Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2013.08–2014.11
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1252/52  Brake Booster Pump Motor on Time Abnormally Long  C1253/53  Pump Motor Relay Malfunction  


DESCRIPTION

The skid control ECU detects decreases in the accumulator pressure according to the data from the accumulator pressure sensor, and then starts and stops the pump motor by operating the motor relay.

DTC Code INF Code DTC Detection Condition Trouble Area
C1252/52 311 The pump motor is operating continuously for 178 seconds or more. (When relay malfunction is 98 seconds or more.)
·

Short in motor circuit or motor monitor circuit

·

Motor relay stuck

·

Accumulator pressure sensor malfunction in brake actuator

·

Brake booster with master cylinder (Skid control ECU)


C1253/53 321 With the IG1 terminal voltage 9.5 V or more, the motor drive monitor remains off for 0.2 seconds or more after a motor drive on request.
·

Open in motor circuit or motor monitor circuit

·

Brake booster with master cylinder (Skid control ECU)


↑ 322 The motor drive monitor remains on for 2 seconds or more after a motor drive off request.
·

Short in motor circuit or motor monitor circuit

·

Brake booster with master cylinder (Skid control ECU)


↑ 323 The skid control ECU internal motor drive logical inconsistency continues for 2 seconds or more. Brake booster with master cylinder (Skid control ECU)
↑ 324 An open circuit in both skid control ECU internal motor relays 1 and 2.
·

Open in motor circuit or motor monitor circuit

·

Brake booster with master cylinder (Skid control ECU)


↑ 325 An open circuit in both skid control ECU internal motor relays 1 and 3. ↑
↑ 326 An open circuit in both skid control ECU internal motor relays 2 and 3. ↑
↑ 327 An open circuit in skid control ECU internal motor relay 1. ↑
↑ 328 An open circuit in skid control ECU internal motor relay 2. ↑
↑ 329 An open circuit in skid control ECU internal motor relay 3. ↑

WIRING DIAGRAM

C243136E01
3.988,3.196 4.797,3.365 0.809,0.170 10 ABS MTR1 2.761,5.603 3.179,5.750 0.419,0.147 10 MAIN 0.099,8.069 1.439,8.248 1.340,0.179 10 Brake Booster Pump 5.839,8.073 7.041,8.397 1.202,0.325 10 Brake Booster with Master Cylinder 0.847,1.029 1.223,1.199 0.377,0.170 10 BM1 0.829,2.086 1.206,2.256 0.377,0.170 10 BM2 6.132,0.941 6.608,1.111 0.476,0.170 10 MRO1 6.132,3.055 6.585,3.225 0.453,0.170 10 MRI1 6.132,1.983 6.608,2.127 0.477,0.144 10 MRO2 6.132,4.107 6.508,4.277 0.377,0.170 10 MRI2 0.736,5.562 1.167,5.731 0.431,0.170 10 GND1 6.132,5.03 6.563,5.199 0.431,0.170 10 GND 0.727,6.553 1.158,6.722 0.431,0.170 10 GND2 6.132,5.528 6.563,5.697 0.431,0.170 10 GND2 6.132,5.983 6.563,6.152 0.431,0.170 10 GND3 6.132,6.481 6.563,6.650 0.431,0.170 10 GND4 6.132,6.935 6.563,7.105 0.431,0.170 10 GND5 6.132,7.433 6.563,7.603 0.431,0.170 10 GND6 5.93,4.012 6.106,4.154 0.176,0.142 10 2 5.93,2.929 6.160,3.099 0.230,0.170 10 1 5.868,1.881 6.049,2.023 0.181,0.142 10 30 5.875,0.823 6.049,0.961 0.174,0.138 10 29 1.357,6.24 1.587,6.409 0.230,0.170 10 1 2.845,7.198 3.924,7.388 1.079,0.189 10 Auxiliary Battery 1.357,5.248 1.467,5.395 0.110,0.147 10 2 1.274,6.454 1.544,6.595 0.270,0.141 10 A18 1.274,5.458 1.544,5.599 0.269,0.141 10 A17 1.274,1.991 1.544,2.132 0.269,0.141 10 A18 1.357,1.779 1.462,1.923 0.105,0.144 10 2 1.274,0.934 1.544,1.075 0.269,0.141 10 A17 1.357,0.722 1.462,0.867 0.105,0.144 10 1 4.094,2.933 4.323,3.102 0.230,0.170 10 1 4.515,2.933 4.745,3.102 0.230,0.170 10 2 4.094,3.991 4.323,4.160 0.230,0.170 10 1 4.515,3.991 4.745,4.160 0.230,0.170 10 2 3.988,4.293 4.797,4.463 0.809,0.170 10 ABS MTR2 5.87,4.915 6.049,5.055 0.179,0.140 10 28 5.87,5.429 6.049,5.568 0.179,0.140 10 27 5.87,5.896 6.049,6.035 0.179,0.140 10 26 5.87,6.363 6.049,6.502 0.179,0.140 10 25 5.87,6.848 6.049,6.988 0.179,0.140 10 24 5.87,7.316 6.049,7.455 0.179,0.140 10 23 5.52,8.073 5.840,8.242 0.320,0.170 10 A58

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU or brake actuator), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MOTOR RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Motor Relay ABS motor relay Relay ON/OFF -

*: Electronically Controlled Brake System



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ECB* Motor Relay ABS motor relay / ON or OFF ON: Relay on
OFF: Relay off
-

*: Electronically Controlled Brake System

e.

Check the operating condition of the ABS motor relay when operating it using the GTS.

Result:
Result Proceed to
ABS motor relay in the Data List turns ON/OFF using the Active Test A
ABS motor relay in the Data List does not change using the Active Test B




A

2.INSPECT BRAKE BOOSTER PUMP

B

6.INSPECT SKID CONTROL ECU (MRI TERMINAL)
2.INSPECT BRAKE BOOSTER PUMP
a.
U154952E03
0.948,1.625 0.667,2.677 true 1.198,1.625 1.479,2.677 true 2.469,0.521 2.021,1.594 true 1.323,0.521 1.75,1.583 true 2.188,0.323 2.667,0.49 0.479,0.167 10 false GND2 0.469,2.688 0.885,2.854 0.417,0.167 10 false GND1 1.323,2.688 1.677,2.844 0.354,0.156 10 false BM1 1.229,0.323 1.604,0.479 0.375,0.156 10 false BM2 0.177,0.167 0.375,0.302 0.198,0.135 10 false *a 1.74,0.958 2.042,1.115 0.302,0.156 10 false A18 0.938,0.958 1.24,1.115 0.302,0.156 10 false A17

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the brake booster pump connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-1 (BM1) - A17-2 (GND1) Always Below 10 Ω
A18-2 (BM2) - A18-1 (GND2) Always Below 10 Ω
A17-1 (BM1) - A18-2 (BM2) Always Below 1 Ω
A17-2 (GND1) - A18-1 (GND2) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Booster Pump)



OK

3.INSPECT BRAKE BOOSTER PUMP (GND TERMINAL)

NG

3.INSPECT BRAKE BOOSTER PUMP (GND TERMINAL)
a.
C351654E01
0.385,2.865 0.792,3.115 0.406,0.25 0.344,0.729 0.75,0.979 0.406,0.25 2.323,2.135 1.813,1.656 false 1.052,4.167 1.469,3.75 false 0.115,0.104 0.625,0.323 0.51,0.219 10 false *a 0.417,0.771 0.927,0.99 0.51,0.219 10 false A17 0.458,2.906 0.969,3.125 0.51,0.219 10 false A18 2.177,2.177 2.688,2.396 0.51,0.219 10 false GND1 0.844,4.188 1.354,4.406 0.51,0.219 10 false GND2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A17-2 (GND1) - Body ground Always Below 1 Ω
A18-1 (GND2) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster Pump)



OK

4.READ VALUE USING GTS (ACCUMULATOR PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

4.READ VALUE USING GTS (ACCUMULATOR PRESSURE SENSOR)
a.

Reconnect the brake booster pump connectors.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Accumulator Sensor Accumulator pressure sensor /
Min.: 0.00 V, Max.: 5.00 V
Specified value: 2.90 to 4.20 V When brake fluid is stored in the accumulator: Accumulator pressure changes in accordance with volume of fluid stored in the accumulator


e.

Wait for 30 seconds without depressing the brake pedal.


f.

Check that the accumulator pressure sensor output values change is within the specified range.

OK:

Accumulator pressure sensor output values change is within 0.55 V.




OK

5.RECONFIRM DTC

NG

8.PERFORM ACTIVE TEST USING GTS (SOLENOID VALVE)
5.RECONFIRM DTC
a.

Turn the power switch off (lock).



c.

Turn the power switch on (IG).


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1252/52 and C1253/53) are not output A
DTCs (C1252/52 and/or C1253/53) are output (for LHD) B
DTCs (C1252/52 and/or C1253/53) are output (for RHD) C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

6.INSPECT SKID CONTROL ECU (MRI TERMINAL)
a.
U154750E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A58 1.139,1.787 1.599,2.87 false 0.187,2.883 0.549,3.040 0.362,0.158 10 MRI1 0.878,1.787 0.418,2.87 false 1.367,2.883 1.729,3.040 0.362,0.158 10 MRI2

Turn the power switch off (lock).


b.

Check that the ABS MTR1 (30 A) and ABS MTR2 (30 A) fuses are normal.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the skid control ECU connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-1 (MRI1) - Body ground Always 11 to 14 V
A58-2 (MRI2) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE BOOSTER PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MRI CIRCUIT)

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE BOOSTER PUMP)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the brake booster pump connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-29 (MRO1) - A17-1 (BM1) Always Below 1 Ω
A58-29 (MRO1) - Body ground Always 10 kΩ or higher
A58-30 (MRO2) - A18-2 (BM2) Always Below 1 Ω
A58-30 (MRO2) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.PERFORM ACTIVE TEST USING GTS (SOLENOID VALVE)
a.

Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

HINT:

The Active Test can be performed when the following conditions are met.

·

ABS main relay is on.

·

Park (P) is selected.

·

Parking brake is applied.

·

Vehicle speed is 0 km/h (0 mph).



ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Solenoid (SMC/SRC/SCC) Switching solenoid valve (SMC/SRC/SCC) Solenoid ON/OFF Operation sound of solenoid (clicking sound) can be heard

*: Electronically Controlled Brake System


b.

Perform the Active Test of the solenoid using the GTS.



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released: 0.10 to 0.90 V Reading increases when brake pedal is depressed

d.

Check that the output value of the wheel cylinder does not increase.

OK:

The output value of the wheel cylinder does not increase.


HINT:

If any output value increases, there may be brake fluid leaks in the brake actuator.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER