Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2013.08–2014.11
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1380/64  Stop Light Control Relay Malfunction  


DESCRIPTION

Upon receiving the dynamic radar cruise control system operating signal from the skid control ECU, the relay contact turns on and the stop light comes on.

Upon receiving the emergency brake signal operating signal from the skid control ECU, the relay contact turns on and the stop light blinks (for vehicles with a emergency brake signal).

DTC Code INF Code DTC Detection Condition Trouble Area
C1380/64 761 When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is ON, a signal is not input to the STP2 and EXO terminals for 2 seconds or more.
·

Stop light switch

·

Stop light switch circuit

·

Stop light control relay

·

Stop light control relay circuit

·

Brake booster with master cylinder (Skid control ECU)


↑ 762 When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STP0) is OFF, the signal at the STP terminal is different from the input signal at the STP2 and EXO terminals for 5 seconds or more. ↑

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


HINT:

When C1249/49 is output together with C1380/64, inspect and repair the trouble areas indicated by C1249/49 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1249/49).


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF




OK

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the stop light switch condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.




OK

3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT CONTROL RELAY)

NG

8.INSPECT SKID CONTROL ECU (STP TERMINAL)
3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT CONTROL RELAY)
a.

Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Stop Light Relay Stop light control relay Relay ON/OFF Stop lights come on
EBS Relay*1 Stop light control relay (Emergency brake signal) Relay ON/OFF
·

Hazard warning switch OFF

·

Stop light switch ON



*1: w/ Emergency Brake Signal


b.

Perform the Active Test of the stop light control relay using the GTS.


c.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Relay Output Stop light control relay output / ON or OFF ON: Relay output on
OFF: Relay output off
-
EBS Relay*1 Stop light control relay (Emergency brake signal) / ON or OFF ON: Relay on
OFF: Relay off
·

Hazard warning switch OFF

·

Stop light switch ON



*1: w/ Emergency Brake Signal


d.

Check for stop light control relay operation using the Data List and stop light operation by performing an Active Test.

Result:
Result Proceed to
Data List content and stop light operation are normal A
Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off B




A

4.INSPECT SKID CONTROL ECU (STP2 TERMINAL)

B

6.INSPECT STOP LIGHT CONTROL RELAY
4.INSPECT SKID CONTROL ECU (STP2 TERMINAL)
a.
U191010E02
1.667,1.708 1.063,2.781 false 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.281,0.875 0.573,1.031 0.292,0.156 10 false A58 0.813,2.792 1.229,2.948 0.417,0.156 10 false STP2

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-6 (STP2) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V
A58-6 (STP2) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)

5.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Turn the power switch on (ready).


d.

Perform a road test.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1380/64) is not output A
DTC (C1380/64) is output (for LHD) B
DTC (C1380/64) is output (for RHD) C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

6.INSPECT STOP LIGHT CONTROL RELAY
a.

Turn the power switch off (lock).


b.

Inspect the stop light control relay (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT CONTROL RELAY>INSPECTION).

OK:

The stop light control relay is normal.




OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY)

NG

REPLACE STOP LIGHT CONTROL RELAY

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - STOP LIGHT CONTROL RELAY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


b.

Disconnect the skid control ECU connector and the stop light control relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-3 (STP0) - A28-9 (ACC) Always Below 1 Ω
A58-3 (STP0) - Body ground Always 10 kΩ or higher
A58-21 (EXO) - A28-4 (ESS1)* Always Below 1 Ω
A58-21 (EXO) - Body ground* Always 10 kΩ or higher


*: w/ Emergency Brake Signal


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SKID CONTROL ECU (STP TERMINAL)
a.
U191011E02
1.552,2.135 1.063,2.802 true 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.281,0.875 0.573,1.031 0.292,0.156 10 false A58 0.896,2.813 1.208,2.969 0.313,0.156 10 false STP

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-33 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V
A58-33 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)