For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).
If the generator inverter overheats, has a circuit malfunction, or has an internal short, the inverter transmits this information to the MG ECU via the generator inverter fail signal line.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0A7A | 122 | Generator inverter fail signal detection (overcurrent due to system malfunction) | ·
Power management control ECU ·
Inverter with converter assembly ·
Hybrid vehicle generator assembly ·
Hybrid vehicle motor assembly ·
Generator cable ·
Motor cable ·
Wire harness or connector ·
PCU fuse |
Refer to the wiring diagram for DTC P0A1A-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200).
Refer to the wiring diagram for DTC P324E-788 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P324E-788).
Refer to the wiring diagram for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the power switch on (READY) and wait for 5 seconds or more.
Drive the vehicle for approximately 10 minutes mainly using the engine.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P0A7A-122 is set before any of the DTCs in the table below are set | A |
| Any of the DTCs including pending DTCs in the table 1 below are set before P0A7A-122 is set | B |
| Any of the DTCs in the table 2 below are set before P0A7A-122 is set | C |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0AC0-817 | Hybrid Battery Pack Current Sensor Circuit Range / Performance |
| P3004-131 | High Voltage Power Resource |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A7F-123 | Hybrid Battery Pack Deterioration |
| P0A80-123 | Replace Hybrid Battery Pack |
| P0A9C-123 | Hybrid Battery Temperature Sensor "A" Range / Performance |
| P0A9D-123 | Hybrid Battery Temperature Sensor "A" Circuit Low |
| P0A9E-123 | Hybrid Battery Temperature Sensor "A" Circuit High |
| P0ABF-123 | Hybrid Battery Pack Current Sensor Circuit |
| P0AC0-123 | Hybrid Battery Pack Current Sensor Circuit Range/Performance |
| P0AC1-123 | Hybrid Battery Pack Current Sensor Circuit Low |
| P0AC2-123 | Hybrid Battery Pack Current Sensor Circuit High |
| P0AC6-123 | Hybrid Battery Temperature Sensor "B" Range/Performance |
| P0AC7-123 | Hybrid Battery Temperature Sensor "B" Circuit Low |
| P0AC8-123 | Hybrid Battery Temperature Sensor "B" Circuit High |
| P0ACB-123 | Hybrid Battery Temperature Sensor "C" Range / Performance |
| P0ACC-123 | Hybrid Battery Temperature Sensor "C" Circuit Low |
| P0ACD-123 | Hybrid Battery Temperature Sensor "C" Circuit High |
| P0AE9-123 | Hybrid Battery Temperature Sensor "D" Range / Performance |
| P0AEA-123 | Hybrid Battery Temperature Sensor "D" Circuit Low |
| P0AEB-123 | Hybrid Battery Temperature Sensor "D" Circuit High |
| P0AFC-123 | Hybrid Battery Pack Sensor Module |
| P0B10-123 | Hybrid Battery Pack Current Sensor "B" Circuit Low |
| P0B11-123 | Hybrid Battery Pack Current Sensor "B" Circuit High |
| P0B13-123 | Hybrid Battery Pack Current Sensor "A"/"B" Correlation |
| P0BC3-123 | Hybrid Battery Temperature Sensor "E" Range / Performance |
| P0BC4-123 | Hybrid Battery Temperature Sensor "E" Circuit Low |
| P0BC5-123 | Hybrid Battery Temperature Sensor "E" Circuit High |
| P0C34-123 | Hybrid Battery Temperature Sensor "F" Range / Performance |
| P0C35-123 | Hybrid Battery Temperature Sensor "F" Circuit Low |
| P0C36-123 | Hybrid Battery Temperature Sensor "F" Circuit High |
| P3011-123 | Battery Block 1 Becomes Weak |
| P3012-123 | Battery Block 2 Becomes Weak |
| P3013-123 | Battery Block 3 Becomes Weak |
| P3014-123 | Battery Block 4 Becomes Weak |
| P3015-123 | Battery Block 5 Becomes Weak |
| P3016-123 | Battery Block 6 Becomes Weak |
| P3017-123 | Battery Block 7 Becomes Weak |
| P3018-123 | Battery Block 8 Becomes Weak |
| P301A-123 | Open in Hybrid Battery Cell Voltage Detection Circuit |
| P301B-123 | Hybrid Battery Cell Voltage Detection Circuit Range/Performance |
| P3065-123 | Hybrid Battery Temperature Sensor Range/Performance Stuck "A" |
| P306A-123 | Hybrid Battery Temperature Sensor Range / Performance Stuck "B" |
| P31AA-123 | Hybrid Battery Cell High Voltage |
| P31AB-123 | Hybrid Battery Cell Low Voltage |
| P31AC-123 | Hybrid Battery Cell Extreme High Voltage |
| P31B3-123 | Hybrid Battery Voltage High |
| U029A-123 | Lost Communication with Hybrid Battery Pack Sensor Module |
Refer to the freeze frame data to determine the order in which the DTCs were set.
P0A7A-122 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.
Turn the power switch off.
A
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
C
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P0A7A-203 is not output | A |
| P0A7A-203 is also output | B |
If P0A7A-203 is output, troubleshoot it first. After completing the troubleshooting for P0A7A-203, return to perform troubleshooting for this DTC.
Parts repaired or replaced during troubleshooting for P0A7A-203 do not need to be re-inspected in this diagnosis procedure.
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
If P0A7A-203 was not output in step 2 of this diagnosis procedure, check reference 1 below.
If P0A7A-203 was output in step 2 of this diagnosis procedure, repair that DTC first, then check reference 2 below.
| Result | Proceed to |
|---|---|
| Only P0A7A-122 is output, or DTCs other than the ones in the table below are also output. | A |
| Any of the following DTCs including pending DTCs in the table 1 and 3 below are also output. | B |
| Any of the following DTCs in the table 2 and 4 below are also output. | C |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A1A (all INF codes)*1 | Generator Control Module |
| P0A1B (all INF codes)*1 | Drive Motor "A" Control Module |
| P0A1D (all INF codes)*1 | Hybrid Powertrain Control Module |
| P0A3F-243 | Drive Motor "A" Position Sensor Circuit |
| P0A40-500 | Drive Motor "A" Position Sensor Circuit Range/Performance |
| P0A41-245 | Drive Motor "A" Position Sensor Circuit Low |
| P0A4B-253 | Generator Position Sensor Circuit |
| P0A4C-513 | Generator Position Sensor Circuit Range/Performance |
| P0A4D-255 | Generator Position Sensor Circuit Low |
| P0A60 (all INF codes)*1 | Drive Motor "A" Phase V Current |
| P0A63 (all INF codes)*1 | Drive Motor "A" Phase W Current |
| P0A72 (all INF codes)*1 | Generator Phase V Current |
| P0A75 (all INF codes)*1 | Generator Phase W Current |
| P0A78-266, 267, 279, 287, 306, 503, 504, 505, 506, 586, 806, 807, 808 | Drive Motor "A" Inverter Performance |
| P0A7A-325, 344, 517, 518, 809, 810, 811 | Generator Inverter Performance |
| P0A90-509 | Drive Motor "A" Performance |
| P0A92-521 | Hybrid Generator Performance |
| P0A94-442, 547, 548, 549, 554, 555, 556, 585, 587, 589, 590 | DC/DC Converter Performance |
| P0ADB-227 | Hybrid Battery Positive Contactor Control Circuit Low |
| P0ADC-226 | Hybrid Battery Positive Contactor Control Circuit High |
| P0ADF-229 | Hybrid Battery Negative Contactor Control Circuit Low |
| P0AE0-228 | Hybrid Battery Negative Contactor Control Circuit High |
| P0C76-523 | Hybrid Battery System Discharge Time Too Long |
| P3000-388, 389, 603 | Battery Control System |
| P3004-133, 803 | High Voltage Power Resource |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A95-123 | High Voltage Fuse |
| P31B4-123 | Extreme Charging Current Caused by Hybrid Battery High Voltage |
| P31B5-123 | Abnormal Current Caused by Continuous Current from Hybrid Battery |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A1A (all INF codes)*1 | Generator Control Module |
| P0A1B (all INF codes)*1 | Drive Motor "A" Control Module |
| P0A1D (all INF codes)*1 | Hybrid Powertrain Control Module |
| P0A3F-243 | Drive Motor "A" Position Sensor Circuit |
| P0A40-500 | Drive Motor "A" Position Sensor Circuit Range/Performance |
| P0A41-245 | Drive Motor "A" Position Sensor Circuit Low |
| P0A4B-253 | Generator Position Sensor Circuit |
| P0A4C-513 | Generator Position Sensor Circuit Range/Performance |
| P0A4D-255 | Generator Position Sensor Circuit Low |
| P0A60 (all INF codes)*1 | Drive Motor "A" Phase V Current |
| P0A63 (all INF codes)*1 | Drive Motor "A" Phase W Current |
| P0A72-333 | Generator Phase V Current |
| P0A75-341 | Generator Phase W Current |
| P0A78-266, 267, 279, 287, 306, 503, 504, 505, 506, 586, 806, 807, 808 | Drive Motor "A" Inverter Performance |
| P0A7A-325, 517, 518, 809, 810, 811 | Generator Inverter Performance |
| P0A90-509 | Drive Motor "A" Performance |
| P0A94-442, 547, 548, 549, 554, 555, 556, 585, 587, 589, 590 | DC/DC Converter Performance |
| P0ADB-227 | Hybrid Battery Positive Contactor Control Circuit Low |
| P0ADC-226 | Hybrid Battery Positive Contactor Control Circuit High |
| P0ADF-229 | Hybrid Battery Negative Contactor Control Circuit Low |
| P0AE0-228 | Hybrid Battery Negative Contactor Control Circuit High |
| P0C76-523 | Hybrid Battery System Discharge Time Too Long |
| P3000-388, 389, 603 | Battery Control System |
| P3004-133, 803 | High Voltage Power Resource |
| DTC No. | Relevant Diagnosis |
|---|---|
| P0A95-123 | High Voltage Fuse |
| P31B4-123 | Extreme Charging Current Caused by Hybrid Battery High Voltage |
| P31B5-123 | Abnormal Current Caused by Continuous Current from Hybrid Battery |
*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.
P0A7A-122 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.
Turn the power switch off.
A
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
C
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID BATTERY SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
A
B
C
A
B
C
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
OK
NG
Refer to replace inverter with converter assembly parts (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).
NEXT
NEXT
A
B
C
OK
NG
A
B
C
OK
NG