Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › FRAME WIRE › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301581 FRAME WIRE A

HYBRID / BATTERY CONTROL  FRAME WIRE  REMOVAL  


PROCEDURE

Hide 58534H 2.REMOVE CENTER FLOOR CARPET COVER LH

Hide 58533F 3.REMOVE CENTER FLOOR CARPET COVER RH

Hide 58804A 4.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

Hide 58817A 5.REMOVE FRONT NO. 2 CONSOLE BOX INSERT

Hide G920Q 7.REMOVE NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide G9200 8.REMOVE INVERTER WITH CONVERTER ASSEMBLY

Hide 17410 9.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 58151 10.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
A251282

Remove the 3 nuts and front No. 1 floor heat insulator.


Hide 52257 11.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

a.

Using a transmission jack, hold the front suspension cross member.

NOTICE:

Be sure to position the transmission jack to properly support the front suspension cross member.



b.
A248480E07
1.594,1.219 1.76,1.375 0.167,0.156 10 true A

Remove the 3 bolts and front suspension member rear brace RH.


c.

Temporarily install bolt A.


Hide 64910J 12.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 13.REMOVE REAR NO. 1 SEAT ASSEMBLY (for Side)

Hide 14.REMOVE REAR NO. 1 SEAT ASSEMBLY (for Center)

Hide 15.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 73360C 17.DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>SEAT BELT>REAR NO. 1 SEAT OUTER BELT ASSEMBLY>REMOVAL).


Hide 73560 18.DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>SEAT BELT>REAR NO. 2 SEAT OUTER BELT ASSEMBLY>REMOVAL).


Hide 64721G 19.REMOVE NO. 1 DECK TRIM COVER (for RH Side)

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 58460D 20.REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 64712F 21.REMOVE FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 64730B 23.REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL).


Hide 24.DISCONNECT CABLE FROM POSITIVE AUXILIARY BATTERY TERMINAL

a.

Remove the terminal cover.


b.
A251284

Disconnect the 2 clamps and remove the nut.


c.
A251287

Disconnect the 2 clamps and disconnect the cable from positive auxiliary battery terminal.


Hide G92Z0 25.DISCONNECT HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the removed terminals with insulating tape.


a.
A251492

Remove the 3 nuts and disconnect the frame wire from the hybrid battery junction block assembly.


Hide 82164 26.REMOVE FRAME WIRE

CAUTION:

Wear insulated gloves.


NOTICE:

Insulate the disconnected terminals with insulating tape.


a.
A253140

Remove the 2 clips.


b.

Turn over the front floor carpet.


c.
A251295

Disconnect the clamp and remove the wire harness protector from the floor panel.


d.
A251291

Disconnect the 2 wire harness clamps from the floor panel.


e.
A251288

Disconnect the 2 clamps from the floor panel.


f.
A251279

Disengage the 3 claws and push the frame wire out from the floor panel.


g.
A214676

Disconnect the connector from the engine room junction block assembly.


h.
A248472

Disconnect the 2 clamps.


i.
A256138

Disconnect the clamp.


j.
A214679

Disconnect the clamp.


k.
A214680

Remove the nut and separate the heater water pipe sub-assembly.


l.
A217198E05
0.063,0.073 0.25,0.281 0.188,0.208 10 false *A 0.052,2.385 0.24,2.594 0.188,0.208 10 false *B

Remove the nut and disconnect the 2 clamps.

Text in Illustration
*A for RHD:
*B for LHD:


m.
A251278

Remove the nut and disconnect the clamp.


n.
A251281

Remove the bolt.


o.
A251294

Remove the 3 nuts and frame wire out from the floor panel.


p.

Disconnect the 3 clamps and remove the frame wire.

A251276

NOTICE:

The clamps are non-reusable parts.