Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

SLIDING ROOF SYSTEM > HOW TO PROCEED WITH TROUBLESHOOTING

for Preparation Click here


HINT:
  1. Use the following procedure to troubleshoot the sliding roof system.
  2. *: Use the Techstream.



1.VEHICLE BROUGHT TO WORKSHOP

    NEXT


    2.CUSTOMER PROBLEM ANALYSIS

      HINT:
      1. In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
      1. Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
      1. The following 5 items are important points for problem analysis:


      What
      Vehicle, system name
      When
      Date, time, occurrence frequency
      Where
      Road conditions
      Under what conditions?
      Driving conditions, weather conditions
      How did it happen?
      Problem symptoms

    NEXT


    3.INSPECT AUXILIARY BATTERY VOLTAGE
    1. Measure the auxiliary battery voltage with the ignition switch off.

      Standard Voltage:
      11 to 14 V

      1. If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.


    NEXT


    4.INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
    1. Using the Techstream, check if the CAN communication system is functioning normally (Click here).

      Result:
      Result
      Proceed to
      DTC is not output
      A
      DTC is output
      B



    B.
    GO TO CAN COMMUNICATION SYSTEM (Click here)
    A


    5.INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
    1. Using the Techstream, check if the LIN communication system is functioning normally (Click here).

      Result:
      Result
      Proceed to
      DTC is not output
      A
      DTC is output
      B



    B.
    GO TO LIN COMMUNICATION SYSTEM (Click here)
    A


    6.CHECK FOR DTC*
    1. Check for DTCs and make a note of any codes that are output (Click here).

    2. Clear the DTCs.

    3. Recheck for DTCs.

      Result:
      Result
      Proceed to
      DTCs are not output
      A
      DTCs are output
      B



    B.
    GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
    A


    7.PROBLEM SYMPTOMS TABLE
    1. Refer to Problem Symptoms Table (Click here).

      Result:
      Result
      Proceed to
      Fault is not listed in problem symptoms table
      A
      Fault is listed in problem symptoms table
      B



    B.
    Go to step 9
    A


    8.OVERALL ANALYSIS AND TROUBLESHOOTING*
    1. Operation Check (Click here).

    2. Terminals of ECU (Click here).

    3. Data List / Active Test (Click here).


    NEXT


    9.ADJUST, REPAIR OR REPLACE
    1. Check if the sliding roof drive gear assembly has been replaced, or the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly has been adjusted, or removed and installed.

      Result:
      Result
      Proceed to
      The sliding roof drive gear assembly has been replaced, or sliding roof glass sub-assembly or sliding roof drive cable sub-assembly has been adjusted, or removed and installed.
      A
      The sliding roof drive gear assembly has not been replaced, and the sliding roof glass sub-assembly and sliding roof drive cable sub-assembly have not been adjusted, or removed and installed.
      B



    B.
    Go to step 11
    A


    10.INITIALIZE SLIDING ROOF SYSTEM
    1. Initialize the sliding roof ECU (sliding roof drive gear assembly) (Click here).

      HINT:
      If initialization has not been performed, the auto operation, jam protection function, key-off operation and sliding roof open warning will not operate or will operate incorrectly.


    NEXT


    11.CONFIRMATION TEST

      NEXT

      END