Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2014.11–2020.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

The Combination meter sub-assembly receives a text data signal from the navigation receiver assembly*1 or radio and display receiver assembly*2 via local bus communication.

Based on this signal, audio and visual system or navigation system information is displayed on the multi-information display.

This DTC is stored when the combination meter sub-assembly cannot receive the signal.

DTC No. DTC Detection Condition Trouble Area
B150A After the combination meter sub-assembly receives a registration information signal, which is sent by the navigation receiver assembly*1 or radio and display receiver assembly*2 when the power switch is turned on (ACC), 1 or more times, the combination meter sub-assembly does not receive the signal for 30 seconds or more.
·

Harness or connector

·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2

·

Combination meter sub-assembly



*1: for Navigation receiver type

*2: for Radio and display type


WIRING DIAGRAM

for Navigation receiver type



E309057E05
1.104,1.573 2.396,1.948 1.292,0.375 10 false Navigation Receiver Assembly 4.281,1.594 4.563,1.75 0.281,0.156 10 false L27 4.594,1.594 6.813,1.969 2.219,0.375 10 false Combination Meter Sub-assembly 4.896,0.406 5.198,0.563 0.302,0.156 10 false 29 4.896,0.969 5.198,1.125 0.302,0.156 10 false 28 2.333,0.938 2.635,1.094 0.302,0.156 10 false 3 1.792,0.552 2.25,0.708 0.458,0.156 10 false CNL1 1.771,1.104 2.229,1.26 0.458,0.156 10 false CNH1 5.135,0.552 5.594,0.708 0.458,0.156 10 false MSCL 5.146,1.115 5.604,1.271 0.458,0.156 10 false MSCH 0.802,2.385 3.177,2.583 2.375,0.198 10 false : Local Bus Communication Line 2.75,0.938 3.052,1.094 0.302,0.156 10 false 3 2.333,0.375 2.635,0.531 0.302,0.156 10 false 4 2.75,0.375 3.052,0.531 0.302,0.156 10 false 4 2.292,1.302 2.594,1.458 0.302,0.156 10 false *1 2.708,1.302 3.01,1.458 0.302,0.156 10 false *2 2.292,0.74 2.594,0.896 0.302,0.156 10 false *1 2.698,0.74 3,0.896 0.302,0.156 10 false *2 2.229,0.552 2.646,0.708 0.417,0.156 10 false L172 2.24,1.115 2.656,1.271 0.417,0.156 10 false L172 2.635,0.552 3.052,0.708 0.417,0.156 10 false L173 2.646,1.115 3.063,1.271 0.417,0.156 10 false L173 3.521,2.073 6.458,2.271 2.938,0.198 10 false *1: w/o Intelligent Parking Assist System 3.521,2.375 6.458,2.573 2.938,0.198 10 false *2: w/ Intelligent Parking Assist System

for Radio and display type



E309057E06
1.104,1.583 2.969,1.958 1.865,0.375 10 false Radio and Display Receiver Assembly 4.281,1.594 4.563,1.75 0.281,0.156 10 false L27 4.594,1.594 6.813,1.969 2.219,0.375 10 false Combination Meter Sub-assembly 4.896,0.427 5.198,0.583 0.302,0.156 10 false 29 4.896,0.979 5.198,1.135 0.302,0.156 10 false 28 2.333,0.938 2.635,1.094 0.302,0.156 10 false 3 1.792,0.552 2.25,0.708 0.458,0.156 10 false CNL1 1.771,1.115 2.229,1.271 0.458,0.156 10 false CNH1 5.135,0.563 5.594,0.719 0.458,0.156 10 false MSCL 5.146,1.125 5.604,1.281 0.458,0.156 10 false MSCH 0.802,2.375 3.177,2.573 2.375,0.198 10 false : Local Bus Communication Line 2.75,0.948 3.052,1.104 0.302,0.156 10 false 3 2.344,0.375 2.646,0.531 0.302,0.156 10 false 4 2.75,0.375 3.052,0.531 0.302,0.156 10 false 4 2.292,1.302 2.594,1.458 0.302,0.156 10 false *1 2.708,1.302 3.01,1.458 0.302,0.156 10 false *2 2.292,0.75 2.594,0.906 0.302,0.156 10 false *1 2.708,0.74 3.01,0.896 0.302,0.156 10 false *2 2.229,0.552 2.646,0.708 0.417,0.156 10 false L168 2.229,1.125 2.646,1.281 0.417,0.156 10 false L168 2.635,0.552 3.052,0.708 0.417,0.156 10 false L169 2.625,1.104 3.042,1.26 0.417,0.156 10 false L169 3.521,2.063 6.458,2.26 2.938,0.198 10 false *1: w/ Rear View Monitor System 3.521,2.365 6.458,2.563 2.938,0.198 10 false *2: w/ Intelligent Parking Assist System

PROCEDURE

1.CONFIRM VEHICLE TYPE
a.

Choose the model to be inspected.

Result:
Result Proceed to
for Navigation receiver type A
for Radio and display type B




A

2.CHECK FOR DTC

B

5.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check if navigation system DTCs are output (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR).

Result:
Result Proceed to
Navigation system DTCs are not output. A
Navigation system DTCs are output. B




A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the L172*1 or L173*2 navigation receiver assembly connector.

*1: w/o Intelligent parking assist system

*2: w/ Intelligent parking assist system



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Intelligent parking assist system:
Tester Connection Condition Specified Condition
L27-29 (MSCL) - L172-4 (CNL1) Always Below 1 Ω
L27-28 (MSCH) - L172-3 (CNH1) Always Below 1 Ω
L27-29 (MSCL) - Body ground Always 10 kΩ or higher
L27-28 (MSCH) - Body ground Always 10 kΩ or higher

w/ Intelligent parking assist system:
Tester Connection Condition Specified Condition
L27-29 (MSCL) - L173-4 (CNL1) Always Below 1 Ω
L27-28 (MSCH) - L173-3 (CNH1) Always Below 1 Ω
L27-29 (MSCL) - Body ground Always 10 kΩ or higher
L27-28 (MSCH) - Body ground Always 10 kΩ or higher




OK

4.REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE COMBINATION METER SUB-ASSEMBLY
a.

Replace the combination meter sub-assembly with a new or known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

Turn the power switch on (IG) and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter sub-assembly and navigation receiver assembly.



c.

Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
The audio tab illuminates and DTC B150A is not output. A
The audio tab does not illuminate and DTC B150A is output. B




A

END

B

5.CHECK FOR DTC
a.

w/ Navigation system

i.

Check if navigation system DTCs are output (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>DTC CHECK / CLEAR).

Result:
Result Proceed to
Navigation system DTCs are not output. A
Navigation system DTCs are output. B




b.

w/o Navigation system

i.

Check if audio and visual system DTCs are output (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Audio and visual system DTCs are not output. A
Audio and visual system DTCs are output. C





A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

C

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the I168*1 or L169*2 radio and display receiver assembly connector.

*1: w/ Rear view monitor system

*2: w/ Intelligent parking assist system



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rear view monitor system:
Tester Connection Condition Specified Condition
L27-29 (MSCL) - L168-4 (CNL1) Always Below 1 Ω
L27-28 (MSCH) - L168-3 (CNH1) Always Below 1 Ω
L27-29 (MSCL) - Body ground Always 10 kΩ or higher
L27-28 (MSCH) - Body ground Always 10 kΩ or higher

w/ Intelligent parking assist system:
Tester Connection Condition Specified Condition
L27-29 (MSCL) - L169-4 (CNL1) Always Below 1 Ω
L27-28 (MSCH) - L169-3 (CNH1) Always Below 1 Ω
L27-29 (MSCL) - Body ground Always 10 kΩ or higher
L27-28 (MSCH) - Body ground Always 10 kΩ or higher




OK

7.REPLACE COMBINATION METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE COMBINATION METER SUB-ASSEMBLY
a.

Replace the combination meter sub-assembly with a new or known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL).


b.

Turn the power switch on (IG) and wait 30 seconds.

NOTICE:

A maximum of 30 seconds is required to send/receive the registration information between the combination meter sub-assembly and radio and display receiver assembly.



c.

Operate the steering pad switch assembly and check that the audio tab illuminates.


d.

Check for DTCs (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
The audio tab illuminates and DTC B150A is not output. A
The audio tab does not illuminate and DTC B150A is output. B




A

END

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY