Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.10–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A94-172  DC / DC Converter Performance  


DESCRIPTION

For a description of the boost converter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A94-442).

If a malfunction occurs in the boost converter, the MG ECU detects it and transmits this information to the power management control ECU.

DTC No. INF Code DTC Detection Condition Trouble Area
P0A94 172 Boost converter fail signal detection (overcurrent by system malfunction)
·

Wire harness or connector

·

Hybrid vehicle transaxle assembly

·

Generator cable

·

Motor cable

·

Inverter with converter assembly

·

PCU fuse

·

Power management control ECU

·

Hybrid battery junction block assembly

·

Service plug grip



WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A1A-200 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A1A-200).

Refer to the wiring diagram for DTC P324E-788 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P324E-788).

Refer to the wiring diagram for DTC U0110-159 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>U0110-159).

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 5 seconds or more.

2.

With the engine stopped and park (P) selected, depress the accelerator pedal to start the engine.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0A95-123 is not output. A
P0A95-123 is also output. B


NOTICE:
·

If P0A95-123 is output, troubleshoot it first. After completing the troubleshooting for P0A95-123, return to perform troubleshooting for this DTC.

·

Parts repaired or replaced during troubleshooting for P0A95-123 do not need to be re-inspected in this diagnosis procedure.




e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P0A94-172 only is output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A (all INF codes)*1 Generator Control Module
P0A1B (all INF codes)*1 Drive Motor "A" Control Module
P0A1D (all INF codes)*1 Hybrid Powertrain Control Module
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A40-500 Drive Motor "A" Position Sensor Circuit Range / Performance
P0A41-245 Drive Motor "A" Position Sensor Circuit Low
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range / Performance
P0A4D-255 Generator Position Sensor Circuit Low
P0A60 (all INF codes)*1 Drive Motor "A" Phase V Current
P0A63 (all INF codes)*1 Drive Motor "A" Phase W Current
P0A72 (all INF codes)*1 Generator Phase V Current
P0A75 (all INF codes)*1 Generator Phase W Current
P0A78-113, 128, 266, 267, 279, 284, 286, 287, 306, 503, 504, 505, 506, 586, 806, 807, 808 Drive Motor "A" Inverter Performance
P0A7A-122, 130, 322, 324, 325, 344, 517, 518, 809, 810, 811 Generator Inverter Performance
P0A90-509 Drive Motor "A" Performance
P0A92-521 Hybrid Generator Performance
P0A94-442, 547, 548, 549, 554, 555, 556, 585, 587, 589, 590 DC / DC Converter Performance
P0AA6-526 Hybrid Battery Voltage System Isolation Fault
P0C76-523 Hybrid Battery System Discharge Time Too Long

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0A94-172 may be set due to a malfunction which also causes DTCs in the preceding table to be set. In this case, first troubleshoot the output DTCs in the preceding table. Then, perform a test to attempt to reproduce the problems, and check that no DTCs are output.




e.

Turn the power switch off.



A

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

3.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

4.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

OK

5.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK GENERATOR RESOLVER

OK

6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

20.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
6.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

OK

7.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK MOTOR RESOLVER

OK

8.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

NG

22.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
8.CHECK INVERTER WITH CONVERTER ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

A

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

9.CHECK INVERTER WITH CONVERTER ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

10.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

NG

24.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)
11.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG2)

OK

12.CHECK FUSE (PCU)

NG

26.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)
12.CHECK FUSE (PCU)

OK

13.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

NG

28.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)
13.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY POWER SOURCE CIRCUIT)

OK

14.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

14.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

OK

15.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK POWER MANAGEMENT CONTROL ECU

OK

16.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

16.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

17.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

17.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

18.CLEAR DTC

NG

CONNECT SECURELY

18.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

19.CHECK DTC OUTPUT (HYBRID CONTROL)
19.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and wait for 5 seconds or more.


c.

Turn the power switch on (READY) and wait for 5 seconds or more.


d.

Depress the accelerator pedal with the engine stopped and park (P) selected to start the engine and idle it for 10 seconds or more.


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output. A
DTC P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 is output. A
DTCs other than P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 are output. B



g.

Turn the power switch off.



A

REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT, HYBRID BATTERY JUNCTION BLOCK ASSEMBLY AND SERVICE PLUG GRIP

B

32.CHECK INVERTER WITH CONVERTER ASSEMBLY
20.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

OK

21.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

NG

CONNECT SECURELY

21.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

22.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

OK

23.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

NG

CONNECT SECURELY

23.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

24.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR CABLE CONNECTION CONDITION)

A

25.CHECK GENERATOR CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

26.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR CABLE CONNECTION CONDITION)

A

27.CHECK MOTOR CABLE

B

REPLACE MALFUNCTIONING PARTS

C

CONNECT SECURELY

28.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - PCU FUSE)

OK

29.CLEAR DTC

NG

33.REPAIR OR REPLACE HARNESS OR CONNECTOR
29.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

30.CHECK DTC OUTPUT (HYBRID CONTROL)
30.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and wait for 5 seconds or more.


c.

Turn the power switch on (READY) and wait for 5 seconds or more.


d.

Depress the accelerator pedal with the engine stopped and park (P) selected to start the engine and idle it for 10 seconds or more.


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output. A
DTC P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 is output. A
DTCs other than P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 are output. B



g.

Turn the power switch off.



A

31.REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT

B

34.CHECK INVERTER WITH CONVERTER ASSEMBLY
31.REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT
a.

Replace the power module intelligent transistor kit (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS).



NEXT

REPLACE FUSE (PCU)

32.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Check the installation position of the part No. label on the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).


b.

Check the part number of the inverter with converter assembly.

Result:
Result Proceed to
Installation Position of Part No. Label Part No.
Front - A
Top
·

G9200-47160

·

G9200-47161

·

G9200-47162


Other than above. B




A

REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT, MG CONTROL COMPUTER, INVERTER CURRENT SENSOR, INVERTER WIRE, HYBRID BATTERY JUNCTION BLOCK ASSEMBLY AND SERVICE PLUG GRIP

B

REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT, MG CONTROL COMPUTER, HYBRID BATTERY JUNCTION BLOCK ASSEMBLY AND SERVICE PLUG GRIP

33.REPAIR OR REPLACE HARNESS OR CONNECTOR

NEXT

REPLACE FUSE (PCU)

34.CHECK INVERTER WITH CONVERTER ASSEMBLY
a.

Check the installation position of the part No. label on the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).


b.

Check the part number of the inverter with converter assembly.

Result:
Result Proceed to
Installation Position of Part No. Label Part No.
Front - A
Top
·

G9200-47160

·

G9200-47161

·

G9200-47162


Other than above. B




A

35.REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT, MG CONTROL COMPUTER, INVERTER CURRENT SENSOR AND INVERTER WIRE

B

36.REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER
35.REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT, MG CONTROL COMPUTER, INVERTER CURRENT SENSOR AND INVERTER WIRE
a.

Replace the power module intelligent transistor kit, MG control computer with bracket sub-assembly, inverter current sensor sub-assembly and inverter wire sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS).



NEXT

REPLACE FUSE (PCU)

36.REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER
a.

Replace the power module intelligent transistor kit and MG control computer with bracket sub-assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS).



NEXT

REPLACE FUSE (PCU)