Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2012.03–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U0129  Lost Communication with Brake System Control Module  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U0129 No communication from the skid control ECU continues.
·

Brake booster with master cylinder assembly (Skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (Skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (Skid control ECU)



HINT:

This diagnosis procedure is for when DTC U0129 is output by the power management control ECU (GTS display: PM2 Gateway).


WIRING DIAGRAM

C240392E09
3.802,0.958 3.542,0.958 3.542,0.958 3.385,1.271 false 2.542,1.271 2.375,0.969 2.375,0.969 2.208,0.969 false 0.729,2.344 1.125,2.49 0.396,0.146 10 false 120 Ω 6.208,2.865 6.604,3.01 0.396,0.146 10 false ECM 5.865,2.865 6.146,3.01 0.281,0.146 10 false A57 5.896,2.333 6.292,2.479 0.396,0.146 10 false 120 Ω 0.198,2.99 1.5,3.74 1.302,0.75 10 false Power Management Control ECU 3.667,3.281 4.125,3.427 0.458,0.146 10 false CA2H 3.198,4.063 5.5,4.646 2.302,0.583 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 1.25,3.865 2.156,4.052 0.906,0.188 10 false Trouble Area 3.458,3.552 3.844,3.698 0.385,0.146 10 false IG1 3.198,3.479 3.375,3.625 0.177,0.146 10 false 16 3.708,3.104 3.958,3.25 0.25,0.146 10 false 35 4.365,3.104 4.625,3.25 0.26,0.146 10 false 34 4.854,3.479 5.198,3.625 0.344,0.146 10 false 28 4.458,3.573 4.813,3.719 0.354,0.146 10 false GND 4.156,3.281 4.615,3.427 0.458,0.146 10 false CA2L 1.104,5.021 3.042,5.198 1.938,0.177 10 false : CAN Main Bus Line (CANH) 1.104,5.417 3.042,5.594 1.938,0.177 10 false : CAN Main Bus Line (CANL) 4.24,5.021 5.969,5.198 1.729,0.177 10 false : CAN Branch Line (CANH) 4.24,5.417 5.938,5.594 1.698,0.177 10 false : CAN Branch Line (CANL) 2.875,4.063 3.229,4.24 0.354,0.177 10 false A58 3.865,0.875 5.792,1.063 1.927,0.188 10 false CAN No. 1 Junction Connector 2.292,3.729 3.271,3.906 0.979,0.177 10 false ECU-IG NO. 2 0.313,0.875 2.24,1.083 1.927,0.208 10 false CAN No. 5 Junction Connector 0.125,0.083 1.271,0.563 1.146,0.479 12 false Sub Bus 12: 0.198,2.844 0.385,2.99 0.188,0.146 10 false L6

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), and wait at least 20 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from PM2 Gateway of the power management control ECU, this indicates a sub bus 12 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 12.


Result:
Result Proceed to
U1002 is not output from power management control ECU (GTS display: PM2 Gateway) A
U1002 is output from power management control ECU (GTS display: PM2 Gateway) B




A

2.CHECK DTC (BRAKE SYSTEM)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK DTC (BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

OK:

DTC C1241 is not output.




OK

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)

NG

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154755E04
1.115,2.667 1.656,2.115 false 1.99,2.656 1.76,2.115 false 0.198,0.156 0.385,0.313 0.188,0.156 10 false *a 1.594,0.885 1.896,1.042 0.302,0.156 10 false A58 0.771,2.688 1.135,2.865 0.365,0.177 10 false CA2L 1.896,2.677 2.281,2.854 0.385,0.177 10 false CA2H

Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-35 (CA2H) - A58-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

C

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (SKID CONTROL ECU)