Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM J

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  Image from Camera for Intelligent Parking Assist is Abnormal  


DESCRIPTION

The display signal from the rear television camera assembly is transmitted to the radio and display receiver assembly*1 or navigation receiver assembly*2 via the parking assist ECU.

*1: for Radio and Display Type

*2: for Navigation Receiver Type


WIRING DIAGRAM

E307228E02
0.813,4.615 1.146,4.781 0.333,0.167 10 false CV- 0.813,3.979 1.146,4.146 0.333,0.167 10 false CV+ 0.813,5.24 1.146,5.406 0.333,0.167 10 false CB+ 6.125,4.646 6.458,4.813 0.333,0.167 10 false CV- 6.125,4.01 6.594,4.177 0.469,0.167 10 false CV+ 6.125,5.906 6.573,6.073 0.448,0.167 10 false CGND 0.354,7.229 1.552,7.573 1.198,0.344 10 false Rear Television Camera Assembly 3.073,6.75 3.906,6.917 0.833,0.167 10 false *: Shielded 0.354,7.063 0.656,7.229 0.302,0.167 10 false V14 0.323,1.771 2.969,1.958 2.646,0.188 10 false Radio and Display Receiver Assembly*1 1.188,0.604 1.542,0.771 0.354,0.167 10 false L169 3.5,5.51 3.688,5.677 0.188,0.167 10 false * 5.781,7.063 7.042,7.25 1.26,0.188 10 false Parking Assist ECU 6.125,5.271 6.458,5.438 0.333,0.167 10 false CB+ 1.188,4.51 1.323,4.677 0.135,0.167 10 false 2 1.188,3.885 1.323,4.052 0.135,0.167 10 false 3 1.188,5.156 1.323,5.323 0.135,0.167 10 false 6 0.677,5.885 1.146,6.052 0.469,0.167 10 false CGND 1.188,5.802 1.323,5.969 0.135,0.167 10 false 5 5.802,4.469 6,4.635 0.198,0.167 10 false 38 5.771,0.396 5.958,0.563 0.188,0.167 10 false 16 5.802,5.719 5.99,5.885 0.188,0.167 10 false 37 6.125,6.552 6.542,6.719 0.417,0.167 10 false GND1 5.833,6.354 5.948,6.521 0.115,0.167 10 false 4 5.781,5.094 5.969,5.26 0.188,0.167 10 false 14 5.74,4.646 6.073,4.813 0.333,0.167 10 false L65 5.74,4.01 6.073,4.177 0.333,0.167 10 false L65 5.74,5.271 6.073,5.438 0.333,0.167 10 false L65 5.74,5.896 6.073,6.063 0.333,0.167 10 false L65 5.74,6.531 6.073,6.698 0.333,0.167 10 false L64 0.313,2.135 2.958,2.323 2.646,0.188 10 false Navigation Receiver Assembly*2 1.573,0.604 1.927,0.771 0.354,0.167 10 false L173 0.25,8.073 2.302,8.26 2.052,0.188 10 false *1: for Radio and Display Type 0.25,8.375 2.302,8.563 2.052,0.188 10 false *2: for Navigation Receiver Type 5.74,0.615 6.073,0.781 0.333,0.167 10 false L65 5.74,1.24 6.073,1.406 0.333,0.167 10 false L65 5.74,1.865 6.073,2.031 0.333,0.167 10 false L65 1.177,1.24 1.531,1.406 0.354,0.167 10 false L169 1.594,1.24 1.948,1.406 0.354,0.167 10 false L173 5.781,3.813 5.969,3.979 0.188,0.167 10 false 15 5.781,1.01 5.969,1.177 0.188,0.167 10 false 17 5.792,1.646 5.979,1.813 0.188,0.167 10 false 18 6.146,0.615 6.479,0.781 0.333,0.167 10 false NS+ 6.115,1.24 6.448,1.406 0.333,0.167 10 false NS- 6.115,1.865 6.448,2.031 0.333,0.167 10 false NSG 1.271,1.031 1.604,1.198 0.333,0.167 10 false 24 1.26,0.365 1.594,0.531 0.333,0.167 10 false 12 0.927,0.604 1.281,0.771 0.354,0.167 10 false V+ 0.948,1.24 1.302,1.406 0.354,0.167 10 false V- 1.656,0.365 1.99,0.531 0.333,0.167 10 false 12 1.667,1.031 2,1.198 0.333,0.167 10 false 24 3.417,1.448 3.604,1.615 0.188,0.167 10 false * 1.26,0.823 1.594,0.99 0.333,0.167 10 false *1 1.26,1.458 1.594,1.625 0.333,0.167 10 false *1 1.667,0.823 2,0.99 0.333,0.167 10 false *2 1.667,1.458 2,1.625 0.333,0.167 10 false *2

CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the radio and display receiver assembly*1 or navigation receiver assembly*2 after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).


*1: for Radio and Display Type

*2: for Navigation Receiver Type



HINT:

Images may be unclear even in normal conditions if:

·

Electrical devices are used in the cabin (noise may occur in the image).

·

Accessories that generate radio waves have been installed (noise may occur in the image).

·

The outer mirror switch assembly is operated (noise may occur in the image).

·

The multi-display is cold (the image immediately after turning the power switch on (IG) may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night, etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The rear television camera assembly lens is scratched.

·

The rear television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, mercury lights, etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)

OK

2.INSPECT PARKING ASSIST ECU (GND, CB+)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT PARKING ASSIST ECU (GND, CB+)

OK

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY (CV+, GND1)

NG

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY (CV+, GND1)

OK

4.READ VALUE USING GTS

NG

REPLACE REAR TELEVISION CAMERA ASSEMBLY

4.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / IPA/Parking Assist Monitor / Data List.


e.

Check the Data List for proper functioning of the following items.

IPA/Parking Assist Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ASIC Output Status Output condition of camera display/OK or NG OK: Output condition of camera display is normal
NG: Output condition of camera display is abnormal
-



OK

5.CONFIRM MODEL

NG

5.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for Radio and Display Type A
for Navigation Receiver Type B




A

6.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

10.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NAVIGATION RECEIVER ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the L65 parking assist ECU connector.


b.

Disconnect the L169 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-16 (NS+) - L169-12 (V+) Always Below 1 Ω
L65-17 (NS-) - L169-24 (V-) Always Below 1 Ω
L65-16 (NS+) - Body ground Always 10 kΩ or higher
L65-17 (NS-) - Body ground Always 10 kΩ or higher




OK

7.INSPECT PARKING ASSIST ECU (NSG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT PARKING ASSIST ECU (NSG)
a.
U191306E01
0.06,0.033 0.255,0.203 0.195,0.170 10 *a 0.263,0.237 0.705,0.406 0.442,0.170 10 NSG 1.645,0.158 1.974,0.339 0.329,0.181 10 L65 0.787,0.966 0.738,0.336 0.738,0.336 0.645,0.336 false

Reconnect the L65 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-18 (NSG) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Parking Assist ECU)



OK

8.INSPECT PARKING ASSIST ECU (NS+, NSG)

NG

8.INSPECT PARKING ASSIST ECU (NS+, NSG)
a.

Reconnect the L169 radio and display receiver assembly connector.

E361817E02
1.5,1.167 1.917,1.417 0.417,0.25 2.667,1.167 3.083,1.417 0.417,0.25 1.365,2.479 1.313,1.896 false 2.604,2.49 2.604,1.875 false 4.833,1.917 5,1.917 5,1.917 5.063,1.51 false 5.417,1.917 5.25,1.917 5.25,1.917 5.156,1.417 false 4.833,3.583 5,3.583 5,3.583 5.094,3.042 false 5.5,3.583 5.333,3.583 5.333,3.583 5.208,2.99 false 0.729,0.906 1.042,1.104 0.313,0.198 10 false *a 1.25,2.51 1.563,2.708 0.313,0.198 10 false NS+ 2.458,2.521 2.896,2.719 0.438,0.198 10 false GND1 1.583,1.208 1.896,1.406 0.313,0.198 10 false L65 2.75,1.208 3.063,1.406 0.313,0.198 10 false L64 4.229,0.229 4.542,0.427 0.313,0.198 10 false *b 4.656,1.833 4.969,2.031 0.313,0.198 10 false *d 5.458,1.833 5.771,2.031 0.313,0.198 10 false *e 4.354,1.031 4.792,1.229 0.438,0.198 10 false GND 4.375,2.698 4.813,2.896 0.438,0.198 10 false GND 4.25,2.042 4.563,2.24 0.313,0.198 10 false *c 4.646,3.5 4.958,3.698 0.313,0.198 10 false *d 5.531,3.49 5.844,3.688 0.313,0.198 10 false *e


b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Measurement Terminal L65-16 (NS+) - L64-4 (GND1)
Measurement Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Text in Illustration
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen)
*d Synchronization Signal
*e Video Waveform



OK

9.REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

9.REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Replace the radio and display receiver assembly with a new or known good one (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL).


b.

Check if the same malfunction reoccurs when the intelligent parking assist screen is displayed.

Result:
Result Proceed to
Malfunction does not reoccur A
Malfunction reoccurs B




A

END

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

10.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the L65 parking assist ECU connector.


b.

Disconnect the L173 navigation receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-16 (NS+) - L173-12 (V+) Always Below 1 Ω
L65-17 (NS-) - L173-24 (V-) Always Below 1 Ω
L65-16 (NS+) - Body ground Always 10 kΩ or higher
L65-17 (NS-) - Body ground Always 10 kΩ or higher




OK

11.INSPECT PARKING ASSIST ECU (NSG)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT PARKING ASSIST ECU (NSG)
a.
U191306E01
0.06,0.033 0.255,0.203 0.195,0.170 10 *a 0.263,0.237 0.705,0.406 0.442,0.170 10 NSG 1.645,0.158 1.974,0.339 0.329,0.181 10 L65 0.787,0.966 0.738,0.336 0.738,0.336 0.645,0.336 false

Reconnect the L65 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-18 (NSG) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Parking Assist ECU)



OK

12.INSPECT PARKING ASSIST ECU (NS+, NSG)

NG

12.INSPECT PARKING ASSIST ECU (NS+, NSG)
a.

Reconnect the L173 navigation receiver assembly connector.

E361817E02
1.5,1.167 1.917,1.417 0.417,0.25 2.667,1.167 3.083,1.417 0.417,0.25 1.365,2.479 1.313,1.896 false 2.604,2.49 2.604,1.875 false 4.833,1.917 5,1.917 5,1.917 5.063,1.51 false 5.417,1.917 5.25,1.917 5.25,1.917 5.156,1.417 false 4.833,3.583 5,3.583 5,3.583 5.094,3.042 false 5.5,3.583 5.333,3.583 5.333,3.583 5.208,2.99 false 0.729,0.906 1.042,1.104 0.313,0.198 10 false *a 1.25,2.51 1.563,2.708 0.313,0.198 10 false NS+ 2.458,2.521 2.896,2.719 0.438,0.198 10 false GND1 1.583,1.208 1.896,1.406 0.313,0.198 10 false L65 2.75,1.208 3.063,1.406 0.313,0.198 10 false L64 4.229,0.229 4.542,0.427 0.313,0.198 10 false *b 4.656,1.833 4.969,2.031 0.313,0.198 10 false *d 5.458,1.833 5.771,2.031 0.313,0.198 10 false *e 4.354,1.031 4.792,1.229 0.438,0.198 10 false GND 4.375,2.698 4.813,2.896 0.438,0.198 10 false GND 4.25,2.042 4.563,2.24 0.313,0.198 10 false *c 4.646,3.5 4.958,3.698 0.313,0.198 10 false *d 5.531,3.49 5.844,3.688 0.313,0.198 10 false *e


b.

Check the waveform of the rear television camera assembly using an oscilloscope.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


OK:

Waveform is as shown in the illustration.


Item Content
Measurement Terminal L65-16 (NS+) - L64-4 (GND1)
Measurement Setting 200 mV/DIV., 50 μs./DIV.
Condition Power switch on (IG), reverse (R) selected

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Text in Illustration
*a Component with harness connected
(Parking Assist ECU)
*b Waveform 1 (camera lens not covered, displaying an image)
*c Waveform 2 (camera lens covered, blacking out the screen)
*d Synchronization Signal
*e Video Waveform



OK

13.REPLACE NAVIGATION RECEIVER ASSEMBLY

NG

13.REPLACE NAVIGATION RECEIVER ASSEMBLY
a.

Replace the navigation receiver assembly with a new or known good one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).


b.

Check if the same malfunction recurs when the intelligent parking assist screen is displayed.

Result:
Result Proceed to
Malfunction does not reoccur A
Malfunction reoccurs B




A

END

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE