Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.11–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Distance Control Switch Circuit  


DESCRIPTION

The distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The distance control switch is installed in the steering pad switch assembly RH. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch assembly RH (distance control switch) while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

E230014E19
5.354,2.115 6.729,2.542 1.375,0.427 10 false Driving Support ECU Assembly 5.354,1.948 5.813,2.208 0.458,0.26 10 false L60 5.698,0.625 6.135,0.771 0.438,0.146 10 false MODE 5.49,0.51 5.667,0.656 0.177,0.146 10 false 7 4.25,0.615 4.531,0.76 0.281,0.146 10 false L52 4.281,0.427 4.458,0.573 0.177,0.146 10 false 11 4.25,1.479 4.521,1.625 0.271,0.146 10 false L52 4.333,1.292 4.438,1.438 0.104,0.146 10 false 2 2.979,0.615 3.177,0.76 0.198,0.146 10 false z9 3,0.438 3.104,0.583 0.104,0.146 10 false 4 2.979,1.469 3.208,1.615 0.229,0.146 10 false z9 3,1.302 3.125,1.448 0.125,0.146 10 false 6 3.854,0.51 4.198,0.667 0.344,0.156 10 false DIST 3,2.125 4.5,2.5 1.5,0.375 10 false Spiral with Sensor Cable Sub-assembly 0.281,2.031 2.417,2.448 2.135,0.417 10 false Steering Pad Switch Assembly RH (Distance Control Switch) 3.844,1.365 4.188,1.521 0.344,0.156 10 false ECC

PROCEDURE

1.READ VALUE USING GTS (DISTANCE CONTROL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Radar Cruise / Data List.


e.

Check the Data List to confirm function of the distance control switch.

Radar Cruise
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Distance Control Switch Distance control switch signal / ON or OFF ON: Distance control switch on
OFF: Distance control switch off
-

OK:

The display changes in accordance with switch operation.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY RH
2.INSPECT STEERING PAD SWITCH ASSEMBLY RH
a.

Remove the steering RH (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).

U154659E02
5.313,3.073 5.927,3.073 false 0.323,0.313 1.177,1.063 0.854,0.75 10 false *a 5.948,2.99 6.802,3.74 0.854,0.75 10 false *1 4.25,1.146 4.438,1.302 0.188,0.156 6 false 10 4.177,1.146 4.302,1.302 0.125,0.156 6 false 9 4.073,1.146 4.198,1.302 0.125,0.156 6 false 8 3.969,1.146 4.094,1.302 0.125,0.156 6 false 7 3.865,1.146 3.99,1.302 0.125,0.156 6 false 6 4.281,1.021 4.406,1.177 0.125,0.156 6 false 5 4.177,1.021 4.302,1.177 0.125,0.156 6 false 4 4.073,1.021 4.198,1.177 0.125,0.156 6 false 3 3.969,1.021 4.094,1.177 0.125,0.156 6 false 2 3.865,1.021 3.99,1.177 0.125,0.156 6 false 1 4.031,0.396 4.406,0.552 0.375,0.156 10 false z9

Text in Illustration
*1 Distance Control Switch - -
*a Component without harness connected
(Steering Pad Switch Assembly RH)
- -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-4 - z9-6 Distance control switch ON Below 2.5 Ω
z9-4 - z9-6 Distance control switch OFF 1 MΩ or higher



c.

Install the steering pad switch assembly RH (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>INSTALLATION).



OK

3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY RH

3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
NOTICE:

The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may cause airbag deployment. Be sure to read the page shown in the link/brackets.


a.

Remove the spiral with sensor cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).

E343951E01
3.156,3.438 3.51,3.688 0.354,0.25 3.229,1.094 3.583,1.344 0.354,0.25 3,4.438 3.323,4.083 false 3.563,3.979 3.781,4.438 false 1.875,0.188 2.188,0.385 0.313,0.198 10 false *a 3.323,1.135 3.635,1.333 0.313,0.198 10 false z9 3.219,3.479 3.677,3.677 0.458,0.198 10 false L52 2.74,4.458 3.198,4.656 0.458,0.198 10 false ECC 3.708,4.469 4.323,4.667 0.615,0.198 10 false DIST


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
z9-4 - L52-11 (DIST) Always Below 1 Ω
z9-6 - L52-2 (ECC) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Spiral with Sensor Cable Sub-assembly)


HINT:

The spiral with sensor cable sub-assembly makes a maximum of approximately 5 rotations.


c.

Reinstall the spiral with sensor cable sub-assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).



OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)
a.

Disconnect the driving support ECU assembly connector.


b.

Disconnect the spiral with sensor cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L60-7 (MODE) - L52-11 (DIST) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L60-7 (MODE) or L52-11 (DIST) - Body ground Always 10 kΩ or higher



d.

Reconnect the driving support ECU assembly connector.


e.

Reconnect the spiral with sensor cable sub-assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - DRIVING SUPPORT ECU)

5.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)
a.
U155030E02
1.438,1.615 1.083,2.25 true 0.156,0.104 0.406,0.313 0.25,0.208 10 false *a 0.563,1.531 0.917,1.698 0.354,0.167 10 false L52 0.938,2.281 1.271,2.448 0.333,0.167 10 false ECC

Disconnect the spiral with sensor cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L52-2 (ECC) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)


c.

Reconnect the spiral with sensor cable sub-assembly connector.



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR