Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2014.11–2020.08
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The temperature can be adjusted and the air inlet can be switched between fresh air mode and recirculated mode by operating switches on the steering pad switch RH. The air conditioning panel (center cluster module circuit) receives operation signals from the steering pad switch RH via the spiral with sensor cable sub-assembly and sends temperature setting and air inlet change signals to the air conditioning amplifier assembly.

WIRING DIAGRAM

E309826E03
1.177,1.406 1.458,1.583 0.281,0.177 10 false R/F 2.792,0.969 3.042,1.135 0.25,0.167 10 false z9 2.781,2.698 3.031,2.865 0.25,0.167 10 false z9 3.094,0.854 3.406,1.021 0.313,0.167 10 false AC1 3.719,0.833 4.031,1 0.313,0.167 10 false AC1 5.458,0.854 5.646,1.021 0.188,0.167 10 false 10 5.094,1.354 5.406,1.521 0.313,0.167 10 false L20 5.458,2.583 5.646,2.75 0.188,0.167 10 false 23 2.813,0.771 3.073,0.99 0.26,0.219 10 false 3 3.094,2.563 3.438,2.74 0.344,0.177 10 false EAU 2.802,2.5 3.021,2.698 0.219,0.198 10 false 8 4.094,2.698 4.385,2.865 0.292,0.167 10 false L52 3.677,2.573 4.063,2.76 0.385,0.188 10 false EAU 4.156,2.5 4.302,2.688 0.146,0.188 10 false 4 4.094,0.979 4.385,1.146 0.292,0.167 10 false L52 5.719,0.99 6.156,1.167 0.438,0.177 10 false SWO 5.708,2.677 6.094,2.844 0.385,0.167 10 false SWG 4.135,0.74 4.323,0.906 0.188,0.167 10 false 10 1.042,2.031 1.583,2.208 0.542,0.177 10 false TEMP+ 1.042,2.646 1.583,2.823 0.542,0.177 10 false TEMP- 0.552,3.583 2.167,3.792 1.615,0.208 10 false Steering Pad Switch RH 2.948,3.063 4.281,3.438 1.333,0.375 10 false Spiral with Sensor Cable Sub-assembly 5.094,1.521 6.979,1.917 1.885,0.396 10 false Air Conditioning Panel (Center Cluster Module Circuit) 5.26,3.083 5.573,3.25 0.313,0.167 10 false L38 5.26,3.854 5.573,4.021 0.313,0.167 10 false L35 5.26,3.229 7.167,3.729 1.906,0.5 10 false Navigation Receiver Assembly*1 0.646,4.792 3.167,4.99 2.521,0.198 10 false *1: w/ Navigation Receiver Assembly 3.521,4.792 6.365,4.99 2.844,0.198 10 false *2: w/ Radio and Display Receiver Assembly 5.26,4.01 7.135,4.385 1.875,0.375 10 false Radio and Display Receiver Assembly*2

PROCEDURE

1.INSPECT AIR CONDITIONING PANEL (CENTER CLUSTER MODULE CIRCUIT)
a.

Disconnect the L52 spiral with sensor cable sub-assembly connector.


b.
U155080E01
1.557,0.232 1.877,0.395 0.320,0.163 10 L52 0.148,0.095 0.468,0.257 0.320,0.163 10 *a 2.21,1.745 2.530,1.907 0.320,0.163 10 AC1 1.827,1.277 2.193,1.785 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L52-10 (AC1) - Body ground Power switch off Below 1 V
L52-10 (AC1) - Body ground Power switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Spiral with Sensor Cable Sub-assembly)



OK

2.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE CIRCUIT - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the L38 navigation receiver assembly connector*1.


b.

Disconnect the L35 radio and display receiver assembly connector*2.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-4 (EAU) - L38-23 (SWG)*1 Always Below 1 Ω
L52-4 (EAU) - L35-23 (SWG)*2 Always Below 1 Ω
L52-4 (EAU) - Body ground Always 10 kΩ or higher


*1: w/ Navigation Receiver Assembly

*2: w/ Radio and Display Receiver Assembly




OK

3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY
a.

Disconnect the steering pad switch RH and spiral with sensor cable sub-assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

E343939E01
4.302,3.042 4.625,3.25 0.323,0.208 2.49,0.594 2.813,0.802 0.323,0.208 2.594,1.146 2.198,0.76 false 2.833,1.573 2.604,1.323 false 4.979,3.094 4.688,3.49 false 4.688,3.656 4.313,4.083 false 0.156,0.167 0.427,0.365 0.271,0.198 10 false *a 4.354,3.052 4.635,3.229 0.281,0.177 10 false L52 2.573,0.604 2.802,0.781 0.229,0.177 10 false z9 1.979,0.573 2.302,0.76 0.323,0.188 10 false AC1 2.865,1.573 3.188,1.76 0.323,0.188 10 false EAU 4.083,4.104 4.406,4.292 0.323,0.188 10 false EAU 5.01,2.979 5.333,3.167 0.323,0.188 10 false AC1

Standard Resistance:
Tester Connection Condition Specified Condition
z9-8 (EAU) - L52-4 (EAU) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right
z9-3 (AC1) - L52-10 (AC1) Center Below 1 Ω
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral with sensor cable sub-assembly to the center position, rotate the spiral with sensor cable sub-assembly 2.5 times clockwise. Then while rotating the spiral with sensor cable sub-assembly 5 times counterclockwise, measure the resistance as shown in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z9-8 (EAU) - L52-4 (EAU) Always Below 1 Ω
z9-3 (AC1) - L52-10 (AC1) Always Below 1 Ω


NOTICE:
·

The spiral with sensor cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral with sensor cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

·

As the spiral with sensor cable sub-assembly may break, do not rotate the spiral with sensor cable sub-assembly more than the specified amount.



HINT:

Text in Illustration
*a Component without harness connected
(Spiral with Sensor Cable Sub-assembly)




OK

4.INSPECT STEERING PAD SWITCH RH

NG

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

4.INSPECT STEERING PAD SWITCH RH
a.

Remove the steering pad switch RH (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

E309798E01
4.209,0.806 4.359,0.34 false 5.652,1.632 5.871,0.942 false 4.209,0.928 4.359,1.394 false 4.237,0.179 4.587,0.335 0.350,0.156 10 AC1 5.876,0.781 6.051,0.937 0.175,0.156 10 *1 4.923,2.194 5.098,2.350 0.175,0.156 10 *2 0.272,0.22 0.622,0.376 0.350,0.156 10 *a 4.237,1.412 4.587,1.568 0.350,0.156 10 EAU 5.587,1.981 5.076,2.268 false 6.352,2.076 6.527,2.232 0.175,0.156 10 *3 5.848,1.815 6.359,2.102 false

Text in Illustration
*1 TEMP + Switch *2 TEMP - Switch
*3 R/F Switch - -
*a Component without harness connected
(Steering Pad Switch RH)
- -

Standard Resistance:
Tester Connection Condition Specified Condition
3 (AC1) - 8 (EAU) No switch pushed 95 to 105 kΩ
3 (AC1) - 8 (EAU) R/F switch pushed 323 to 335 Ω
3 (AC1) - 8 (EAU) TEMP + switch pushed 980 to 1020 Ω
3 (AC1) - 8 (EAU) TEMP - switch pushed 3048 to 3172 Ω




OK

5.REPLACE AIR CONDITIONING PANEL (CENTER CLUSTER MODULE CIRCUIT)

NG

5.REPLACE AIR CONDITIONING PANEL (CENTER CLUSTER MODULE CIRCUIT)
a.

Replace the air conditioning panel (center cluster module circuit) with a new or known good one (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>DISASSEMBLY).


b.

Check that the steering pad switch RH operation returns to normal.

Result:
Result Proceed to
OK A
NG (w/ Navigation System (for Navigation Receiver Type)) B
NG (w/ Navigation System (for Radio and Display Type)) C
NG (w/ Audio and Visual System) D




A

END (AIR CONDITIONING CONTROL ASSEMBLY WAS DEFECTIVE)

B

C

D

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE CIRCUIT - SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-10 (AC1) - L20-10 (SWO) Always Below 1 Ω
L52-10 (AC1) - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING PANEL (CENTER CLUSTER MODULE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR