal is transmitted by the camshaft position sensor despite the engine revolving, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.
| Required Sensors/Components (Main) | Camshaft position sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the power switch on (IG) and turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine.
Idle the engine for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0340, P0342 or P0343.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
Disconnect the camshaft position sensor connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D18-3 (VC) - Body ground | Power switch on (IG) | 4.5 to 5.0 V |
| *a | Front view of wire harness connector
(to Camshaft Position Sensor) |
OK
NG
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D18-1 (VVI+) - D28-76 (G2+) | Always | Below 1 Ω |
| D18-2 (VVI-) - D28-122 (G2-) | Always | Below 1 Ω |
| D18-1 (VVI+) or D28-76 (G2+) - Body ground | Always | 10 kΩ or higher |
| D18-2 (VVI-) or D28-122 (G2-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the camshaft position sensor installation.
Camshaft position sensor is installed correctly.
OK
NG
Check the timing rotor of the intake camshaft.
Timing rotor does not have any cracks or deformation.
OK
NG
Replace the camshaft position sensor (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL).
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0340, P0342 or P0343 is output | A |
| DTC is not output | B |
A
B
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0340, P0342 or P0343 is output | B |
If the engine does not start, replace the ECM.
A
B
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D18-3 (VC) - D28-99 (VCV1) | Always | Below 1 Ω |
| D18-3 (VC) or D28-99 (VCV1) - Body ground | Always | 10 kΩ or higher |
OK
NG