Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.03–2013.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1214/62  Hydraulic Control System Malfunction  


DESCRIPTION

The skid control ECU controls braking force according to the hybrid control system regenerative braking force and inputs the hydraulic pressure necessary for operating each wheel cylinder according to the wheel cylinder pressure sensor.

DTCs may be stored if one of the following occurs:

·

Brake fluid leaks.

·

Wheel cylinder vibrates due to uneven wear of a brake disc.

·

Foreign matter enters solenoid valve.

·

Line pressure drops during air bleeding.

·

Brake pad is replaced.

·

Rotor is replaced.

HINT:

When replacing the brake pad, retracting the brake calipers piston and attaching a new brake pad will greatly increase the clearance between the brake pad and brake disc, which will likely cause these DTCs to be set the next time the brake pedal is depressed. As there is not malfunction, clear the DTCs.



DTC Code INF Code DTC Detection Condition Trouble Area
C1214/62 431 Decrease in hydraulic pressure control performance.
(Pressure increase malfunction)
·

Brake fluid leaks

·

Brake disc rotor excessive wear

·

Brake booster with master cylinder (Brake actuator)


↑ 432 Decrease in hydraulic pressure control performance.
(Pressure decrease malfunction)
↑
↑ 433 Malfunctions such as leaks occur in the SLA valve. ↑
↑ 434
435
Malfunctions such as leaks occur in the SLR valve. ↑
↑ 436
437
Decrease in hydraulic pressure control performance. ↑
↑ 438 Malfunctions such as leaks occur in a hydraulic circuit valve. Brake booster with master cylinder (Brake actuator)

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (brake actuator), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


HINT:

When C1364/61 is output together with C1214/62, inspect and repair the trouble areas indicated by C1364/61 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1246/46).


PROCEDURE

1.CHECK FOR FLUID LEAK
a.

Check that there is no fluid leaks in the brake line between the brake actuator and the wheel cylinder.


b.

Check that the brake is not dragging.

OK:

There is no fluid leaks or dragging.




OK

2.PERFORM AIR BLEEDING

NG

REPAIR OR REPLACE APPLICABLE PART

2.PERFORM AIR BLEEDING

b.

Perform the air bleeding procedure in Bleed Brake System (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>BLEEDING).



NEXT

3.CHECK BRAKE BOOSTER WITH MASTER CYLINDER (ACTUATOR SIDE)
3.CHECK BRAKE BOOSTER WITH MASTER CYLINDER (ACTUATOR SIDE)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the skid control ECU connector 2 minutes after the power switch is turned off (lock).


c.

Check both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

4.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

4.CHECK HARNESS AND CONNECTOR (VEHICLE SIDE)
a.

Measure the voltage and resistance on the wire harness side (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TERMINALS OF ECU).

OK:

Voltage and resistance readings are all normal.




OK

5.READ VALUE USING GTS (WHEEL CYLINDER PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (WHEEL CYLINDER PRESSURE SENSOR)
a.

Reconnect the skid control ECU connector.


b.

Connect an LSPV gauge set.


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Select the Data List on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Wheel Cylinder Pressure Sensor Wheel cylinder pressure sensor / Min.: 0.00 V, Max.: 5.00 V When brake pedal released:
0.10 to 0.90 V
Reading increases when brake pedal is depressed


f.

Check the output value of the wheel cylinder pressure sensor at each hydraulic pressure level during the electronically controlled brake system control.

Standard Voltage:
for Front Wheel Cylinder Pressure Sensor LH:
Hydraulic Pressure
(MPa (kgf/cm2, psi))
Wheel Cylinder Pressure Sensor
(V)
2.0 (20.4, 290) 0.53 to 1.33
5.0 (51.0, 725) 1.12 to 1.92
7.0 (71.4, 1015) 1.52 to 2.32
10.0 (102.0, 1451) 2.14 to 2.94

for Front Wheel Cylinder Pressure Sensor RH:
Hydraulic Pressure
(MPa (kgf/cm2, psi))
Wheel Cylinder Pressure Sensor
(V)
2.0 (20.4, 290) 0.53 to 1.33
5.0 (51.0, 725) 1.12 to 1.92
7.0 (71.4, 1015) 1.52 to 2.32
10.0 (102.0, 1451) 2.14 to 2.94


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

6.CHECK BRAKE DISC

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

6.CHECK BRAKE DISC
a.

Turn the power switch off (lock).


b.

Disconnect the brake pedal stroke sensor connector.


c.

Perform a road test according to Freeze Frame Data or customer problem analysis. Check the brake line pressure vibration caused due to uneven wear of the disc according to brake pedal vibration.

OK:

Brake pedal does not vibrate during braking.


HINT:
·

An unevenly worn disc may vibrate the caliper piston and cause fluctuations in brake line pressure, triggering a malfunction detection condition.

·

The brake pedal does not kick back due to wheel cylinder piston vibration during electronically controlled brake system control.

·

If the brake pedal stroke sensor connector is disconnected, the fail-safe function will prohibit electronically controlled brake system control.

·

The Active Test does not prohibit electronically controlled brake system control when driving the vehicle, so disconnect the stroke sensor connector before continuing with inspection.

·

Disc uneven wear can be checked by measuring the disc thickness variation (See page Brake>BRAKE (FRONT)>FRONT BRAKE>INSPECTION for front, or Brake>BRAKE (REAR)>REAR BRAKE>INSPECTION for rear).





OK

7.RECONFIRM DTC

NG

REPLACE BRAKE DISC

7.RECONFIRM DTC
a.

Reconnect the brake pedal stroke sensor connector.



c.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC (C1214/62) is not output A
DTC (C1214/62) is output (for LHD) B
DTC (C1214/62) is output (for RHD) C


HINT:

If the DTC is no longer output, it can be suspected that it was output due to an improperly connected connector.




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER