Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.03–2013.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1241/41  Low Battery Positive Voltage  C1242/42  Open in IG1 / IG2 Power Source Circuit  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU power source voltage drops, or there is insufficient voltage to operate the ABS main relay, the skid control ECU will store these DTCs.

These DTCs may also be stored if the auxiliary battery voltage drops below 9.5 V.

HINT:

DTC C1256/56 (Accumulator Low Pressure) may also be memorized if there is a drop in power source voltage.


DTC Code INF Code DTC Detection Condition Trouble Area
C1241/41 101 Any of the following conditions when the BS terminal voltage is 9.3 V or less:
1.

Vehicle not decelerated (brake pedal is not depressed) for 3 seconds or more.

2.

While depressing the brake pedal, linear solenoid current does not satisfy 1.34 A.

3.

Vehicle decelerated (brake pedal is depressed) for 0.06 seconds.


·

Improperly connected connector, deformation or corrosion of terminals

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Brake booster with master cylinder (Skid control ECU)


↑ 102 Either of the following conditions when the ECU internal voltage is 6.3 V or less:
1.

When main relay ON is requested, voltage of the relay connection does not exceed 3.5 V for 0.22 seconds or more.

2.

Sensor supply voltage is 4.75 V or less, or 5.25 V or more for 0.06 seconds.

3.

Accumulator pressure sensor output voltage is 4.54 V or less, or 5.46 V or more for 0.06 seconds.


↑
↑ 551 When driving at 3 km/h (1.9 mph) or more, IG1 terminal voltage is 9.5 V or less, or VM1 voltage is 8.6 V or less for 10 seconds or more. ↑
↑ 552 When VM1 voltage is 8.6 V or less, sensor supply voltage is low for 60 seconds or more. ↑
↑ 553 VM1 voltage is 16.6 V or more for 0.8 seconds. ↑
C1242/42 111 Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V or more) for 4 seconds or more.
·

Open or short in IG1 circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Entry and start system (IG start circuit)

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Brake booster with master cylinder (Skid control ECU)


↑ 112 Voltage is not applied to the IG2 terminal (less than 3.5 V), and applied to the IG1 terminal (9.5 V or more) for 4 seconds or more.
·

Open or short in IG2 circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Entry and start system (IG start circuit)

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Brake booster with master cylinder (Skid control ECU)



WIRING DIAGRAM

C243134E03
0.594,0.781 2,1.073 1.406,0.292 10 false from Auxiliary Battery 5.938,0.802 6.188,0.969 0.25,0.167 10 false BI 5.667,5.969 5.906,6.115 0.24,0.146 10 false 23 3.938,1.302 4.042,1.448 0.104,0.146 10 false 1 4.313,1.302 4.417,1.448 0.104,0.146 10 false 2 5.938,1.344 6.25,1.51 0.313,0.167 10 false BS 5.927,3.198 6.344,3.365 0.417,0.167 10 false GND 5.917,3.76 6.333,3.927 0.417,0.167 10 false GND2 5.927,4.333 6.344,4.5 0.417,0.167 10 false GND3 5.927,4.927 6.344,5.094 0.417,0.167 10 false GND4 5.917,5.521 6.333,5.688 0.417,0.167 10 false GND5 5.906,6.115 6.323,6.281 0.417,0.167 10 false GND6 4.135,0.948 5.26,1.104 1.125,0.156 10 false ABS MAIN NO. 2 4.479,0.719 4.583,0.865 0.104,0.146 10 false 1 4.865,0.729 4.969,0.875 0.104,0.146 10 false 2 5.938,2 6.25,2.167 0.313,0.167 10 false IG1 5.938,2.625 6.25,2.792 0.313,0.167 10 false IG2 3.604,1.552 4.76,1.708 1.156,0.156 10 false ABS MAIN NO. 1 0.594,1.979 1.969,2.229 1.375,0.25 10 false from IG1 NO. 1 Relay 3.698,2.135 4.698,2.292 1,0.156 10 false ECU-IG NO. 2 5.75,7.042 7,7.406 1.25,0.365 10 false Brake Booster with Master Cylinder 5.417,7.042 5.688,7.188 0.271,0.146 10 false A58 5.667,5.385 5.906,5.531 0.24,0.146 10 false 24 5.667,4.833 5.906,4.979 0.24,0.146 10 false 25 5.667,4.219 5.906,4.365 0.24,0.146 10 false 26 5.667,3.646 5.906,3.792 0.24,0.146 10 false 27 5.667,3.094 5.906,3.24 0.24,0.146 10 false 28 5.667,0.698 5.917,0.906 0.25,0.208 10 false 14 5.667,1.292 5.906,1.438 0.24,0.146 10 false 15 5.667,1.885 5.885,2.031 0.219,0.146 10 false 16 5.667,2.5 5.885,2.646 0.219,0.146 10 false 12 0.99,2.594 1.99,2.854 1,0.26 10 false from IG2 Relay 4.063,2.729 4.417,2.885 0.354,0.156 10 false IGN 3.385,0.969 3.885,1.125 0.5,0.156 10 false DC/DC 3.375,0.708 3.479,0.854 0.104,0.146 10 false 1 3.76,0.719 3.865,0.865 0.104,0.146 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.CHECK ENTRY AND START SYSTEM (for Start Function)
a.

Check if the entry and start system (for start function) DTC is output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK HYBRID CONTROL SYSTEM

B

2.CHECK HYBRID CONTROL SYSTEM
a.

Check if the hybrid control system DTC is output (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

3.CHECK DTC

B

3.CHECK DTC
a.

Check that no main relay DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Main relay malfunction DTC is not output A
Main relay malfunction DTC is output B




A

4.CHECK AUXILIARY BATTERY

B

4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:

11 to 14 V




OK

5.INSPECT SKID CONTROL ECU (POWER SOURCE TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.INSPECT SKID CONTROL ECU (POWER SOURCE TERMINAL)
a.
U154748E02
1.344,1.854 1.042,2.813 true 2.677,1.844 2.969,2.802 true 2.26,1.688 1.865,0.729 true 2.479,1.688 2.885,0.729 true 0.198,0.188 0.385,0.344 0.188,0.156 10 false *a 0.281,0.875 0.573,1.031 0.292,0.156 10 false A58 0.917,2.823 1.229,2.979 0.313,0.156 10 false IG1 2.896,2.813 3.125,2.969 0.229,0.156 10 false BS 2.823,0.531 3.052,0.688 0.229,0.156 10 false BI 1.719,0.531 2.031,0.688 0.313,0.156 10 false IG2

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-14 (BI) - Body ground Always 11 to 14 V
A58-15 (BS) - Body ground Always 11 to 14 V
A58-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V
A58-12 (IG2) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

6.INSPECT SKID CONTROL ECU (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.INSPECT SKID CONTROL ECU (GND TERMINAL)
a.
U154749E02
2.26,1.802 2.26,1 false 2.365,1.802 2.708,0.667 false 2.146,1.802 1.802,0.667 false 2.469,1.802 3.01,0.979 false 2.052,1.802 1.5,0.979 false 2.646,1.99 2.938,2.76 false 0.198,0.188 0.406,0.344 0.208,0.156 10 false *a 0.271,0.865 0.563,1.021 0.292,0.156 10 false A58 2.031,0.802 2.438,0.958 0.406,0.156 10 false GND4 1.552,0.49 1.958,0.646 0.406,0.156 10 false GND5 2.49,0.49 2.896,0.646 0.406,0.156 10 false GND3 2.813,0.802 3.219,0.958 0.406,0.156 10 false GND2 1.25,0.802 1.656,0.958 0.406,0.156 10 false GND6 2.771,2.781 3.125,2.938 0.354,0.156 10 false GND

Turn the power switch off (lock).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-28 (GND) - Body ground Always Below 1 Ω
A58-27 (GND2) - Body ground Always Below 1 Ω
A58-26 (GND3) - Body ground Always Below 1 Ω
A58-25 (GND4) - Body ground Always Below 1 Ω
A58-24 (GND5) - Body ground Always Below 1 Ω
A58-23 (GND6) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

7.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Turn the power switch on (ready).


d.

Perform a road test.


e.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1241/41 and C1242/42) are not output A
DTCs (C1241/41 and/or C1242/42) are output (for LHD) B
DTCs (C1241/41 and/or C1242/42) are output (for RHD) C


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER